BLheli-S Free RPM Filtering JazzMaverick vs. JESC (How-To)

Подписаться 331 тыс.

Просмотров 93 тыс.

50% 1

Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: www.fpvknowitall.com/ultimate...
SUPPORT ME ON PATREON at: bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: www.fpvknowitall.com/support-me/
---
RPM Filtering with bidirectional dshot is one of the most powerful ways to get better performance out of your micro quadcopter or Tiny Whoop. But BLHeli_S ESC's don't support it by default. That's where JESC and JazzMaverick come in. These are two aftermarket firmwares that you can put on your ESC to enable RPM filtering with bidirectional Dshot. But there's a difference. JESC costs money. JazzMaverick is free. I'll show you how ot install either of them and get them running.
-- REFERENCELINKS --
Download JESC Configurator here:
github.com/jflight-public/jes...
Purchase JESC licenses for bidirectional Dshot at:
jflight.net/
Download BLHeli Configurator here:
github.com/blheli-configurato...
Download BLHeli_S JazzMaverick firmware at:
github.com/JazzMaverick/BLHel...
AFTER BIDIRECTIONAL DSHOT IS WORKING
How to set up RPM filtering:
• Betaflight 4.1 RPM Fil...
How to tune filters for best performance with RPM filtering:
• Betaflight 4.1 RPM fil...

Опубликовано:

30 дек 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 399

@jasonbeamish5576 4 года назад

Thank you for your videos. I am 45, had no interest in learning all the beta flight etc. I only bought spektrum bnf, easy setup etc. Now, I have built a drone, own a Jumper T16 and am all in on this stuff. What a great hobby. If not for your videos I would have never left bnf. Nice that I found someone that can explain things in step by step that does not put me to sleep. I am a total geek watching your videos as I set stuff up etc.

@keithacebedo8800 4 года назад

Same here. I'm 46 and his videos are great. Super nice guy on facebook answering my questions. I joined his patreon.

@-Gruntled 4 года назад

I installed jesc and BF 4.1 on my Mobula 6 after less than a dozen flights to see what it would do to my flight time. I used only the 48khz, and therefore free, version. Here's my results with three batteries both before and after. Not up to Bardwell testing standards, but maybe good enough for a RU-vid comment :) I also improved my flight time with jesc and BF4.1 BF 4.0 BLHeli 16.7 jesc and BF4.1 Happymodel 300mAh brand new 0:03:14 0:05:17 GNB 350mAh brand new 0:02:58 0:05:01 GNB 300mAh months old 0:02:42 0:04:36

@BimoWicaksono 4 года назад

could you inform us which type of motor do you use? 19kv or 25kv versions?

@-Gruntled 4 года назад

Bimo Wicaksono I have the 19s. Also, I was cruising around the house at a steady pace, not pushing it since a crash would mess up my test. For the second set of flights one of my pals with a Mobula6 was also watching so I had a witness 😀

@BimoWicaksono 4 года назад

@@-Gruntled I'm curious what's the flight time results for 25kv version

@OberFreak83 4 года назад

I tested my Mobula 6 (25k) BF4.1.3 with JESC 24kHz, 48kHz and 96kHz: BLH 16.7 JESC 24kHz JESC 48kHz JESC 96kHz 0:03:04 192mAH 0:03:10 197mAH 0:04:15 201mAH 0:04:23 195mAH 100% +3% +38% +43% Each Firmware test is an average of 3 hovering flights with brand new GNB 300mAH that came with my Mobula. Batteries where charged to 4.35V and landed at my low voltage warning 3.1V

@Rich-TeaFPV 4 года назад

I always want my quads to fly gooderer, the betterest they can. Thanks Joshua 👍👍

@padcom 4 года назад

I bought JESC for all my quads running BLHELI-S and I strongly feel this was the best spent money I ever did! It's cheap enough yet the difference is CRAZY in my little Snapper 7!

@cccagley5276 4 года назад

I agree. I can't understand people complaining about the small fee to improve a quad so much. The guy who did the code deserves it.

@franza.d.morales8529 4 года назад

What were your snapper 7 improvements?

@billrubeck7104 4 года назад

Great work Joshua. I really appreciate all that you do here! As a new flyer, all that you provide is priceless!

@ZylonFPV 4 года назад

11:16 - “it might not be great for the ESC to go to 100% with the props off...” 11:18 - goes to 100% with the props off 😂

@JoshuaBardwell 4 года назад

Joke's on you. My props were actually on!

@ZylonFPV 4 года назад

Joshua Bardwell it did sound like they were on actually. The motor sliders in BF can be a bit glitchy like that, it’s happened to me before. Good thing it wasn’t a 5” with props on!

@KamilK3 4 года назад

Yes, if it was 5-inch quad with props installed, JBs face would not be very pretty now

@stevo43068 4 года назад

That's when I clicked the thumbs up for this video.

@uavtech 4 года назад

Yeah, that is what is nice about whoop class!! :-)

@jeffkubascik7830 4 года назад

Thank you for the video! This helped me set up RPM filtering on my Trashcan, and it flies great! I also tried out the JESC 48kHz PWM early access firmware, and WOW does it make a difference. My flight time on 2S went from 2:30 @ 24kHz to 3:40 @ 48kHz. I believe the power savings are coming from the motor controller FETs. After enabling the core temperature on the OSD, I noticed the temperature dropped from 162F @ 24kHz to 124F @ 48kHz.

@fpvwing 4 года назад

Glad I saw this. Happy to support Jesc. Just installed this week.

@deant6627 4 года назад

I was certainly happy to purchase the jesc licences for my eachine trashcan. I am running jesc 48khz and Betaflight 4.1.2 with bidirectional DShot. It all is flying so good with cold motors. With 48khz its definitely not as hungry on the battery. I was running this setup prior to watching this video and my advice is if you own BLHeliS esc you should definitely purchase JESC for them.

@slackerinmotion 4 года назад

Happy new year, Joshua. Thanks for all you have done for this hobby.

@zdm5290 4 года назад

Bought 20, set up my 2 inch filters better thanks to you. 48khz went from a pretty consistent 5 minutes of flight to up to 7:30 flying mixed. Fantastic.

@theuglycamel8122 4 года назад

I bought the JESC blheli-s firmware less than a week after 4.1 was released. Best 5 bucks I've ever spent!

@NunoFlyer 4 года назад

Me too, just 5 bucks, OMG!

@angrypepper3325 2 года назад

Thanks J.B. Your video and explanation is much easier to comprehend than other tutorials on the same subject.🤟.

@WhipGear 4 года назад

YES JB, It made a big difference... My quad feels way more locked in. Big thanks to all you guys especially you JB.... Love ya.

@oblazeo 3 года назад

I typically wait until I see the entire video to decide whether I'm going to hit the like button, but for this video, I hit it precisely 11:22 into the video. Also, more importantly, this is awesome. I am now running RPM on my 4-in-1 BLheli_s (bought it thinking it was 32). Thanks JB for this video and more so for 11:22. :)

@albertocagnin2108 4 года назад

Thank's Joshua, YOU increased my flight time, and also my 3 inch quad flight better !

@mike216ism 4 года назад

And some esc blew up. I wish I knew jesc dev created bidirectional D-shot or else I would have paid for it a long time ago. Another awesome informative video JB

@fprintf 4 года назад

This was really helpful! I'm currently waiting for the dust to settle on my own flying before investing but the local micro-quad group is super engaged in the debate and testing of JESC and likely JazzMaverick too. If I can get 30% more flight time per battery then $6 per quad (you have to buy 4 licenses for 4 ESCs) will be worth it.

@SinisterFPV 4 года назад

I paid for JESC. it is ABSOLUTELY worth it. Much longer flight times. Motors are cooler after ripping. Everything is just better especially combined with PMB 4.0 tune.

@MichaelHoughton_ 3 года назад

Hey Sinister - what is a PMB 4.0 tune? thanks for the help

@SinisterFPV 3 года назад

@@MichaelHoughton_ "Project Mocking Bird"

@matthebert007 3 года назад

On my Mobula 7 V2- I flashed with jazzmaveric just as you showed and I went from 2.5 mins to 3.5 mins flight time on the same packs in the same flight location under the same conditions flying the same way and drawing exactly 250mAh each comparison flight with cool motors to boot. So ~40% increase in flight time. BIG UP THANKS AGAIN JOSH!!!! YOU ROCK!!!

@Clif_Brown 4 года назад

I use JESC and really like it on 4 micro's so far, 2 whoops and 2 toothpicks. I use the 48Khz version and in all cases flight time increased and quads sounded smoother. A notable one was the Meteor65 with 0802 22000Kv motors. Best a 300mah could do was 2:15 of pretty fast house and outdoor (no wind) ripping. After JESC 48Khz, I am getting 3:30 for aggressive flying and up to 4:00 cruising on the same 300mah batts. I'm amazed by the change!

@OptiquevideoFPV 2 года назад

love how you change shirt throughout the video

@NextLevelCode 4 года назад

I setup RPM filtering on my mobula6 today. Holy crap it flies so much better.

@_NFE 4 года назад

Big hats off to Joe Lucid for the level of engagement he is maintaining with the community. That kind of support takes more time and energy than the creation of the code in many cases and he deserves a medal of honor for that.

@wrstew1272 3 года назад

Great explanation of why one would pay the developer for his work. Good man you are. Walking through the installation is great help for us non computer geeks. More like this.

@shotbyarian 3 года назад

thanks so much for all your videos! they are really helping me out with my pre built fpv quad to make it better!

@rotauq 4 года назад

I learned to fly on the iflight TurboBee77R and still is my favorite garden racer as it's so durable. I installed jESC (24k) on it a few weeks ago and was impressed how much smoother it flew. This 'power whoop' was way too powerful to fly indoors for me as a novice pilot, but suddenly i could with ease. I would describe it as the flight behavior being so much more aligned with the stick movement. Fly time increased some as less minor corrections seemed necessary.(maybe my skill level was improving as well) I recently updated it to the 48k version as well, and fly time really increased a lot without any negative effects. Not real benchmark comparison but whereas the original 4.04 out of the box configuration gave around 2.30 max(2S-520mAh), i now easily reach 4 min with the same battery.

@hateeternalmaver 4 года назад

I want it to fly good-er, yes. I heard of the free JESC but first opinions I read on it weren't good so I was waiting. Good to have your opinion on it.

@ShaunnStrydom 2 года назад

had my Cinewhoop Cvatar 6s for a few weeks, tried to enable bidirectional dshot, but motors just clicked with 100% errors. followed Mr Joshua's steps to update my BLHeli-s esc and the flight controller firmware, Used JESC firmware and payed him 5$. first time doing all this, Have an F722 FC with BLHeli-s esc, running Dshot600 now (8k - 4k) no issues. THANK YOU MR BARDWELL. I LEARNED ALOT

@slowentropy4531 4 года назад

I do hope people pay the small amount for the firmware. It's stuff like this they we need to support, not just by using and enjoying the benefits. But put something back in so our experience can grow and motivate talented people to put thier time in the make quads better. The future is bright if we think about the people making our quads fly so beautiful. Cheers from Dan

@TheMadmacs 4 года назад

ah oscar liang, i finally give in and search ''what is bi directional d-shot'' and there it is, an oscar page explaining what it is, thanks man.

@flyinphynixfpv5980 4 года назад

So, does this help ALL quads? Or only my 3 inch? Or my Cinewhoop? Or my micro toothpick? Thanks for the educational video JB. I've taken a break from quads and am amazed at the progress this hobby has made in 6 months.

@FAB1150 4 года назад

The RPM filter saved me! Today I hit a branch and broke a prop and I didn't even notice it. Really! It moved slightly but no crazy flipping like it did when I hit branches with no room filter. I did a flip with the broken prop, and only landed because I heard that the sound was a bit weird. Landed normally thinking something was stuck on the motor, and was really surprised when I saw that it was the prop, lol! The only thing is that propwash has gotten a lot worse, I am very new to tuning so I'll tinker a bit. Motors are freezing cold so I have a lot of room to tune

@JaraFPV 4 года назад

I bought 8 recently. I'm a developer too and I feel him. Some people just like free stuff without even saying "Thanks"

@jlarson42 4 года назад

I support Joe Lucid, bought the 20 pack for $20. More than fair price in my opinion. Rpm filters are working out great on both my blheli_32 and blheli_s kwads. Just ripped around with my Hawk 5 flashed with jesc and bf 4.1 A huge thanks to Joe Lucid for the work, plus Joshua Bardwell and UAV Tech for the knowledge. 💖🤓

@droneseyeview8327 4 года назад

Been thinkin about doin this to my hawk 5. Hows she fly compared to stock tune? I love mine already but very curious. Is the rpm filtering and bf 4.1 worth the upgrade?

@jlarson42 4 года назад

@@droneseyeview8327 so far I can tell you that it still flies amazingly well. My Hawk 5 was completely stock. I flashed the Hawk after testing rpm filters on my source one build and how well it works. Seems to handle flying with beat to snot props much better. All my kwads micro and mini are now bf 4.1 with rpm filters enabled. Happy flying.

@quadspeedfpv 4 года назад

As always very informative your videos are always a lot of help thank you

@VerbFPV 4 года назад

Good on ya for supporting the devs

@jr63 4 года назад

And indeed "I learned something" again....Thanks you!!

@juggalizzle75 4 года назад

Thanks for this! Definitely giving this a shot

@MarkusLutz1504 4 года назад

Bought 30 licenses so far - BRILLIANT for my whoops!!

@jimmycarr3368 4 года назад

As normal very good tips given. You know you can trust Josh.

@IanF-FPV 4 года назад

Working great on my micros. Quads have never flown better.

@alloutofdonuts3998 3 года назад

I appreciate the comments about the JESC regarding paying for the license. Perhaps people scoff at it, and/or assume it’s some greedy corporation lol. I could see it being a little expensive if you have like 20 kwads. But for the ease of it alone compared to jazzmaverick, it’s well worth the $6! lol’d at reaction to accidentally motor spin up heehee.

@jrminlinfpv 4 года назад

I’ve Tinyhawk freestyle,Betafpv 75Pro2,75X,F4 20A AIO FC. JazzMaverick,You have my vote👍

@partytimepplable 4 года назад

Thanks for all your help JB!! Link in the video description!!! Lmao I was alone seeing this video!! I thought i was hearing things!!!!

@docscarpetcleaning-sananto111 4 года назад

You beat me to it! I was uploading my guide tonight lol

@h2o-fpv623 4 года назад

I believe if they are doing work and the work they are doing is to benefit they should get their cut. Simple. Great video thank u.

@jamiecrump8979 4 года назад

THANK YOU THANK YOU THANK YOU!!!! You are a legend my friend!

@jodyking7278 4 года назад

Going to have to try this out.

@MG-ht2cy 4 года назад

I don't use the RPM filter, but I was so grateful for the 1.30min longer flight time with JESC 48khz that I bought 4 licenses directly. And when my Mobula 6 arrives here, I will buy 4 more licenses :)

@srossi88 4 года назад

For those who complain about buying JESC, to me, it's pretty simple. If you buy a blheli32 ESC, then you've ALREADY been doing the same thing, the cost is just hidden to you in the form of a higher cost ESC (remember that Blheli32 requires the OEM to license the software from the blheli32 devs). This whole argument of "I already bought the hardware why should I pay more..."....no you haven't. You bought blheli_s, which means you bought ESCs that do NOT support the developers of that firmware.

@rcrdps8144 4 года назад

I didn't really notice a difference with the rpm filtering, but the 48khz runtime rocks! And I used UAV Tech's super high whoop tuning pids,... which maybe wouldn't have been possible without RPM filtering,...so,....

@Sugar_K 4 года назад

another good reason to support Jesc is there is a V2 in the works that is a ground up rewrite and... will offer some substantial performance improvements over Blheli-s and maybe even the Blheli32 version.. for micros don't forget that Joe also worked out that the 48khz would improve ( massively ) flight times on really small motors with the reduction in back emf in the motor windings... no one else is diving as deep into motor and esc theory right now as Thorsten and especially if you fly micro brushless its well worth supporting his current and future endeavours

@tomnel 4 года назад

I agree that JESC deserves compensation for what he’s brought to BLHeli S. The implementation is what’s keeping me from buying. It’s tied to the esc which if it dies (and it will) that software is gone *poof* I go through too much hardware for it to be cost effective.

@JoshuaBardwell 4 года назад

With all due respect, I disagree with that argument. You saved $2 or more by buying a BLHeli_S ESC instead of BLHeli32. When a BLHeli32 ESC dies you don't get that $2 back. You replace the whole ESC. Same with JESC.

@michaelevans831 4 года назад

Please add this to your 4.1 playlist!!

@robertkempf471 4 года назад

Learned something today!

@NorthStarDrones 4 года назад

Thank you JB

@Politicallyhomeless957 4 года назад

I bought 8 firmware’s for my ESC’s from him 👍 it was like 8$

@friendlyfire01 4 года назад

I started buying 4-in-1 packs, bought two of those, then bought the 20 pack for my fleet. Well worth it!

@skirmich 4 года назад

Tinyhawk S with JazzMaverick´s 48kHz 16.77 firmware flies AMAZING with cooler motors and longer fly times.

@RCOverKill 4 года назад

I updated to rpm filtering on my 32 bit escs, and its amazing on the 1 quad its on. I have the 2 filter sliders all the way to the right, Im starting on the pids today, but it already flys great. I tried my best to get the motors warm, 2:30 seconds as hard as the battery would allow, and they came back ice cold. BF 4.1.2 has already made my acrobrat fly with warm motors that I couldnt tune before. Emax rs 1606/4000 kv. E max advertised them for heavy 3 inch, or a 4 inch., since Emax said they were to big for a 3 inch along with everyone else. Im looking forward to trying rpm filtering on it. It would be amazing if they come back cool, Ive tried on, and off for @5 months to get it flying properly, if it works on this one, Im sold forever, entirely!! Lol

@NunoFlyer 4 года назад

Cool.

@snowballfpv7583 4 года назад

Its 12 am 1st jan 2020 in the uk and this is my first video of the new decade 🎉

@aphinity 4 года назад

Rpm filtering and bidirectional dshot helped my 5” a bunch. Almost zero prop wash and so smooth. On my micros (2.5” mostly), it’s harder to say. Someone really should do a video focusing on tuning the filtering of micros with rpm filtering

@chrisgicky2215 4 года назад

Thanks Josh!

@cikwanfpv4646 4 года назад

Hai Joshua.. Im done do this to my micro 2.5 Turbobee 120rs 4s version.. Im do just like you say but im use JazzMaverick firmware, but all do right and i use Dshot300 perhaps before this i use Dshot600.. And after this i want to do RPM Filtering and i think iwant to be one of your patreon after this.. Thanks Joshua... You help me a lott

@edwright8279 3 года назад

Hey Joshua. I purchased a Nazgul 4s from Banggood USA with blheli s esc and it came with bi directional d shot rpm filtering installed and enabled. In the motors tab there were 0 errors and i have the filter sliders all the way to the right with all the settings you recommend. Motors come back not even warm and it flies amazing. Not sure why the esc came flashed already but apparently it did. Weird. Just thought I'd let you know. Thanx

@MysteryD 4 года назад

You know what I have learned in the past year of watching videos, learning how to fly, and owning only an SPRacing F3 FC in various frames? Every month there's some fancy new software or parameter that supposed to be SO awesome, and make your quad fly SO good. Is this all supposed to replace traditional PID tuning? Because I have basically a Wizard (in a much better frame about the same weight) with BF 3.5.7 and have tuned nothing bud PIDS and have been completely satisfied. I switched to Emuflight because it piqued my interest a bit, and, while it took a bit of tuning to get there, it still only flies as good as it did with weeks of tuning BF357 (with the benefit of about 30s longer flight times and ice cold motors). What it comes down to, for me, is why try to fix what you already thought was perfect? I'm not complaining. I just don't understand why everyone's so eager to reconfigure and retune their quads every three days.

@JoshuaBardwell 4 года назад

If you fly a 5" quad, the default can work well, but many people feel it can also be improved upon. If you fly a micro quad, nearly everybody agrees the defaults have a lot of room for improvement, and sometimes it's impossible to get a great tune at all. The goal of features like this is to make MORE people have YOUR experience of, "It flies fine what is your problem?"

@finndepury9013 4 года назад

Because it's fun.

@DroneShotFPV 4 года назад

It basically comes down to this, if you're satisfied with where you are, then leave it alone. Just like the old saying, "if it ain't broke, don't fix it". But, if there is a way to tune or enhance to the "nth" degree, and get just more performance, and you're like myself, or most others who LOVE to be on the cutting edge with cutting edge results, then go for it. I can guarantee you that when I first started building mini quads, when they were just starting to become a thing (I have been building RC crafts since the 80's with my father and blasa planes) that I was happy at that time with h ow they flew, thought it was phenomenal! I didn't change much as things progressed, because, as you stated, I was happy. But then I built a newer one with newer stuff, I was like "wait, this is amazing!" so I realized what I was happy with, was not actually the best it could be, but I was happy none the less. Then when cleanflight was introduced, same thing, etc etc etc, Rinse, repeat. When you get to the point of no prop wash, and smooth input and smooth steady results, it's all worth it, and feels even more amazing. BUT.... that being said.... you do not have to, and if you are happy with where you are at, then leave it, because truthfully you don't have to. I still have an original that I built was back, with Baseflight on it. It didn't see much air time back in the day as I didn't have a lot of flight time, and I tend to build a quad a week it seems, and it still flies (it's a dog compared to today's standards, but was once amazing!). So it's possible to keep what you're satisfied with in tact and be happy, but that is ultimately up to you!

@jackdaniels7913 4 года назад

Thanks as always! 🍻cheers🥃

@RGMGFitness 4 года назад

Joshua, would love to hear your comments on this new *FAA Remote ID Proposal* effecting everyone, down the road, who's flying UAS's. The formal publication was released yesterday (12/31/2019). Maybe you and the guys over at Rotor Riot could put something together. You've got a big voice in the FPV community and your support and views on this would be of value. I'm just getting into FPV myself and wondering what your thoughts are on this topic. Also, wanted to wish you a Happy New Years and thanks for everything in 2019..your channels been a big help in getting me started in the FPV game.

@SettekFpv 4 года назад

11:38 you can also hit the disable button when something like that happens

@GregQuillen 4 года назад

I'll pay. I like helping the little guy. I've clicked ur links to buy before. Wish I knew it worked for sure.. sometimes I click something to look at accessories then go back.. 😳😲

@SkyCandyVisuals 4 года назад

accidental click 11:20 whoa there lil micro lol thanks for the vid. not sure if this is necessary on the mob6 thats still on pre order i have coming but maybe ill give it a shot???

@techFPV5964 3 года назад

Hey JB i have a Mob6 and i was getting 2.5 mins of flight and i still had 61% to 66% left in my 300MAH pack and the whoop would drop like a rock so i did exactly what you did on this video and i changed the JESC to 48khz and in BF i changed to D-Shot300.Well i did exactly what you said to do in this video but the changes did not have any effect on the duration of flight or the percentage of the packs so basically everything stayed as it was when i purchased the mob6 3 weeks ago except now the jesc is updated to 48khz.What else can i do to increase my pack time? Thanks for the great video and I'll be honest with ya i have learned most everything i know from your videos including flying! so i thank you for all your time and efforts. I look forward to your reply and a FIX LOL!!

@gokartmozart9430 4 года назад

I might pay to do Jesc on my 5” but I went with the free version on my micros. It works well plus I dint want to spend $5 upgrading another happymodel AIO when just had a sailfly pop an esc

@fpvrc9829 3 года назад

Josh, i have a 3s crazybee whoop, ive just done the jesc thing, i was more than happy to pay the licence even if i couldnt get it to work, Joe deserves it. Ive updated bf to 4.2.1 and i cant change the gyro frequency,, theirs no drop down. the best combo i can come up with is dshot 300 gyro 8k ( cant change that ) and pid loop at 4k,. it did seem to fly ok at 8k/8k with dshot 600, but was a quick test just to know the esc is working still... in tasks its was well below that, the best combo was 8k/4k with dshot 300, tasks show the same... does different gyro and pid loop frequency cause any issues ? BTW love the tune on startup :)

@petrasignatavicius2176 4 года назад

I tried the free version 2 weeks ago, it didn't work (didn't arm when bidirectional dshot enabled), jesc worked.

@bluelinefpv559 4 года назад

That thumbnail though lol about to give this a try on my TH2.

@mach389 3 года назад

I’ll pay that no problem. As a matter of fact I just did. Thanks as always

@MrOrangeman18 4 года назад

jesc does work on the "l" version of esc's. you just dont have to buy licences for it

@tonyamendolara5515 3 года назад

I just updated my my esc,s to jesc dshot ,, I'm flying a 4" micro reverb, 1507 2680kv motors, on 6s..first I updated to 24htz,, my quad was flying like shit , motors were getting to hot no matter much I was moving the filter sliders around,, then I flashed to the 48htz,, what a difference, hardly any oscillation, and the motors are cool, hope this helps some people

@Sully365 4 года назад

been using 16.77 48K on the diatone gtr 349 for over a week and it's been amazing. I am curious why your other 3 motors showed 100% error. None of mine did once i plugged the battery in. Also...fun trick, you can figure out motor KV now from doing the math between RPM and Voltage reading at the top. My mamba 1408 4000kv motors are actually about 3850 kv after almost a year of abuse.

@JoshuaBardwell 4 года назад

I originally used blhelisuite to flash the ESC and when you flash with blhelisuite you have to click select file for each individually ESC instead of once at the beginning, so only the first ESC got flashed.

@Sully365 4 года назад

@@vermmaa i'm assuming you plugged a battery in? my startup tones for the ESC went up several steps in pitch after flashing either Jazz or JESC, but both gave me 0% error across all the motors when i was in betaflight with a battery plugged in.

@Tantago 4 года назад

@@vermmaa ever figure it out? mines all 100% and can arm just fine

@MattBalder 4 года назад

I had some trouble getting the JazzMaverick to work with the iFlight SucceX-E F4, 45A Blheli_S 2-6S 4 In 1 & BrotherHobby tornado t1 1407 4100kv. I did successfully get the ESCs flashed using the G_H_30_REV16_73.HEX (for my ESCs). When I got back into Betaflight I enabled the bidirectional DSHOT by using CLI command: set dshot_bidir = ON I also entered these two commands: set dshot_burst = OFF set scheduler_optimize_rate = ON The motors seem to be working normal and the error% in the motors tab was 0.00% on all. Before running those commands it seemed like the bidirectional DSHOT switch would keep turning itself off after save/reboot. Not sure why?

@Monolize 4 года назад

would you apply the same filtervalues on the meteor as on the tune you showed in your rpm filtering video?

@wrstew1272 3 года назад

As of this morning, setting up her new computer, it wanted to set up chrome. Surprised me.

@spoki_bones3656 4 года назад

Hey Joshua i was replacing a broken esc and I had forgotten that I used jesc for the old esc’s still on the quad. I flashed all the esc using jazz maverick and only got the new replacement esc to work and not the 3 other esc’s that had been flashed with jesc. Is there a way I can get my old esc’s to work in jazzmaverick instead ?

@robertpli743 Год назад

Hi Josh, I want to upgrade my BLHELI_s 30A ESC's to JazzMaveric firmware. But now the most current version is 16.9 with many subfolders (BB1_L, BB2_H, Beat, Official, RC) and again there subfolders to those folders. I have a 5 inch quad (modified version of Eachine Wizzard X220 V2 version with changed FC to Speedybee F7V3). Which version of JazzMaveric should I choose?

@KamilK3 4 года назад

11:18 now THATS why you take off your props!!! Imagine if it was 5-inch quad with props installed, JBs face would not be very pretty now

@DronieBoy 4 года назад

I been trying to get this to work with my teranix Qx7 and even though is binded it doesn’t move on the betaflight Reciber tab. Help please I haven’t be able to flight and I had it for a month. Any help please man.

@tome1271 3 года назад

nice on jb

@tokyo-re9nw 3 года назад

Hello Joshua, i have a brushless beta65 pro and am really confused about what firmware to use. Betaflight 3 will not work. Any suggestions? Thank you in advance

@highestvirtue1892 4 года назад

Hi Joshua I tried to reflash my ESC board with the hex file but somehow it seems my ESC board got wiped out. Is there a way to reflash it? Every time I connect to BLHeliS or JESC it says reading finished but no ESC info populates like before?

@dronecamps 4 года назад

LOL. Nice work dude. That Thumbnail made me laugh this morning. First thing I saw when I pulled up my RU-vid.

@barryfredrick2731 3 года назад

Funny, you're giving this dude props and he still attacks you bro. 🤦🏼‍♂️

@angrypepper3325 2 года назад

@@barryfredrick2731 It shows who the bigger man is.

@arcticqwadfpv5574 4 года назад

Thank you! -Can this be done to the Infinity stack you made on your Banggod5? (I folowed your build and made my own...)

@DroneShotFPV 4 года назад

You have to check your current firmware for the "H" as listed in this video and on the Jesc page. It's pretty simple to check, and if you have that H in the middle, you're able to do it.

@Realestitanes 4 года назад

Good video

@rawpicsfpv3516 4 года назад

Hey Joshua, If i reduced all my Filters as much as possible and my motors are 100% cool, can i do anything Else to improve flight Performance even more? Thanks!!

@Ammothief41 2 года назад

Is JESC still relevant? Haven't been flying in a long time, trying to get a quad put together from years old stuff. I don't mind paying to get the JESC firmware but I noticed this video is a couple years old too...

@cletussurfsalot7190 4 года назад

JB do you recommended the 48khz for 5” on BLHELI-S

@cyberoverkill5844 2 года назад

I flashed the ESCs on BLHeliConfigurator but I'm not seeing the "Error" readout on Betaflight? Mob6HD, same O-H-5 settings as video.

@nivofpv 4 года назад

HELLO JOSHUA..i have bought 4 license and i instaled it..BUT one of my escs i accidentally burned it.. so i replace it but now i cant install the telemetry..i have 5 licenses the esc is activate but the configurator doesnt let me to flash telemetry..now what can i do

@WINTERACTIVITY 4 года назад

What if the bi-directionnal switcher in betaflight 4.1 or 4.2 doesn’t want to be saved as enable. Even with esc last version blheli32.7. Such a nightmare with my Tmotor F4!

@JoshuaBardwell 4 года назад

Are you certain you are on a released version of Betaflight 4.1?