Bolt Strength check FEA simulation- Bolt Pass or Fail using solidwork simulation 

Complete and great toturial. 🥰

Excellent!!!!

Thanks for the tutorial

Thanks

Thanks for sharing

Exellent!!! thanks...

Hola, buen video. saludos de lima, Perú

Hello. Great tutorial! What if the bolts are already there? I mean during the assembly I fastened it using the bolts from the toolbox. Do I have to remove all the bolts from the toolbox and do the same steps as you did in this video? Thanks

Ihave a trouble with bolt conection in solidworks simlation. i have a countersunk bolt. Head of bolt is a square of 29mmx 29 m and draft on 5 degree. Head of bolt has a thickness of 25mm . It's not an option in bolt connection bescase i can't choose 4 surface of head bolt for set contact. How can i use type of this countersunk bolt in solidworks simulation!. tks a lot.

Its gud for bolt load tasting but structure is before failure for bolt.....

i have a question, what if i beam is bolted on both sides? Does it cause tensile stress due to bending moment? or just cause shear stress only?

Keep shaking my head for half an hour LOL.

could you help me with simulating snow, wind and gravity on a welded truss arch? is solidworks simulation up to the task?

what's the music ?Can u tell me?thx

How to test if connection is by welding method.

what is 1.5 in strength data means?

Did the bolt fail or just approach its yield strength (by the way, which yielding criterion was used?)? There is no damage or failure criterion in this simulation, not mentioning plasticity... 1) How can one state that something has reached failure without setting the above conditions? 2) What about mesh effects (I do not see any mesh here...), stress concentration? 3) Simulations without minimal validation, mean nothing. 4) It has not been a great idea to embed FEM into CAD software. This is the end of real Engineering and of Engineers who think that Engineering Design is about drawing.

I have homework about this, but my professor does'nt really have a knowledge about this, so maybe I will do simpler simulation haha

When i try to set up my fixture, i selected the beam surface and it shows "Load/Restraint cannot be applied to the beam face, edge or vortex". How to solve this problem ? and i notice why the object you designed earlier with the base is not shown during the simulation. The beam that sticking out also change its place to the middle of the main beam. I think u have change different CAD files for this video

There are not bolts under compression streght. All are under tension, becase lower bolts can't be compress it by itself. The are not other elements trying to compress it. Maybe, tension could be zero, but no negative (compression). On the other hand, compression is present between vertical flange and the lower sector of horizontal beam attach plate.

how did you define the preload

how to sync two circle example:- one circle dia75mm and secound circle dia1000mm dia1000mm (1000mm-100mm=900mm) so change dia 75mm change (75mm+100=175mm) mins i one circle dia minuse so secound dia pluse is value how create बहुत बढ़िया पर मुझे ऐसा काम कुछ इस तरीके से करना हो तो कैसे करे कृपया बताये जैसे के एक circle 75mm dia का हे और दूसरा circle 1000mm dia का हे अगर में इन दोनों में से किसी की भी साइज़ बदलता हु तो वो एक दुसरे में pluse minus खुद्ब्खुद हो जाये जैसे के अगर में 75 mm dia में 25 mm जोड़ता हु तो वो dia 100mm हो गया पर जो दूसरा dia जो 1000 mm का हे वो 975mm खुद्ब्खुद हो जाये बस ऐसे कोई भी एक dia अगर pluse होता हे तो दूसरा dia खुद्ब्खुद minuse हो जाना चाहिए और कोई भी एक dia minuse होता हे तो दूसरा dia खुद्ब्खुद pluse हो जाना चाहिए हा पर जितना हम pluse या minuse करते हे उतना ही value एक दुसरे dia में pluse minuse होना चाहिए कृपया करके ये बताये ये कैसे हो सकता हे solidwork में ?

The horizontal ribs at 15:37 are meaningless, because lead to breaking of the wall plate out of profile. The ribs must match the profile ribs.

Can you upload your files sir?

Do the twin towers and building 7...

yeah go ahead and mute this one

please remove the excess ads.... 10 video ads is a little ridiculous.

36 minutes of the same music!

sound ..please put mute..

Can you please turn off your audio background? I think we are not interested in your music !