This is a very important thing in architecture. The simplest yet the most challenging at masakit sa likod 😆 I hope this can somehow help. Support this channel. Like. Comment. Subscribe 🧡 ---------- #architecture #drafting #philippines
Tips: not pro but it might work😊 Pag tracing paper yung gamit mo, mas maganda na mas makapal yung gamitin mo. Hindi kasi mahirap i unrolled ang ganun at pag nagka mali ka sa drafting hindi ka matatakot na baka mapunit pag nag bura ka. If your title block is usually measured 1cm all side and you are using rotring t square with wood. Ang purpose nung wood is not just to elevate the acrylic but also use at measurements. Yung edge ng acrylic hanggang sa edge ng kahoy ay may measure na 1cm. You can check it first. Kung sakto, you can use it para mapabilis😅 (ginagawa ko yun pero sinukat ko muna para sure) Eto not applicable kung may time ka pa para ulitin, pero kung kapos ka na sa oras at maraming mali, may mga way naman. Cutter at eraser ang gamit ko. (Nakakaduling lang ‘to ng sobra.) Yung dulo ng cutter dahan dahan mong i rurub sa ink or line na mali. Dahan dahan. Ta’s saka mo lang din burahin ng dahandahan. Acetone din pwede mong gamitin ilagay mo lang sa cotton. (Again this is for minimal wrongs. Pag marami na, might as well eh mag ulit na lang😅kesa mapansin pa ng prof mo.) For guidelines, use H graphite pencils. Hindi sya mas visible. Para mas maganda ang lapat ng pen, try nyo munang burahin yung tracing paper. Gumamit din ng brush para hindi kumalat ang ink instead na kamay ang gamitin mo pag nag tatangal ka ng dust ng pambura mo na sagkalat sa tracing paper! Baka lang makatulong😊
Tip lang po, rub your eraser sa tracing paper muna bago mag start ng drawing. Mas maganda ang result ng inking nyo. At sa guidelines naman use H pencils yung napaka fade talaga na graphite para okay na kahit di mo burahin yung guidelines. Use drafting brush also or kahit anong malapad na brush para makuha yung dust sa paper bago kayo mag ink. Tip ko lang po yan. Yan ginagawa ko dati, ngayung apprentice na haha.
Sa mga hindi skwalado na paper naman madali lang yan. If yung table nyo ay gawa sa kahoy, lagyan nyo na kaagad horizontal line mismo yung surface ng table at vertical line na rin para rekta na tape ng paper. Hindi ka na gagamit ng t square para mag tape ng paper nyo ehehe. If glass na man, same thing lang. Lagyan nyo na lang marker kung saan yung horizontal line at vertical line.
@@cristinerobledo5073 dati wood ginagamit ko. Diy table nga lang yun gawa sa plywood na tira tira. Tapos para even yung surface, nagmasilya na lang ako and paint. Mas nakamura ako eh. Pero kung may pera eh sa glass na lang 😅 mas good lookin pa
@@cristinerobledo5073 pero tip ko lang, dun kana sa mura. Wala naman talaga sa table yan. Nasa skill mo yan sa drafting, esp ang lettering, napakahirap i master yung sobrang clean na lettering. Instead of buying glass drafting table, invest for a beast laptop na lang. If architecture ka, mga 2nd yr college medyo start na yan ng cad and digital rendering eh or maybe 3rd yr so I think sayang yung pera sa mamahalin na table.
This helps a lot! Lalo na yung cross method para malaman yung center ng paper because i used to measure it manually then calculate to be evenly divided. thank you po❤️
Hi po ate sana po next time😅yung presentation board naman pano mo ginagawa . or pano mo pinipresent yung design haha 😅😅but laking tulong ng mga vid nyo po lalo na sa mga arki student.
my only tip is buy a single 2B for shading purposes to show contrast and when making a line have consistent speed and have same line weight because sir will minus 5 you cause he said he see if you write fast or slow and don’t stop when writing a line and see the end point also don’t rewrite the line because that is also a minus 10 I suggest make notes for other subjects and use the lettering used in architecture because that is also 10 points and make so many template at home if your school does not allow printed template
omg im a leftie too ! (upcoming 1st year archi student here !) can u make a video po for tips and tricks for left handed archi students po? i get scared alot since i think its harder 4 me than others na right handed 🥲 love your videos alot !
Ate pano po mag sukat gamit ng t-square huhu kasi minsan kunyari 120mm, eh di naman po sagad yung 1 sa gilid ng paper po mismo kasi nasa edge po ng drafting board yung head ng t-square?
Ate ask ko lang po pag nagdrawing po kasi ako lagi kong nakakalimutan ung unang step saka hindi ko kayang magdrawing sa imagination ko. Parang di po kasi ako magiimprove
I usually do the method na iniikot yung lapis pag naglaline to get precise fine lines since junior high school days up to now 😯😳 magaling na draftsman na ba ako since then? hahahah charr
8:05 totoo! nung mga unang plate na gawa ko napansin ng prof ko na binalikan ko yung line kahit na pinicturan ko lang yung plate napapansin parin ...btw 1st year college ako ngayon😂
Hi Reanne, thank you for the info. I'm a 3D modeler and willing to learn the Architectural aspects of a structural 3D modeling development. I'm a self learning or self taught individual that's willing to prioritize my own portfolio than a professors' bias judgement and forget the aspects of a constructive criticism. I am in charge of a leasure and future construction project in building and designing my own house with multiple layers of sub-basements in a respective surveyed land. For a no degree individual, and you as a second year Architect Student; will you be able to design an Architectural project from start to finish and provide us, the newbies the how's and why videos? I kindly appreciate your time and considerations 🙏
