BAL Accu-Slide Cable Replacement Training 

Best cable slide videos

Thank you for making this!!! The manufacturer of my camper put the cable retaining plate on the wrong side of the slide and now it has pulled loose from the back, your video just verified this! Thanks again :)

Really good instructions, almost like you do this for a living. You make it look effortless! Now if I can find you doing a gearbox replacement

This was a very well done video. I don't have to replace my cables (yet) but feel far more confident after watching this series.. Thank you for doing this!

Put the smallest size of heat shrink tubing that’ll fit on the cable, works a little better than electrical tape.

This is a great video. One thing that might make it awesome would be an animation of how it works visually. Still, best video out there so far.

Mine failed yesterday. Luckily I was at home cleaning the coach. So now I have to go see if I can git r done. The only doubts I have is having the facing on the slide to make an adjustment. Otherwise this is one fine video that is much appreciated. If you can maybe you can address removing the facings....just in case. Otherwise I give this a 10....Thank You!!

Awesome! All 3 of my slides have this system.

Wow did you make this easy, i was wondering how to get the cable thru 2 different angled pulleys

Good info!!! Thanks!!!!

How about the standard duty motor gearbbox leaking grease on the slide roof?

Just what I was looking for. My RV has the upper left in cable has pulled out but is stuck and won't pull out? Any ideas.

Does the RV manufacture install the system on there slide rooms? Or does the system come pre installed on a slide room provided by your company?

My stud does not pull out without rotating it. But I can't rotate, since the Metall cable will not give in. How to pull the stud out

Don Hi I liked your video very informative,BUT you have a bare wall, tell me how to replace a broken cable on a slide on an upper living room, with furnature installed and with the slide half way in a person can not get in between slide and front cuboard. it is the upper front (IN) cable. I would like to see what pully if any are inside the hole coming throught the wall before it goes up to the top pullies. Thanks I did learn why my cable broke. We have a 2011 Keystone Montana with 5 slides sold our hoouse to buy the fifth wheel and have done nothing but spent money on fixing things broke, that Keystone or dealer will not fix. I wish it was as easy as your video,keep up the good work

This is a great video but getting to the pulleys and the cables when you have a complete rig is the hard part. This video is all about replacing cables on a stripped down rig. I am finding that pieces I have to remove to access the cables cannot be reattached and am having to buy a LOT of pieces to reassemble.

Hi what happens if the bracket gos on top of the motor it hits then force on top of the motor maybe I could buy longer bolts

I have one cable bottom that keeps getting loosen I keep tighten but I'm running out of adjustment

What is a radius? How do you access the lower pulleys if your slide does not extend completely? The lower pulleys where my problem lies is between my bunk beds and dinette wall. This space is about 6inches wide. My slide does not extend fully for me to access the lower pulleys.

Good Morning. I have a slide out where one of the cables came off the block on top. I think it was the red one. How do I re a just it? And where to order new parts if needed some time later. Jack

I have this Accu Slide system on my Keystone trailer. Recently I’m experiencing an issue where the slide out slides out fine , but doesn’t slide in. After it begins to slide in for a few seconds I hear a loud clicking/banging sound. After manually pushing in the slide out I observed that the cables/chains have quite a bit of slack. From what I’ve researched so far, I should only have about an inch or less of slack correct?. Could it be then that this excess amount of slack I see is the cause of why the slide doesn’t slide in? In which case I would need to add some tension on the IN cables only? Or all.. I do notice excess slack on both.

What does the slide "ride" on? Or, what holds the weight of the slide? is there a roller or something along the bottom? My problem is, there was some substantial moisture on the bottom plywood floor of my slide causing the layers of the plywood to delaminate. I have removed the black moisture barrier and dried it out. reattached the black fabric. looked fine until I ran the slide in and it seems to "scrape" the black fabric off in a few spots. I can't see past the wiper seals to see what is rubbing on the bottom.

HOW CRITICAL IS THE CABLE TENSION ADJUSTMENT? HOW DO YOU DETERMINE IF THE CORRECT CABLE TENSION IS APPLIED TO THE TOP & BOTTOM ON BOTH SIDES OF THE SLIDE? WHAT HAPPENS TO THE ACCU-SLIDE SYSTEM IF THERE'S TOO MUCH TENSION OR TOO LITTLE CABLE TENSION?

we also have Montana 5 slides,same problem

on this cable driven system what would cause the super slide room to start violently shaking the coach when operating the slide in or out and it is loud? rv is a 2016

Does anyone know which swaging tool slot to use for the crimp? I have a swaging tool that has four different size swaging slots. Not sure which one to use.

My slider look like it should go out about 1/2 inch more on the bottom. How can I adjust it. Is there a stop on the bottom?

I have this system on my Keystone Montana 305RL. Sorry i bought it.

Looks easy but all of pulleys are exposed in reality you can't get to the pulleys

How come none of you 🐔🍭 show how to replace the cables if the slide is in ??????