bedinisg.com - Demonstration of an Advanced SG with an automatic battery rotation system based on Bedini's 3 battery splitting the positive method. This machine ran way longer than the amp hour capacity of the batteries!
The hardest part is, Petroluim companies paying trolls to discourage young engineers to develop this kind of project... This is working but they will kill you if you publicize your specs on how it works... I made one and its working
Hi Aaron, I bought the "Beyond the Advanced Handbook". I was hoping for better data on the design of new coils (length and diameters of wire, for example), but this is not indicated, or I did not well understand. In the diagram, "A" is it really two batteries (2 X 12V in series) ? Is it the same for "B" and "C" ? The "cap pulser" It has its utility in this new configuration? If so, what is the location? If not why ? Should be 9 strands twisted together, as before ? Thank you Michel
Hi Michael, all specs for the coils are all given in the Bedini SG - The Complete Handbook Series. I think it's in the beginner's book. Peter's presentation you have builds upon everything taught in those books. 18 awg wire - a wire for each power winding and one for the trigger, which can be 18awg or even like 21 awg. If you have 9 wires, then 8 are power and 1 is trigger. Stretch out all 9 wires to 130 feet and then twist them. After twisted, wind on the spool. Keep in mind the direction of the windings so you have a north field on top of the coil or south field on top of the coil when power turns on. You can see a coil being wound here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-DUGh9v2AsuA.html And keep in mind if the polarity is the same as the magnet facing the coil, you will have repulsion mode - not recommended. Have an opposite polarity of the permanent magnets facing coil so it runs in attraction mode and you reduce the bucking losses and the circuit runs cold. A & B (I don't see the diagram now) is 2 x 12 in series for 24 volts. C is reversed single battery so BETWEEN THE POSITIVES, you have a potential difference of 12 volts and that is what the energizer is running on. Current from the 2 in series moves through battery c while running so that current not only runs the energizer but charges that battery at the same time. Scroll to post #6 in this thread: www.energeticforum.com/renewable-energy/20047-question.html In Peter's demo, it was the oscillatory transients (collapsing magnetic field output - the "spike") going to the battery - he wasn't using a cap discharge on output.
What is the difference in performance of the machine with a rotor that has magnets facing north versus a rotor with south facing magnets? I'm building a machine now and I accidentally built my first rotor with south facing magnets so I had to rebuild it, now I have both😊 Building the coil now and will assemble it soon but I haven't been able to test anything yet.
Your models are very small and not built according to the specs outlined in the book. The toy models are only proof of concept to show how they run. Your batteries are too small and have very high impedance, etc...
The original hand book was all wrong, I had to rebuild all those devices to make them work properly, John left out a bunch of info or flat out had schematics wrong. Why would this book be any different? I think I understand what he does anyways.
The SG books are correct and are THE foundation for all of this. John had the schematics wrong? lol No, he got results with the exact schematics he gave to everyone. This Lindemann presentation is a video presentation rather than a book and builds upon the foundation of the SG books and so does Mike Clarke's variation.
"THEE Nickola Tesla" ,, proved that a regular spun coil will act against itself giving it a lesser output than the tesla spun coil. You can test this yourself. wrap a coil with magnet wire around a bolt. wrap second coil as follows use the same length of wire as you did on the first coil only fold wire in half and start wrapping the folded section of wire first on bolt. when done wrapping coil take and cut inner wire where bent.. attach inner wire to outer wire this will leave you with an inner wire and an outer wire. Attach volt meter to ends of wire on first coil.... Place a magnet on end of bolt and then pull magnet off and look at volt meter to see voltage. do the same to the other coil. COIL 2 wrapped tesla style gives out much more voltage than the regular wrapped coil. PROOF. The ONLY good bendini generator is the one where the coils are wrapped tesla style.
Firstly it is the scalability of the Newman motor. The Newman motor can be built with no electronics and can work with high torque applications in traditional brushes systems. Secondly, the Newman motor has been demonstrated by Joe Newman to run heavy equipment like his big eureka motor. Using only transistor batteries, that motor runs industrial grade pump easily, when three phase power is required. The Newman motor has so far in performance wise have been proven to be able to access more torque primarily down to the sheer reliance on mass of copper. There are ways to slim or compact the Newman motor down to become even more desirable by using different materials to increase torque and power density, something that is greatly desired in the world's motor market
I've built an SG with 100% mechanical parts so you can do with it the SG as well. SG was never made for torque, the wheel is a switch and not a motor. Bedini has shown higher torque motors, but they're very different from the SG.
@@gstorm1491 It is possible to make something that runs just with copper contacts to replace the transistors, etc. I don't know how well it would work - would be best to at least have a diode to take the recovery to the desired battery.
Hi Aaron i got your SG bedini book series and its not value for money to be honest with you ya there is tips and tricks here and there its OK to have it in my shelf I am planing to spend more than 500+ bucks in your products to be in my own library so i wont trials of your videos and book content so i now what i am up to and confirm me about the new tesla movie thank you
Peter's demonstration is based on information in those books. The batteries rotated and recycled almost all the energy it used to run the machine to begin with and it gave way more amp hours of running time than can be accounted for according to the battery rating. That means there are energy gains with over 1.0 COP running time. Those books should be hundreds of dollars if not thousands because it is really worth way more than that. Unfortunately, only a small percentage of people will actually apply that knowledge so we proved that what we've been saying is true - Peter demonstrated that at the recent conference.
ya aaron great words what i ment is that for my deep research in sg more than 85% on this series i now it but really you have a great series thats why i am planing to spend my bucks to support this community so my question is to have books contents and videos trial so i now what i am up to thanks
Bedini is just a charger but not give us free energy ,but gives us the loss of money to find out the truth by therory : the circuit of bedini is clearly is a free energy circuit having the feed back diagram ,but in the long run it does not give us the free energy due to the loss of power only give us the loss of time and the money that we spent on it.
It is true? Then you need accurate data on how long the battery will charge how many volts? How Many Amps and How Long time Hours day? We waiting the answer Mr. Bedini, Thank you for answer,