Thanks for watching! Comment your thoughts below. Overkill? Or just right? This is a long one with multiple steps SO time codes are posted in the description and chapters are added in the video progress bar. Please subscribe if you want to see more DIY Projects and “like” the video if it helped you out! Thanks!
You probably dont care but if you are bored like me during the covid times you can stream all the latest movies on InstaFlixxer. Been binge watching with my brother recently =)
Mail carrier mailbox wish list: 1) Larger box. 2) Numbers on the side approached by mail carrier. Solid construction for a small mailbox tho! That's appreciated, that it will not wobble when you open/close the door.
Sounds like I need to bite the bullet and out numbers on the other side 😬. Thanks for all the work y’all are putting in right now! I saw the postal truck roll through my neighborhood at 9pm last week - so I know the hours are brutal with C-19 holiday season
@@AndrewThronImprovements If you ever do mailboxes in the future, having the numbers on the box itself is the best place. Put them on when the flag is down so the flag doesn't cover them. The reasoning is that snow plows can push snow to cover the numbers when it's not on the box. Also, grass, vines, bushes, and vegetation can cover the numbers on the pole. Also, the big white stickers with black numbers are the best. The biggest mailbox out there only costs $60-$80 depending on the vendor. The amount of time you save the postal workers over the lifetime of the big mail box is WONDERFUL.
This is baddass and absolutely NOT overkill, but very slick and classy! I've been wanting to redo my mailbox for years and this design is perfect! Thank you for sharing your knowledge with us internet peeps!
That's a terrific looking mailbox. My M. Box was changed thrice in two months. Local 'citizens' sped past on my curved lane and took out my expensive wrought iron box! I ordered another and two weeks later my neighbor backed into it. Patience is my fav virtue but was tested greatly. My first 2 M Bs cost $200 + each; the 3rd is made of a thick stainless pole driven 30 inches down embedded in more concrete and rebar than you used. The next guy who hits me, will take out his own bumper and lots more too. :) I like yours; its so you. Thanks. Back to my ATI marathon.
Out in the country mailboxes get nailed often. I would make it out of concrette with rebar , BUT, mount it to a large coil spring like from a vehicle suspension with a 48" deep footing in the ground. The coil spring allows it to bend over and stand back up when hit by maintenance equipment or a vehicle.
Super nice. I actually live in a neighborhood where the mailboxes used to be a feature for the neighborhood so when somebody has a crappy mailbox and doesn’t want to spend the $500 to $600 that a lot of people have, this is a great solution
Appreciate the support! And definitely something that can be done with scrap wood to keep costs down - just takes a bit of time to put it all together 🤙🏻
Your mailbox turned out great - I think I’ll build something similar. Waiting for the bent cap board before cutting the curvature does seem like the better approach as you mention. Thanks for that. I appreciate you internet stranger! Hah
I like the herringbone tile pattern in the half bath. I will check that out too! I appreciate this video for it is helping me with my own mailbox project in progress to use bamboo in this same style. Now that is over kill?! LOL but yours is most modern and a good idea. I especially liked the bending of the wood processing.
Beauuuutiful mailbox. . .gonna ask Hubby to make this for me as a Mother's Day gift 😉 thanks for sharing and making this video fun and easy to follow 😊 Shalom & Blessings
Excellent production that made watchin this video more interesting. And it's definitely not over overkill. In fact, I thought you'd incase the post in an above groun d concrete slab. That's What I'll do when I recreate this look in my front yard. Thanks for this original idea. Love how you just used things "layin around the house" in your project. I'm the same way.
My mailbox is a 3.5" metal pipe that is 1/4" thick. Inside the pipe it's filled with concrete and a run of rebar. It has rebar going through the pipe to prevent it from pulling out or bending. It has a reflective sticker on the side to prevent people from running it over but if they still manage to hit it, it'll for sure destroy their car. I had my mailbox ran over twice and they just left the area. Next time they won't be able to drive away. That's the plan at least.
I know this is a two year old video but I am looking to update my mailbox and this unique design really caught my eye. We have snow plows that come by regularly (ish) in the winter though and I'm worried it would get beat up. Do you have snow plows where you live?
I really like how this turned out, but shouldn’t the house number be on both sides of the base? When the UPS guy comes down the street, he can come from either direction, so I’d like him to be able to see my address. Same with friends coming over for the first time. They might drive on by and only see the number when they turn around and circle back. And if it’s JUST for the mailman….ours comes from the other direction!
Andrew, great work. It is not overkill by any means. Just getting into woodworking. Building my workbench as I am typing. I will definitely like and Subscribe. I will be stealing your design. LOL This is going to be my first project once my workbench is completed. Thanks
Although I have way too many projects to complete that I couldn't dedicate that kind of time to a mailbox I have to hand it to you for your imagination and skill. 👍👍
Great design. Fancy but not too fancy... which is what I'm going for. I was planning a similar design, but may adapt closer to yours. One thing I noticed, because I like the black between the slats, is that you skipped the part where you added plywood backing to the slats.
Andrew, I hope you still receive notifications for this 2 yr old video.... do you have any lessons learned from the project? I'm going to copy yours!!!
Hey David! If I was going to do this again, I would bend the picket FIRST. After bending it, I would then use it as a guide to scribe the cuts on the 1”x6” lumber. That way, you won’t have that caulk gap like I did. Hope that helps!
@driver1928 Thanks for watching! I had that one set of house numbers on hand so I just went ahead and installed them on the “incoming” side of the road. The other direction is essentially just a cul de sac, so 99% of traffic will see the numbers as they drive up. BUT I probably should just do it “right” and add #’s to the other side for consistency. Part 2? 😂
Hey, thanks for video, looks great. You mentioned that you wish you had cut the 1x6s AFTER establishing the curvature to prevent that gap. How exactly would you do that?
Hey Peter - I would probably bend the front face (picket) first and see how much curvature I could get. Then I would scribe that curve along the 1x6’s. Hope that helps.
It's a bad shame I don't have your texting name or email, but I guess we'll leave it at that, but what I can do is this, I have a close near by hardware store that has a lot of home stuff, and they also carry mailboxes, and I did find a mailbox that is 24"l x 12" W x 15/18" h, and it was $62 ,I have a ballpark idea in my mind of how I'm gonna make it, I'm just hoping I can get it done in the near future
Class A job, a good mailbox is never over kill, last time that I checked, mailboxes are for a reason, they should all be fort Knox fortresses, but then people should think the house they live in,
Hi! No supply list, but from memory: 1. 4"x4"x8' pressure treated 2. 1"x6"x16' pressure treated 3. 2" exterior deck screws 4. 5/8"x6" pressure treated fence picket (for the bent front face) 5. Exterior wood stain, house numbers, and mailbox Thanks for watching!
A good mailbox job is never over kill, think about it ,the word, fortress says exactly what it means, FORTRESS, we are given the privilege of using or having a mailbox from the government, and then they put regulation on the ground post, and we all know that's bullshit, so then a close friend of mine said, put it up the way you want it, and that's what I plan on, 😎🇺🇸👍
people dont realize it's mandatory to have house number on the mailbox or in front of their house. it's ridiculous looking for their house when they have none. just imagine when they have friend/family looking for them or when they need urgent care? nope cant find your house, i'll keep going.
This may be fine for in a neighborhood, but if someone builds this and installs it on a Highway they will get a nasty letter from the Postmaster. This has more material than is allowed and also exposes the property owner to a lawsuit if anyone is injured if they hit the mailbox and it does not give way. There are guidelines that must be followed. Google mailbox requirements and be safe
There are a lot of ideas with the mailbox idea, it just depends on your residential area and your road way of traffic, are your road curves rather close or far enough way for the motorist hopefully isn't intoxicated or the isn't road slickin with snow or rain, or their just not watching their driving, but you have to consider, regardless of how sober they might be, a true idiot still can't drive a straight line, so then your still at the mercy of Gods hands and his mercy, and yes, we're all at the mercy of government regulation, mailbox damage rarely ever involves any motorist not walking away, I'm rather sure we can all go heavier with the base of our choices in the foundation, but the government regulations give the vandals way too much play room, until they get caught, and if mailbox vandalism is a 1,2,3 count of jail time, then they might face prison time, but the difference between vandalism and motorist having an excusable or inexcusable accidents with mailboxes, sometimes it's just hard to say, but putting up a nice mailbox, the ideas are unlimited, if you want fort Knox go ahead, but it still has to have a safety brake away,
