bedini final build 

🎉fadhav

Thanks brother, but you forgot Kenergy.. I'm aware of all three you mentioned. John was the modern tesla in my view, I'm sure he only shared the small stuff with us and took the important discoveries with him. This motor design was an easy way to help get people started experimenting quickly without needing construction skills. Thanks for the comment!

@@redesign3dp Yes KEnergy really has the circuits sorted. We are lucky to have the opportunity to follow his progress. I've only just become aware of him, but better late than never sir. 😊

No problem brother, I'm glad your interested in this hobby! Keep experimenting and you will unlock your own mysteries. Test the output voltage across the collector diode and the positive battery terminal with a multimeter. It should be over 50v. Be safe don't touch anything while its on...

@@redesign3dpThank you. I also want to ask if the wire from the 5408 diode can be connected to the positive terminal of the battery to charge the battery? My previous operation was driven by a 12-volt transformer connected to the mains power BEBINI. 谢谢 我还想问 5408二极管引出的线能否接电池正极给电池充电？ 我之前的运行是用接市电的12伏变压器 带动的BEBINI

No, it will stall. But if you can charge a second battery by placing it- drive battery positive to charge battery negative. Charge battery positive to output diode.

@@redesign3dp Now I use two 12F batteries to run the equipment. My batteries are all old batteries and the measured voltage is 6F. They cannot be charged with a charger. One battery alone cannot start the Bebini device. So I use a 12V battery charger to connect one of the batteries to power BEBINI. The wires drawn from the UF5408 diode are connected to the third battery. The positive terminal of the two batteries. When the device is not started, the voltage of the second battery is measured to be 6F. After startup, the measurement is about 9F. I'm not sure if I charged the second battery. There is another problem. The only resistor in the circuit will appear burnt black, but even if it is burnt black, the device can still start running. So far this is the case, although I have replaced 3 resistors... (I replace resistors when the unit stops running) I have no idea what is wrong. . . . . The voltage measured between the positive terminal of UF5408 and the positive terminal of the second battery is 12F. Before the resistor burned black, I measured 16F. The voltage between the negative terminal of UF5408 and the positive terminal of the second battery was basically no voltage. Is this correct? Also, the diameter of the coil I used is 0.5MM and 0.3MM. It is thinner than the one in the video... Is it a problem with the coil that causes no high-frequency pulse voltage to be generated? Also, my magnet has the S pole facing outward. It is the same for all three magnets. Do I need the N pole to face outward? Thank you very much for your reply again! Yesterday, the equipment no longer started running, and the three circuit boards did not start up. Today, I made the fourth circuit board and the equipment started up again. But currently the resistor is burnt black but the device is operating normally. (I have replaced the first three circuit boards that did not start with new resistors, but they still cannot start. I can't find the direction at all...) Fortunately, the fourth block was activated~~~otherwise I would have thought it was a dream. . . Ha ha

Yes, it was late. Google bedini ssg circuit. Its very easy to find.

All, they each have an important purpose. The whole system cannot work without each piece.

I still didn't recieve your email, redesign3dp@gmail.com

Magnets need to be in repulsion and must all face the same outward direction. 1n4001 should work

@@redesign3dp Thanks, they are. I may have used 1k VR instead of 10K VR specified in your list. Thanks for replying, appreciate it.

I'd wouldn't use li ion or lipo with that. The hv spike could damage the battery and start a fire potentially. Use on lead acid, or charge up caps.

Luckily i have a buddy that has a room full of lead acid batteries for some reason. ill see if he has any spare dead ones to revive or just charge. Thank you so much for the advice i can't wait for the rest of the parts to get here @@redesign3dp

At least you know whats wrong now! When you get it running don't forget to tape the rotor magnets or they will fly off. Glad your still at it.

@@redesign3dp I found and used the same tape as you did and applied in two layers to be sure it's safe. :D

There is no 12v indicator, thats a 90v neon to safeguard the transistor. Please Google a "bedini ssg circuit" let me know of you have further problems

That little bedini motor is a very basic entry level device for introductory experimentation and learning. Which you are doing nicely my friend. To use the voltage spike effectively, you use it to charge a capacitor bank, then dump it into a battery around 20v at 3 amps into another 12v battery. Check out my cap dump video to get an idea of its effects.

Thank you so much! Through the production of this equipment, I now have more confidence to make larger versions of BEBINI. I will continue to learn. The specific parameters of the production materials and detailed production steps you listed in detail in the video are the key to my success in replicating it. By the way, there are also 3D printing kits. It's really great!@@redesign3dp

I'm glad your on your way brother! Bedini is just one type you can build. My favorites are opto timed pwm pulse motors.

​@@redesign3dpwhat do those ones do?

使用1N4007 是否可以？

Your correct 1n4007. But you can use any rectifier or shotkey diodes.

I'll give it a try. Are you saying put a capacitor in between the coil and the mosfet ina series tank config? Would my output diode go where the coil and cap meet?

Thanks bro!

I like how your experimenting!

It just a small load which changes the spikes. Kenergy has a video demonstrating that unique bedini phenomenon

Would be so kind to upload a video to your channel showing me your setup. That'll make troubleshooting easier. Or if you prefer email me at redesign3dp@gmail.com

The video is quite messy and has been sent to your email. There are also photos of the circuit produced and the condition of the resistor being burned black. The 20-25 coil I replaced today has not started yet. All I can think of at the moment is that the magnet doesn't have its N pole facing out.视频比较凌乱 发到了您的邮箱了。 还有制作的电路照片 ， 以及电阻烧黑的情况 。 今天换上的20 25的 线圈 ， 目前还没有启动 。目前我能想到的就是磁铁还没有N极朝外面这一点。@@redesign3dp

I used back the thin coil I made originally. The device started up again. I measured the output voltage to be 20F. The video of the test has been sent to the second email. @@redesign3dp

@@xingzhe2078 i didn't get anything yet?

I sent the email from my mobile phone. It may be due to the Great Firewall of China, but it was not sent successfully. It doesn't matter, I have sent three short videos to my RU-vid account. The third one shows that a voltage of 1700F was measured between the blackened resistor and the potentiometer. I don't know if my multimeter is broken. Today It has been modified so that the N pole of the magnet faces outward.@@redesign3dp ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-J5VX6ke69XE.html

Sorry, I'm not sure what scema means?

Switch the drive coil leads. Its not a generator, but a mechanical oscillator that produced high voltage emf spikes. Make sure you have a load connected before operation.