BEST PRESSURE WASHER MOTOR & PUMP COMBO FOR YOUR MONEY $$$$$$ 

You guys are the best. Really tired of seeing unused NM.

Hi, first of all, we thank you for the information you give through your videos 👏🏼🙏🏼. I wanted to ask you a question, I have two GX 270 pressure machines and I would like to increase the gpm! What a treat, can you recommend that I work with Gx 270 to increase the highest gpm. I appreciate your help.

Picked up an old washer after my new brushless monster died in like 40 minutes... defeated the purpose of low maintenance lol. Started looking for pump/chassis as a priority- hoping to find one that didn't run, could swap motor out if needed, still gets me way under cost of new. So for $150 got an older Italian HyPro with a Honda G400 (old 11hp flathead) built in gear reduction (not sure what the reduction is, I'm guessing 2:1 based on pump rpm/motor rpm) 4.7gpm 1800psi. Lower pressure but great volume (which frankly for most of what I do, this is a better setup, especially since I'd like to run a small wet media blaster sometimes.) My question is, can I bring down the orifice sizes some to get more pressure and sacrifice some flow? The thing is beefy, I don't imagine it'd be a problem as long as the motor can chug through. Have you ever used a small diesel on a pressure washer? Too much noise/harmonics? Because a belt drive on a small diesel may actually work really well. The small 6hp 196 diesels probably make a lot more torque under load, could run only a slight underdrive on the pump side. Would running it at slightly more rpm increase pressure at all? Or just flow? Pressure being a result of flow through certain passage/orifice sizes?

whats the link to this gearbox?

Any damaged or blems pump motor for sale

Hey Troy need a new pump on my gx390 and being gear drive with an internal unloaded I’d like to upgrade to at least a reduction gear driven 5gpm pump and external unloaded. would you be able to point me in the right direction to buying the correct unloaders and reduction boxes ?

Nice! I am in the USA! Thank you for sharing. What manufacturer/ part number would be the reduction gear box?

Aloha, wondering if you could help me !!! Thinking 8 gpm at 4000 psi for plumbing jetta. Require the 4000 psi to push through the blockage Honda igx 800 or GX 690 and which pump works best at 4000 psi I think you prefer gear driven ? Rylie

2:55 you know it and what machine👍🏽

Hello, I'm new to your channel. You mentioned a man named John in this video (from the US) Do you know his channel name?

Hi, Had a question you might be able to answer. I have a honda gx390 13 hp engine pressure washer (belt drive). It has a 4.0 gpm pump (1750 rpm) and 3500 psi Can i swap out the pump to a 5.5 gpm @ 3000 or 3500 psi? Just not sure if the rpm on the pump (1450 vs 1750) make a difference on the engine. Just curious because some 5.5 gpm pressure washer use the same gx390 engine but the rpm is lower.

Do you do a video on the v-twin engine I will love to see it?

What anti rust chemical do you use for filling pressure pump on storage?

Hi Troy, Iam building a pressure washer similar to this using the Comet FW2 5530 with the PA 2:1 gear box from Bargroup and the Honda GX 390 (the FW2 has the same pressure and GPM as the RW 5530 only cheaper due to not having hot water seals.) My qustion is at a 2:1 ratio the GX390 is running at 1800rpm, these pumps state that they should be run at 1450rpm maximum. Would this not damage the pump? Are my calculations correct or am I missing something?

Thanks for the video! Um what’s the cost usually for gear reduction, pump, and unloader valve?

What gear drive unit are you using? Is that the ygr1000?

That pump and gear box isn't too heavy to run on that block without support???

Do you guys ever fill the reduction box with gear oil before mounting it to the engine and notice that it slowly leaks oil out of the spot where the engine shaft will insert??? ... I've had two reduction boxes (Both Brand New and Exactly the same type as you have in this video) and BOTH have begun leaking oil. Does it seal better once the engine is mounted to the reduction box? This is really freaking me out.

What do you think about the Comet ZWD-K 4042 4 GPM 4200 psi pressure washer pump ?? i have just bought this because the Honda was a great deal ( normally just window cleaning do the odd pressure washing job ) Will this pump be ok ? even with out a bypass . any tips on keeping it cool and for longtevitiy .. www.agrieuro.de/benzin-hochdruckreiniger-agrieuro-zwdk-15290-mit-pumpe-comet-zwd-motor-honda-gx-390-p-16734.html

Can someone install a 4000 psi pump on a 196cc engine

Do you sale this machine 4000psi pressure washer

is that enough hp for that pump?

honda are the best small engine made, thats why all the china stuff copys honda engines.

I go with the Chinese copy engines. Probably made in the same factory as the Honda