Welcome back, folks! This time we make an Arduino-based RC Flying wing out of foam, with 3ch of 2 servos and a brushless motor on board, no extended fuselage or tail, simply a cool flying wing! As this is an intermediate-builder project, it may require that you have some background knowledge of using an Arduino board, and some basic knowledge of electronics.
Hang around until the end of the video to see whether this thing can fly!
Thanks for watching! If you enjoyed watching this video, kindly give a thumbs up, share, comment, and a subscription to the channel to see more similar content.
----------------------------------------------------------------------
👉 Visit my online Storefront: sites.google.com/view/maximag...
----------------------------------------------------------------------
☕ Buy me a coffee: www.buymeacoffee.com/MaxImagi...
----------------------------------------------------------------------
Instagram: @max.imagination - max.imagina...
Instructables page: www.instructables.com/member/...
----------------------------------------------------------------------
Disclaimer: Amazon purchase links below are affiliate links. It doesn't cost you extra to buy through those and I just get a tiny commission. Thank you!
Before recreating the plane, (if you are to choose an Arduino flight controller setup like my own) check out my previous video which shows how to make your own RC Arduino 7-channel Transmitter:
- • Build an Arduino Radio...
Circuit diagram - Receiver/FC (credits to Electronoobs) - electronoobs.com
/eng_arduino_tut25_2.php
Codes - TX & RX NRF24L01 Arduino plane codes - drive.google.com/drive/folder...
Learn more about the NRF24L01 Transceiver - howtomechatronics.com/tutoria...
Blueprints of the foam flying wing in PDF - drive.google.com/file/d/1WAnE...
Flying wing design with measurements & CG location - drive.google.com/file/d/1JoqF...
Center of Gravity (CG) calculator website - fwcg.3dzone.dk/
Purchase links to parts used in the project: (Parts count ("x..") in reference to the quantity required, actual purchase quantity may vary)
(x1) Brushless Motor 7000Kv 1-2S EMAX - amzn.to/3JJqwch
(x1) Plane propeller 5" - amzn.to/3vQivN4
(x1) Brushless Electronic Speed Controller (ESC) -
amzn.to/3zJHMtt
(x1) Arduino Nano board - amzn.to/3dizYqW
(x1) NRF24L01 100M RF Transceiver module - amzn.to/3BQzKSn
(Optional) NRF24L01 + PNA + LNA RF Transceiver module (longer range) - amzn.to/3JEoOsV
(x1) Voltage Regulator 3.3V AMS1117 - amzn.to/3JGJxMu
(x1) Perforated Prototyping board 3x7cm - amzn.to/3Pa6GIA
(x2) Servo Motors 9G - amzn.to/3QyORDQ
(x1) Li-Ion Battery 7.4V 800mAh (Higher capacity, same weight as battery seen in video) -
amzn.to/3dj3oFn
Female & Male Pin headers - amzn.to/3Qej2Rg
(x1) 5mm Posterboard foam core sheet for fuselage & wing tip fins 12x9" - amzn.to/3BYqFXP
(x1) Styrofoam (Polystyrene) insulative foam board sheet for the plane - 1.5"
(x2) Paperclip
(x2) Mini zip ties
Clear tape - 2" roll (for Lamination of the wing)
Kapton tape (used to make 6 sporty stripes)
(x2) Wooden dowel - 5mm stick
(x2) Bamboo Skewer - 3mm stick
(x4) Popsicle stick
0.25mm Nichrome wire (Hotwire tool)
Simple wooden bow-shaped frame (Hotwire tool)
(x1) Self-threading wood screws (Hotwire tool)
(18 AWG or thicker) Enameled wire (Hotwire tool)
(x1) Small retraction spring
(x1) Pushbutton momentary switch 3A
🪛🔧🔨 Tools and extra supplies I use:
➡️ Soldering Iron Kit - amzn.to/3X6L5Wq
➡️ Hot Glue Gun - amzn.to/3E6trJG
➡️ Drill Machine - amzn.to/3EDe0u8
➡️ Box cutter/Utility knife - amzn.to/3hP9MGI
➡️ X-Acto Hobby Knife - amzn.to/3XbL7ML
➡️ Cutting Matt (Green) - amzn.to/3gil71A
➡️ Needle-nose Pliers - amzn.to/3ECTKc3
➡️ Wire Cutters for Electronics - amzn.to/3ECut1B
➡️ Wire-stripping tool (Automatic) - amzn.to/3hQsMVD
➡️ Screwdriver kit - amzn.to/3V6vgNX
➡️ Heat-shrink Tube Kit - amzn.to/3AksTPE
➡️ Jumper Wire Kit - amzn.to/3UGhMZq
➡️ Breadboard for Prototyping - amzn.to/3GlF4ze
➡️ Perf Boards, Pin headers, and Connectors Kit - amzn.to/3AkySUw
➡️ Superglue - amzn.to/3EE6uis
➡️ Duct Tape - amzn.to/3g5mTU0
➡️ Double-sided Tape - amzn.to/3Edta82
➡️ Kapton Tape (for battery leads) - amzn.to/3X58bNl
Music credits:
Song: Kuty Boi - Beachside Babe
Video's Link: • Kuty Boi - Beachside B...
Song: ELKAA - Ocean
Video's Link: • ELKAA - Ocean [Free Ch...
#arduinoproject #flyingwing #arduinonano #maximagination
10 авг 2022
