Bind your Mobula8/Mobula7/BassLine(Analog)to ELRS radio the first time

Подписаться 3 тыс.

Просмотров 22 тыс.

50% 1

Edit: 09/26/2023
Do know this tutorial is only good for analog version, the HD version that came out later has a different AIO that uses uart based ELRS receiver, the flashing method will be different. Special thanks to @DanoFPV for pointing this out.
The Mobula8/Mobula7/BassLine has the same FC so the binding to radio process will the same. Although not necessary, It is still suggested to flash your BF firmware to 4.4 to get ELRS 3.0, you get to set up your binding phrase directly at the receiver tab.
Need to flash your Radio ELRS firmware? Check this！
• How to Flash Radiomast...
Just want to setup a bind phrase to your radio? Check this!
• How to setup binding p...
Looking for lipos? Check out CNHL (Affiliated but no extra cost for you) chinahobbyline.com/?ref=1POZw...
Need to flash your TX12/TX16/Boxer ELRS radio to ELRS 3.X? Check out below
• How to Flash Radiomast...
Have some questions? Leave a comment below or message me at my IG account.
iflyxwing?i...
Want to buy me a coffee to support this channel? Thanks in advance!
bmc.link/iflyxwing
0:00 Intro
0:13 SPI & ELRS explained
0:39 Save Backup CLI Files
1:00 Update BF Firmware
1:42 Load backup file
2:21 Set Up Binding Phrase
3:00 Radio Bind Test
4:07 Outro

Хобби

Опубликовано:

31 май 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 159

@iFLYXWings6589 10 месяцев назад

Want to convert your Mobula 8 to a 4K Cinewhoop? Check this: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-V7Qqe3dlAdM.html

@monomills 6 месяцев назад

SPI receivers DO NOT support D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) Modes (Packet Rates) and thus will not bind or sync with a TX module in any of these modes. This helped for me to bind Boxer, because default was F1000.

@andrecook4268 6 месяцев назад

This was what was stopping mine from binding - thanks! Hours of fiddling!

@sa1nts1n 6 месяцев назад

Wow! Thanks a lot! I spent 2 hours trying to bind my remote :/

@centralrif2058 4 месяца назад

Had to setup Packet Rate to 250Hz in lua erls script on my Radiomaster Pocket - bind successful

@ulungprabowo 3 месяца назад

@@centralrif2058hello what else I should know in setting up the mobula7 for Pocket? I am still waiting mine in delivery.

@centralrif2058 3 месяца назад

@@ulungprabowo hi! there was just 1 thing - correct Packet Rate, mobula 7 2.4G ERLS works just great with radiomaster pocket erls

@ellenvorley5299 8 месяцев назад

This is the 1st video I've seen where it actually tells me what I need to do

@iFLYXWings6589 8 месяцев назад

Glad to know the goal of this video succeeded

@andrewyrich6363 7 месяцев назад

Thank you! I'm a complete newbie to this and your video helped me a lot.👍

@iFLYXWings6589 7 месяцев назад

Glad it help. Happy flying

@rodhals5433 8 месяцев назад

VERY helpful thank you straightforward to the point no BS worked the first time. subscribed

@iFLYXWings6589 8 месяцев назад

Glad it help! Thanks for the support

@charliecarpenter2840 Месяц назад

Thanks

@MilneFPV 9 месяцев назад

Thanks for the info, haven't bought the whoop yet but will definitely come watch again when I do!

@iFLYXWings6589 9 месяцев назад

Thank you ! You will love this one ☝️

@ryane146 8 месяцев назад

Thank you!

@iFLYXWings6589 8 месяцев назад

You're welcome!

@getitdone361 10 месяцев назад

Short to the point everything u need nothing you don't great vid

@iFLYXWings6589 10 месяцев назад

Thanks !

@F-ItSeNdItFPV 8 месяцев назад

thank you very much for this bro it really help🤙🚀✈

@iFLYXWings6589 8 месяцев назад

Glad it helped !

@HansBaier 9 месяцев назад

That was very helpful, thanks!

@iFLYXWings6589 9 месяцев назад

I’m glad it helps !

@jupiterjs031 9 месяцев назад

핵심만 설명해 줘서 고마워요.

@iFLYXWings6589 9 месяцев назад

Glad it helped!

@Chocolatato 43 минуты назад

I wonder if it's the same for the tiny hawk 3 plus ELRS, I can't find anyone who bound one so I will try this video with my board targets.

@Quad8ightMix 6 месяцев назад

Very informative and helpful video, do you have a guide how to bind Radiomaster pocket to Mobula7 or 8?thanks in advance for your response.

@iFLYXWings6589 6 месяцев назад

Thank you, sorry, have not received the pocket yet but the terminology should be the same. Will be doing a series of video to demo the setup

@woutersmith7616 5 месяцев назад

Excelent! Bought a Mobula8 with Frsky Rx option. Can I simply bind to my Zorro Tx?

@iFLYXWings6589 5 месяцев назад

If you Zorro TX is Frsky or 4in1 then yes

@woutersmith7616 5 месяцев назад

@@iFLYXWings6589 Thanx👍🤠🇿🇦

@darrenharris6061 23 дня назад

Have you got the factory board hex please, only the red leds are showing on fc now. I need to put it right back to stock.

@iFLYXWings6589 16 дней назад

Sorry, i don't currently have it, but you can try finding it on the happymodel website

@lh7801 5 месяцев назад

Great video. How do i find the binding phrase on the tx12? I dont know what to enter into beta flight since i cant figure out what the binding phrase is on the tx

@iFLYXWings6589 5 месяцев назад

The binding phrase on your TX12 will need to be setup by yourself, suggest to check out my TX12 guide ru-vid.com/group/PL8oE9qQrTLtcWcmj19GB0Zp7ahm3Dvv2P&si=eCtw_TEbZo6X_YwA

@lh7801 5 месяцев назад

@@iFLYXWings6589 thanks bro I'll check it out. Keep up the good work

@xw2672 8 месяцев назад

I am new to the hobby and watched your videos about TX12 MKii and Mobula 7 binding videos, but I can't manage to get it connected through the method you showed in the videos. The video itself is super clear, but after I set the binding phrase through the wifi option in TX12, and Betaflight it just did not response. Any idea of where should I look for the issue?

@iFLYXWings6589 8 месяцев назад

Please confirm your Mob 7 has been flashed to BF 4.4 or above ?

@xw2672 8 месяцев назад

@@iFLYXWings6589 Yes, it is updated to BF 4.4.2, the same as this video showed. I am using TX12 MK ii, and is 3.0.1 firmware, I just can't figure out why this is not binding. Do you have any clue of where should I be looking for?

@lterl3288 7 месяцев назад

@@xw2672 "D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) modes (package rates) are not supported by SPI receivers, and equipment in this mode will not be able to combine with an SPI receiver." This setting is in the elrs script on the transmitter (f1000 is installed on tx12 by default). Write if it helped.

@steriospeaker 5 месяцев назад

Will this work for a mobula 6 elrs (not hd) too? I'm struggling to find a specific video for my new Mob 6. Thanks.

@iFLYXWings6589 4 месяца назад

If your FC board is also the X12 then yes it will work

@asparagus200 4 месяца назад

hey i just tries to follow this but my reciever settings arent saving? im also missing all of the elrs relation commands in the cli tab. please help haha

@iFLYXWings6589 4 месяца назад

Please provide more details, please confirm you have the analog version

@vard7365 4 месяца назад

My Mobula 8 is 3.xx elrs already update firmware. Do i need to upgrade my jumper t-lite v2?

@iFLYXWings6589 4 месяца назад

You do need to make sure your Jumper is at ELRS 3.X for it to bind with the Mobula

@poltergeist6151 6 месяцев назад

I have a mobula7 1s elrs 2.4g drone and a radimaster tx12 MK2 ELRS. When I try to bind them, the image of the drone makes a coup, but does not connect. Bind phrase also does not work. Everything is updated to the max version. Any ideas how to fix it?

@iFLYXWings6589 6 месяцев назад

That doesn’t sound right, if you binding phrase is set up correctly both should have been bounded directly. Can you confirm you Mob 7 is BF 4.4 or above ?

@saviosaltamontes462 7 месяцев назад

I was able to bind it but arm switch does not work under modes Aux 2 for acro/ horizon works fine Aux 3 for turtle works fine , but Aux 1 does not work , but if I change Chanel 5 which is my arm switch h to the opposite direction it works in beta flight. I believe there might be an issue with the board

@iFLYXWings6589 7 месяцев назад

Nope, your board should be fine, double check your settings

@jousiff91 5 месяцев назад

So I still do not have the box for the binding phrase...Can you please help? I went through all the steps you showed

@iFLYXWings6589 5 месяцев назад

Please confirm you have flashed the bf version to 4.4 and select SPI ELRS at receiver tab and hit save

@jousiff91 5 месяцев назад

@@iFLYXWings6589 so I just double-checked but so some reason in the log of BF it says "failed to open serial port". So it didn't flash the new 4.4 firmware.

@juneloko619 8 месяцев назад

Hello would it be possible to flash the new hummingbird v3 to 2.5 in order to bind to my elrs zorro on 2.5?

@iFLYXWings6589 8 месяцев назад

Good question, by theory, yes, but I don’t own or have owned a newbeedrone quad before. If I remembered correct NBD has self developed software ?

@aaronpilla8527 4 месяца назад

What if you don't have a binding phrase to ELRS? Can you hit bind receiver on beta flight and hit bind on your controller?

@iFLYXWings6589 4 месяца назад

Yes, as long you have the same ELRS version

@siniestrorave 7 месяцев назад

flashie mi bassline, si va bien despues sigo con el mobula 8 que tiene la misma controladora de vuelo, solo que yo le puse walksnail hace unos minutos...por las dudas sigo con la 4.3.1 hasta comprobar que no falla el spi elrs 3.0.

@iFLYXWings6589 7 месяцев назад

Which FC are you using? X12 or Crazy F405? Depends on which one your ELRS flashing method my be different.

@karlc9773 6 месяцев назад

Hi followed your instructions but I keep getting"No response from bootloader, programming: FAILED, when trying to flash ?

@iFLYXWings6589 6 месяцев назад

You can try to force the board to go into boot loader mode by pressing the FC button and plug in the USB cable, it should fix you problem

@karlc9773 6 месяцев назад

@@iFLYXWings6589 where is the boot button on the mobula 8 ?

@aenitro 8 месяцев назад

Can the Mobula be bound to a Spektrum (Dx9) radio? Thanks

@iFLYXWings6589 8 месяцев назад

No, I will assume you need a Spektrum receiver

@aenitro 8 месяцев назад

@@iFLYXWings6589 Thanks for your response.

@Asian_Jewelry_International 6 месяцев назад

Tim, The Mobula that I bought from Banggood don't have any Data. How to get them?

@iFLYXWings6589 6 месяцев назад

Here’s the link for the factory default CLI dumps. Check to see if you find the one you need If not, e-mail me I’ll send you my presets www.happymodel.cn/index.php/2023/05/05/default-factory-dump-file-for-mobula8/

@Asian_Jewelry_International 6 месяцев назад

@@iFLYXWings6589 I have nothing in my back up what so ever only says default nosave. My first time doing this, my ELRS Boxer won't connect to my wi fi either. This is complete mess, I did go to edge tx and could not find the smt somthing to update the firmware.

@fliegerdieter2843 6 месяцев назад

How can I update the receiver to ELRS 3.3.1? My transmitter also has ELRS 3.3.1. Both have to be on the same level, right?

@iFLYXWings6589 6 месяцев назад

If you have a SPI ELRS receiver, this video should explained the steps, also as long you RX & TX are both in 3.X you are good

@fliegerdieter2843 6 месяцев назад

Ah OK Thank you@@iFLYXWings6589

@vedmarth 8 месяцев назад

I bought Mobula8, when I try to select SPI Rx and save, it goes back to Serial all the time, what can be the issue?

@iFLYXWings6589 8 месяцев назад

Double check which model you have if its a HD(walksnail/AVATAR/DJI) then the AIO is F405. This board will have a serial based ELRS

@vedmarth 8 месяцев назад

@@iFLYXWings6589 actually I found instructions and its indeed works with serial connection

@timal974bzh 5 месяцев назад

Bonjour jai commande un mobula 9 en spi frsky faut il achete un recepteur suplementaire ou est il directement integre merci

@iFLYXWings6589 5 месяцев назад

Sorry, don’t fully understand what you mean. If you have a Frsky receiver, you will need a Frsky radio or a 4in1 module

@seriousserg4128 8 месяцев назад

I flashed mobula 8 to 4.4 and after arming, 1 or 2 motors do not spin. What is the problem ? How to check motors? I checked the connectors - its ok. Betafly has a reaction to the motors when the sliders move.

@iFLYXWings6589 8 месяцев назад

Please confirm you have save and loaded your presets after flashing ?

@seriousserg4128 8 месяцев назад

@@iFLYXWings6589 I solved the problem, but I'm not sure of the source yet. To test the drone, I used a 1s battery 660mah, which may not be enough for the initial spin-up of the motors. In the manual on the happymodel website I saw the ESC settings for the Bluejay configurator . There is a significantly higher min start power than the default ). After flashing new values and taken a fuller battery, the motors began to spin up as expected . Joining the FPV is not as easy as I imagined :)

@iFLYXWings6589 8 месяцев назад

@@seriousserg4128 I see, glad that you resolved the issue!

@lynsmith1096 4 месяца назад

I messed up on binding my Mobula8 can you tell me how to reset the Mobula 8 to factorl settings

@iFLYXWings6589 4 месяца назад

Yes, you can go to the Happy model website to download the CLI files for the mob 8

@lancekinshella5817 7 месяцев назад

How do I do this with the frsky version? I'm trying to bind to my jumlert18

@iFLYXWings6589 7 месяцев назад

For Frsky, i am not so sure. but the general idea is to press the button on the FC or click bind at Betaflight and then hit bind on your Radio. Also double check to see if your protocol is at D8 or D16

@lancekinshella5817 7 месяцев назад

@@iFLYXWings6589 I got it.... switched from d16 to d8 and bound right away

@iFLYXWings6589 7 месяцев назад

@@lancekinshella5817 Glad you got it fixed

@k1ortia 8 месяцев назад

iv been trying to get my Bassline to bind for over 4 months on and off, iv tried everything and still cant get the bloody thing to bind. Very frustrating. Iv updated the board to the newest betaflight, My transmitter is also on the same firmware, iv tried with and without binding phrases and still nothing. it just sits there blinking red and green. Grrrrrrrrrrrrr!

@iFLYXWings6589 8 месяцев назад

Which AIO board do you have? X12 or F405 ? Reason I’m asking, X12 is SPI F405 is serial. Also, have you plug it into betaflight to check the receiver tab? Any stick inputs ?

@k1ortia 8 месяцев назад

@@iFLYXWings6589 it's the Crazybeef4fSX1280. Which is obviously an spi based board and I have correctly selected this in the receiver tab, then ELRS. I have updated the board to the latest Betaflight firmware, and my ELrs transmitter is on version 3.2.1. If tried binding with a binding phrase and without. Used both 250hz and 500hz nothing. Also tried in hybrid mode instead of wide, nothing. Even took the quad apart to bind manually using the tiny bind button, guess what... nothing. All it does once plugged in or with a battery connected is blink red and green, Which to my knowledge is ready to bind. But nothing at all. I do believe i have a faulty board. If there's something iv missed them I'm all ears. Cheers

@keenwa397 8 месяцев назад

everytime i try to flash the mobular 8 it says failed to open serial port. Does anyone know the solution to fix this?

@anthony6745 8 месяцев назад

Same issue

@iFLYXWings6589 8 месяцев назад

Some dump reason maybe the USB cable, some even with the data mark will still not be recognized. Try a different cable to see if it works. Or try to force the FC into DFU mode to see if it works, press the button on the fc and plug in the cable at the same time should do the job.

@dominiczaninovich7643 8 месяцев назад

Any tips for “failed to open serial port” error?

@iFLYXWings6589 8 месяцев назад

Which part are you referring to? When connecting the drone to BetaFlight?

@sltproductions1285 8 месяцев назад

after flashing

@matek115 8 месяцев назад

Thanks mate! I thouhgt something is wrong because elrs wouldn't create wifi...

@iFLYXWings6589 8 месяцев назад

Glad it helped ! Yes the mob 8 is using a SPI board

@RafalGalinski_drony 3 месяца назад

I fly on CRSF daily, and find ERS so frustrating. Imagine: pure field, no wifi, no computer and friend left me a drone. How can can I bind it offline? Is it not a disaster?

@iFLYXWings6589 3 месяца назад

Well ELRS does have a initial learning curve but once you understand it, it becomes quite easy

@Cuisinenomade1 10 месяцев назад

I had to send mine back, rx defected. Spi rx are not so good apparently

@iFLYXWings6589 10 месяцев назад

This is the problem with AIOs ….convenient but when something breaks …bye for the whole unit

@coregenesis4630 6 месяцев назад

hi, i had follow all the step and i still got issue to connect my drone to my radio, i bind but noting happend, can i know here i wrong ?

@iFLYXWings6589 6 месяцев назад

Can you please advise what equipments are you using? I need to know the exact model of your drone and your radio to offer you a solution

@coregenesis4630 6 месяцев назад

@@iFLYXWings6589 hi, is ok, I got it fixed, is choose the 250hz in the radio, maybe u can add notes in there, so that can helped more haha, mine using elrs 3, so maybe is the reason need chg the hz

@siniestrorave 7 месяцев назад

tuviste algun problema de rango en el spi elrs 3.0 o funciona bien? tengo miedo de salir de la version 4.3.1 de happymodel y que tenga algun problema... Gracias. Emiliano

@iFLYXWings6589 7 месяцев назад

Nope, i dont recall having a range issue, but depends on how far you are looking. round the house no problem

@siniestrorave 7 месяцев назад

Happymodel support told me officially that the version 4.4.2 will works on analog mobula 8 & analog bassline, always using the x12 FC. They dont recomend 4.5 yet

@siniestrorave 7 месяцев назад

Bueno hoy probé el mobula 8 en el parque y con la versión 4.4.2 el spi pierde recepción a los 40 metros ....así que voy a volver la versión original perdiendo el osd HD...sino tendría que poner un elrs serial...pero x el momento no lo voy a hacer....

@iFLYXWings6589 7 месяцев назад

@@siniestrorave It is completely up to you~Btw if your Mob 8 is HD then you do not need to flash BF, you just need to flash your serial based ERLS receiver ERLS

@siniestrorave 7 месяцев назад

@@iFLYXWings6589 My Mobula 8 came analog and I added a VTX walksnail. I wanted to update to 4.2.2 just to get the HD OSD, but the SPI ELRS range doesn't work properly and I lose the drone at 40 meters. I am going to stay on version 4.3.1 as there are no problems with the SPI ELRS 3.0 unless I add an external ELRS receiver later

@user-zj9qw3qp8w 3 месяца назад

After flashing the drone, the motors don't start, can you help?

@iFLYXWings6589 3 месяца назад

Please confirm you have reloaded the presets after flashing.

@voosempre.9946 2 месяца назад

Boa tarde amigo meu drone bateu num galho e rodopiando caiu perdendo sinal com meu radio e nao vinculou mas o que pode ter ocorrido. Meu rádio é ocomando 8 ELRS

@iFLYXWings6589 2 месяца назад

Sorry, need more details to help you. First, please start with which drone do you have ?

@voosempre.9946 2 месяца назад

Mobular 8 amigo , até agora não consegui vincular com o rádio depois da queda eu ainda fiz um vôo mas quando coloquei no betaflith ele até deu sinal e depois foi diminuindo e não vinculou mas.

@iFLYXWings6589 2 месяца назад

@@voosempre.9946 Try reflating the betaflight firmware it should fix the issue

@voosempre.9946 2 месяца назад

Vou tentar

@daniel.91o6 7 месяцев назад

I succesfully binded my mobula8 to my controller but when i disconnected the drone with the pc, my radio says telemetry lost and the controller doesnt seem to control the drone

@iFLYXWings6589 7 месяцев назад

Ok.... just want to confirm, have you also plugged in a lipo?

@daniel.91o6 7 месяцев назад

yes i did@@iFLYXWings6589

@daniel.91o6 7 месяцев назад

Ma radio has the 3 bars signs for the connexion but the switches and stuff still wont work@@iFLYXWings6589

@andersonmachado6146 7 месяцев назад

i did the exactly same thing and it didnt work =/. I click on bind on betaflight, and when i click bind in lua script, the quad model on betaflight mades a flip and nothing hapens wtf kkkkk, maybe a problem on rx? There is anyway to check it?

@iFLYXWings6589 7 месяцев назад

Did you reloaded your presets? The binding method is based on using bind phrase which is the recommended method, try to set up your bind phrase for both your RX and TX

@lterl3288 7 месяцев назад

"D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) modes (package rates) are not supported by SPI receivers, and equipment in this mode will not be able to combine with an SPI receiver." This setting is in the elrs script on the transmitter. Write if it helped.

@poltergeist6151 6 месяцев назад

do you fix that?

@albaniansuperiorshqipetari8055 6 месяцев назад

I wonder where the binding button is on Mobula 8? I want to bing it manually. Anyone ?

@iFLYXWings6589 6 месяцев назад

It is on your FC the little yellow black dot

@albaniansuperiorshqipetari8055 6 месяцев назад

@iFLYXWings6589 I can't see it. I can see the boot button but not bind button. I. Looking at the mobula 8 manual and the diagram of the FC does not show it, do u have any pic link of the FC

@iFLYXWings6589 6 месяцев назад

@@albaniansuperiorshqipetari8055 the boot button will be your bind button as well. But still suggest you to bind it with a bind phrase

@albaniansuperiorshqipetari8055 6 месяцев назад

@iFLYXWings6589 I got it now I'm just going to bind it from configurator on receiver tab. Thanks for ur help Man

@albaniansuperiorshqipetari8055 6 месяцев назад

I've got it ready to fly now but my eachine goggles are not connecting to the drone, normally I conected them but just Turing power on and search for channels usually it finds the channel easily. This time I can't conect I tried two different eachine goggles, they work fine with my other drones. What do you think?

@tc.isyammudin.hj.ismail 25 дней назад

When i try to update it says failed to open port

@iFLYXWings6589 22 дня назад

1st try a few different cables- this is mostly the issue 2nd if cables is not the issue, run the impulseRC driver fixer to see if it fixes the issue impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe

@Evan-rq2ee 6 месяцев назад

binding phrase box doesnt pop up

@iFLYXWings6589 6 месяцев назад

You need to save and restart

@puc19 5 месяцев назад

Does this work with mobula 6

@iFLYXWings6589 5 месяцев назад

the concept is the same, just the mob 6 has a different FC thus your target will be different

@puc19 5 месяцев назад

ok @@iFLYXWings6589

@puc19 5 месяцев назад

For so,e reason it is stuck on “Initialising reboot to boot loader

@iFLYXWings6589 5 месяцев назад

@@puc19 This happens, what you need to do is 1. Remember which target your FC is 2. Press and hold the button on your FC and at the same time plug in the USB, this will force the FC into bootloader mode, if you do not see "Exit DFU mode" button glow up, try the process again

@puc19 5 месяцев назад

@freeflightfilms7403 8 месяцев назад

could you send me the backup file please

@iFLYXWings6589 8 месяцев назад

Can you please email me at piggycraftsman@gmail.com? I will send over the file

@DanoFPV 8 месяцев назад

This video is incorrect, because a Mobula8 can come with a UART ELRS. You should specify that in the video otherwise people are gonna try flashing BF when they dont have to with a UART ELRS

@iFLYXWings6589 8 месяцев назад

I agree , this video was made prior of the HD version that came out with a different AIO. Let me update it to analog only

@darrenharris6061 23 дня назад

Its just not workin now! Regrettin buyin this mob8

@iFLYXWings6589 14 дней назад

Sorry to hear this any particular issues?

@Electrixzzz 4 месяца назад

is this everything I need to do to bind my radio and drone? i'm having some trouble getting them to bind

@iFLYXWings6589 4 месяца назад

In most of the cases, this will be all you need to do.

@user-rh4ev1ls3c 4 месяца назад

Спасибо👍🤝

@morvedibile5773 Месяц назад

mine won't bind i tried everything. do i need to program the transmitter too? isn't the binding phrase written in the tx screen? i updated the firmwares i've seen a lot of videos but no one spends a word more on the binding process pls help🥲

@iFLYXWings6589 Месяц назад

Yes, you need to program the TX as well. 1. Make sure your TX is also at ELRS 3.X 2. Set up the binding phrase to be same as your TX 3. If you RX is SPI based set your packet rate to 500hz This video will show you how to flash the firmware of the TX How to Flash Radiomaster TX12 MK2 ELRS Firmware To ELRS 3.0 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-5gUl62wKzgM.html