BMW E82 135i Valve Cover DIY | Full Bolt-On Series (Episode 4)

Подписаться 1,3 тыс.

Просмотров 6 тыс.

50% 1

It wouldn't be a BMW if it doesn't have oil leaks. The valve cover is a major area prone to oil leaks in BMWs. In this 4th episode of our E82 FBO series, we replace the 135i's valve cover with a brand new one to prevent oil from leaking after going full bolt-on.
BMW E82 135i Full Bolt-On Series Playlist: • E82 135i Full Bolt-On ...
Instagram: @drive_wrench_repeat
135i Genuine BMW Valve Cover Kit: www.fcpeuro.co...
----------------------------------
Track: You
Artist: Sappheiros
Watch: • ❰Progressive House❱ Sa...
Download: fanlink.to/chfk
----------------------------------
#BMW #E82 #135i #N55 #valvecover #valvecoverdiy #valvecovergasketdiy #valvecovergasket #N55valvecover #N55valvecovergasket #135ivalvecover #135ivalvecovergasket #fcpeuro #FCP #FBO #M2 #M2Competition #M2C #drivewrenchrepeat #DWR #S55 #alpinewhite #hockenheimsilver

Опубликовано:

8 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 33

@DS-ec6lt Год назад

Your video was really useful for me. Probably one of the best on RU-vid. Very clear and informative with info on tools needed. Doesn't get better than this. One possible stumbling point. That torx bolt holding the stress bar could be torqued really tight. I had to use a long (48" 3/4" breaker bar) to crack mine. I also can't believe what BMW charges for the valve cover knowing that this is a common failure point. Thanks again for the helpful video!

@drivewrenchrepeat Год назад

Thanks for the recognition and mentioning the stumbling point! Will pin your comment so that others can take note as well.

@DS-ec6lt Год назад

One question, how did you get the cowling to budge so that the back of the valve cover can clear the valve components? I notice when you did the final pull the cowling lifted a significant amount. Did I miss that in the video? Thanks!

@drivewrenchrepeat Год назад

@@DS-ec6lt We removed the cowl entirely (watch from 3:30 to 5:10). If you're referring to the 'other cowl' being lifted at 26:55, we didn't loosen it or remove any bolts iirc - just a bit of brute force to remove the valve cover.

@DS-ec6lt Год назад

LOL!

@an3ony Год назад

Just did this yesterday, without this tutorial, I"d have been lost. Thanks very much for posting this.

@drivewrenchrepeat Год назад

Glad it helped!

@deancameron8378 Год назад

@drivewrenchrepeat Great tutorial i used this guide for my install . I used the FCP Euro parts list your provided (used Elring valve cover instead of oem ) and and was able do the install over the weekend(did new coils and plugs also). i cheaped out and did not buy a new vent hose (and of course my old one broke a clip while removing .) The one step i changed was removing the 6 connections for the fuel lines on the valve cover side and removed the entire fuel rail with the lines in place.. This gave a little more clearance when reinstalling valve cover and also allowed for easier install since i did not have to reinstall the fuel lines one by one. PSA be very careful with removing injector clips as those can also be a pain in the arse to remove without breaking

@drivewrenchrepeat Год назад

@deancameron8378 So glad you were able to get this done with the help of our video. Also appreciate sharing some tips and insights for the audience as well.

@JL-pq4rl Год назад

I just did this yesterday and replaced to replace the valvetronic motor. Since I was already in there, swapped out plugs and the gasket. Props to you for recording your progress as this took me 9 hours total, alone, without a camera.

@drivewrenchrepeat Год назад

Kudos to you for taking the time to do this yourself! You must've had quite the sense of accomplishment afterwards

@deancameron8378 Год назад

Last comment i would say for actual removal and install .. have a buddy . cracked my old one when trying to remove on my own .. there is a section (middle bolt section on the firewall section of valve cover is somewhat hard to clear without another person holding the remaining plastic near the fire wall ). that step helped me a great deal on install. When torque down the bolts for the 1st time i notice other bolts go loose (thats the valve cover getting seated I assume ) so I torqued them in order three times and by the 3rd time all was well .. hope this tip can help others

@victoriol Месяц назад

Thanks for this video. I bought a 2010 135i a couple mounths ago, and Im will be doing this and sparkplugs. It is a lot of work to repleace a valve cover gasket. I think I will miss how ease was to work on my old nissan SR20 engine, but I like my 135i a lot!.

@griffindetracy6312 Год назад

This is great work! I love the effort and time put into this video.

@drivewrenchrepeat Год назад

Thanks Griffin! We appreciate the recognition 🙏🏻

@sam10mix 4 месяца назад

This video definitely helped me out a ton thank you for sharing my car is happy now!

@GutoFontana Год назад

I ended up removing the wipers and the cover too to better access no needed but made it easy for me. 10 year old plastic, broke some clips and the crankcase breather hose just disintegrated ahahahha anyway thanks.

@drivewrenchrepeat Год назад

Right on!

@kid2519 Год назад

One idea is to put a towel over the latch just in case if the trunk falls, it won't close.

@drivewrenchrepeat Год назад

Great tip!

@vampiremoonburn Год назад

Thank you for sharing, I have an aluminum valve cover from Amazon for my N55 135i and I'm saving this video.

@keeblertime1486 5 месяцев назад

It takes less than 5 minutes to take that wiper cowl out of your way instead of fiddle fucking around with it and risking breaking anything or rolling the gasket. Literally comes out and goes in like butter when you get that out of your way.

@stephanelouvet1113 Год назад

Nice ! Lots of info there as I'll have to replace this seal on my E92 N55. To what I see, your engine bay is very very similar if not identical (just a tad smaller than my 3 serie) Thank you.