Breakthrough Suppressor Cleaner

Подписаться 2,8 тыс.

Просмотров 8 тыс.

50% 1

Breakthrough Suppressor Cleaner, 1st time using it and liking it so far. Silencer is a new ‪@DeadAirSilencers‬ Mask and has a little over 600rds. through her. Thought the cleanser did quite well and curious how well it'll do after a 1000rds.

Опубликовано:

26 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 40

@filfarmerpacnw4868 15 дней назад

I used wipe-out bore foam and it cleaned my baffles in about 1hr. Put the baffles in an empty mayo jar and sprayed the foam in. Stirred it around about every 15 minutes adding a touch of foam as it got low. Came out 95% clean and a bit of wiping finished it.

@Keep_It_Loaded 14 дней назад

Oh nice

@quiettime6871 Месяц назад

Good tip on the ziplocs. I'll use an old spaghetti jar

@Keep_It_Loaded Месяц назад

Lol, I use a Mason jar now. It just lives in the garage for whenever needed now.

@quiettime6871 Месяц назад

@@Keep_It_Loaded thanks for posting. I just grabbed a gallon from the amazon

@pittwm 6 месяцев назад

I’m using it with ultrasonic cleaner, it’s like magic

@Keep_It_Loaded 6 месяцев назад

Oh nice

@pittwm 6 месяцев назад

@@Keep_It_Loaded I tested it with an old mule Gemtech Outback. It literally melted all the lead, I couldn’t believe it. My take away is it works magically on non aluminum cans, the ti baffles looks brand new after it’s clean. Aluminum baffle stained a little but I guess that’s as expected.

@Buletspunge555 6 месяцев назад

Any feedback on how the solution reacts to anodizing when used with sonic cleaner?

@pittwm 6 месяцев назад

@@Buletspunge555 okay, let me preface that the Outback (full aluminum with updated ti and alloy baffles) was F up previously from Simple Green in Ultra sonic cleaner. Some of the anodizing was gone. This new stuff I dipped both tube and baffles and let soaked for 12 hours and ultra Sonic it twice at 10 minutes cycle. There is some lightening of the finish but I’m not sure if it’s from previous simple green or this stuff. I THINK the tube’s anodized finish would’ve been fine if I just soak and scrub in this solution. The to baffles came perfectly like new and the alloy baffles all free of lead and carbon, but a bit stained. I have no complaints since I use the Outback a lot.

@Buletspunge555 6 месяцев назад

@@pittwm thanks for the feedback friend! I've got a SiCo sparrow on the way, and I'm doing prep homework ;)

@filfarmerpacnw4868 15 часов назад

I used DIP today for 5hrs and the baffles came out 98% clean. Next time I will do overnight. I used a quart canning jar and lid. Mixed 2 cups 5% vinegar and 2 cups peroxide. You could see the scrubbing bubbles eating the lead off. Just wear PPE and do not get liquid on skin or breathe fumes. It makes lead acitate when disolved. Keep warm as it works better when warm. Maybe in a warm oven or warm pot of water (125f).

@Keep_It_Loaded 15 часов назад

👍🏼, never tried dip

@rickperry411 17 дней назад

Is Breakthrough safe for Aluminum baffles?

@Keep_It_Loaded 17 дней назад

Yes. Aluminum, stainless steel, and titanium.

@code_red7744 7 месяцев назад

Mask can go way longer between cleanings. I think it says 2000 rds in the manual …Look into “anti spatter nozzle shield spray” you’ll be able to wipe the baffles clean with no effort if you pretreat and spay a little before you go shoot ,it’s mind blowing seriously.

@Keep_It_Loaded 7 месяцев назад

One of their recent videos says around 1500 but have stated they have seen more. I just wanted to test the cleaner. It's one we got in at work and rather have 1st hand experience when asked.

@Keep_It_Loaded 7 месяцев назад

I'll have to look that up, never heard of it

@russream3732 Месяц назад

I waited 1100 before the first cleaning 😂 of my MASK. A wooden stick became my friend in getting the baffles out. So I clean now at 400 - 600, and white lithium grease everything - my life is much more enjoyable. ❤. 22Lr is what it is.

@Keep_It_Loaded Месяц назад

Lol, I'm almost to 2000rds to test out Boretech Silencer cleaner

@russream3732 Месяц назад

@@Keep_It_Loaded please post the cleaning. I will be interested to see your results - thanks !

@stevenshewfelt888 3 месяца назад

ok once you get all the carbon off and its now dirtied up the solution, how do you dispose of the solution once done?

@Garbonzobeanandblackbeans 3 месяца назад

Neighbors yard

@Keep_It_Loaded 3 месяца назад

You'll need to seek your local laws for disposal of "household hazardous waste". My location shows to dispose of at my local HHW site which is located at my local dump.

@madbroindustries 2 месяца назад

I want to buy this stuff but idk if it will damage my finish. I have a YHM R2 and a JK armament goat

@Keep_It_Loaded 2 месяца назад

Yeah, the material of both of those are safe, but yes, you couldn't soak for any extended period without the risk of losing or wearing your finish.

@x3dominator28 5 месяцев назад

.22 is easily the dirtiest suppressors to clean. My 9mm and 45 acp cans are basically cleaned once every few years….

@Keep_It_Loaded 5 месяцев назад

Agreed on both parts. Hoping to re-due video again either at 1500 or 2000rds. Currently sitting at 1200. May due testing with Bore Tech brand though to further my testing with that Brand.

@shanevmax34 6 месяцев назад

Wait until you graduate to a 9mm can. I had to put mine in a vise in order to disassemble. Soaked it all kinds of aluminum safe solutions. Still have carbon build up. I used brass brushes. I now understand why folks throw away mufflers and install new. If the gun muffler laws in the states were different.....

@Keep_It_Loaded 6 месяцев назад

Did my Surefire Ryder 9 also but with a different cleaner for testing purposes. I personally am not the biggest fan of aluminum baffles.