Bad Boy Mowers Blade Upgrade - Install 

6'2" 230lbs male unable to loosen factory tightening with a ratchet, you used a crescent wrench. I bow to your strength sir!!

Copperheads are ok, Oregon Fusion Gators are better but more money. Your old blades will clean up and sharpen like new. They're not abused, just used.

Delivered a nice even cut, has the super tight turning ability ru-vid.comUgkx1VWTrayKBdCKAjzAcZ_Eg4dhHTae3LkN also recommend I was looking for, and is just a blast to drive. It takes a little bit to get used to driving one after driving a normal tractor style, but once you've got it, you've got it. If you're cutting lines, you have to be careful spinning the mower around or the back tire will dig a bare spot. Just take it nice and slow during the turn and then it's back to full throttle across the yard!

Great video buddy. I too learned something on swinging those ramps out. Can’t BELIEVE I never thought of that before! I would however use a boxed in wrench instead of that big ass knuckle buster you have there. Again, thanks for sharing. 👍

Thanks for the review. Every since I bought my mower (60" bad boy) I never get a clean cut in the center of the deck. I went ahead and bought using your link. Thanks

Dude! Amazing job brah! Thank you for the very well executed instructional video.💪🏽👍🏽👍🏽💪🏽Be blessed 🤗

Appreciate your time, just making sure if a Bad Boy's blade nut with counter clockwise nut to loosen, Thanks

That lincoln looks great in the back!

Great video. Good to see you again. You are the one who cause me to pull the trigger on my bad boy a couple years ago. I have a Magnum with 54” deck and couldn’t be happier. I am mowing similar country pastureland like you showed previously and about to replace my blades. We have 2.5 acres here in north Texas and the blades have been abused here too. I have a lift for my bad boy and only concern I have is it rocking on its back when I start bearing down on those nuts. Maybe an impact wrench is in my future I don’t know, have I been a good boy? Haha. Thanks again for your videos. I like your style- down to earth. I feel we could sit down and have a drink of coffee or fish together if we ever met. All the best to you on the south coast from north Texas here.

I noticed how amazingly clean your deck is - any advice on how you keep it so clean? Powerwash after each mow? Also, I changed my bolts out on the last blade change - GR8 integrity can be affected if any nicks. Love these blades - just ordered a set. Learned a couple lessons on the lifts - now I turn mine outside too for more room and safety (I kept straight before and chocked). Learn something new every day. Love your videos man.

Hey. Great channel and information. Odd question, do you have a spotify playlist? You always have some cool digital and electronic blues on your videos and they're artists i haven't found yet as a fan of the genre. If so let me know bc the ones i've heard here are great

Thanks, great video and instructions! :)

Great Video. I’ll buy these for sure at $47 for the kit, I already have it in my cart. Thx for the link. I’ll be curious to know how those new blades work for you , they sure look wicked!

Even my impact gun will not budge my mower bolts on the same machine. I broke a 1/2" breaker bar. Guess I better get torch out.

Good looking blades… I use an engine hoist with a belt to lift my zero turn… a lot more room to work.

Bought. Thanks!

Thank you

Thanks!

Sick Continental bro!!

Great video and thank you for taking the time to share. How good is the cut? Do the blades pull the grass up and trim it well? I did replace my blades on my Bad Boy a few weeks ago, and from memory the torque setting on the blade retainer bolts is around 100 ft/lb. The blades are the same shape with the serrated edge and the cut is pretty good. I would recommend using a socket set and breaker bar for undoing the bolts, but you obviously have a good handle on what you were doing.

Nice sled in the background, Dude!

Nice song and why keep the extension & deep socket i have that similar issue but i pry my deck up to use my impact no way I'm doing it by hsnd like that anymore i refuse lbs but good work sir 🍻

Going to change my blades for the first time on my BB 54", the board you use to block/brace the blade while removing/installing - Is there a recommended length for it to be?

No ratchet wrench available ... YIKES!!

Interesting ... There is no "Copperhead" listing for the 54" mulching blades. Do they not make them or just don't list them on Amazon? I see others that claim to be Copperhead but if you read the listing carefully, they are not the same. Does Copperhead have their own web site?

Hey, Mr. South Coast Fab, I have a dumb question for you. Which direction do the blade bolts turn? Reverse threaded or Lefty Loosey?

I WANTED TO SEE IT CUT SOME GRASS LOL

Thanks for the video. I have a 54" Maverick. I like the drive wheels you're using. Is that a Lincoln Continental in the background? Looks like you slammed it. looks nice too.

How much for the blades for a 42 inch BADBOY zero turn? I have a Bad boy MZ

Where is your company located? My PTO clutch is failing already and I just replaced it last week

How the f did you get yours off that easy? Mine won't budge with all the leverage I'm using

I upgraded to the Ballard hybrid blades

That man looked strong loosening bolts torque up to 200 lbs

I can't remove the blades even with a 24 inch breaker bar

Those copper heads do not fit the badboy properly! I have had too many customers buy them and they click together at the ends. This will ruin your spindles, Bearings, and possibly your deck! Don't buy them! Bad Boy has a hardened front edge as well, this keeps them sharp longer. It will cost you more in the long run, running the wrong blades.

damn the music

What model bad boy mower is that?

Is that a continental in the background?

How are the blades doing?

Number 1, that is NOT a dull blade! That blade is hardly used! I change thousands of blade here in the sands of Texas and that blade is in great shape! Heck, I take pieces of blades off and sometimes bent and distorted so bad you can’t tell it was a blade!! Try showing people some kind of reality or or truth! Do you work for a blade company?

Lol