Building a 350 Small Block Chevy Start to Finish - Part 1

Подписаться 23 тыс.

Просмотров 267 тыс.

50% 1

Starting off this 350 SBC build, by putting together the short block. In the next couple videos on this 350, we'll show putting the rest of it together and will be starting it!
Other videos we have on 350 small blocks:
63 Impala overheating issue - • Traveling 350+ miles t...
64 Impala 350 SBC overhaul - • 350 Small Block Chevy ...
Random videos you might enjoy:
68 C10 body work - • The fabrication just D...
65 Nova LS3 wiring - • Wiring the LS3 - Chevy...
Here at ZHP garage, we do it all. Tune in every week for a look into our custom builds, arrays of car shows we attend, general service/how to videos we make, and multitude of races we participate in. We have over 25 years of experience, and can work on anything from the daily commuter, to a custom fabricated roll cage, to a custom Chevy C10!
For behind the scenes action, more look into our builds, and things not shown in the fully released videos:
Follow us on Instagram:
Camera Man: / rhziggy
Master Mechanic: / zhp72
ZHP Garage: / zhp_garage
Give us a like and check us out on Facebook:
ZHP Garage Facebook page: / zhpgarage
#zhpgarage #350sbc #fullbuild #smallblock #enginebuild

Опубликовано:

5 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 151

@sunkbootnoot1204 2 года назад

I'm buying a block with pistons for 75$ this video will become handy I've never built an engine in my life

@bentbarrelballistics6894 Год назад

Better check the block to make sure it's worth building

@isaiahogunshi3969 Год назад

@@bentbarrelballistics6894how do you check

@itsaj4976 Год назад

How's the build going

@nerdsofthefist Год назад

Yeah how’d that go?

@brandonlozano7401 9 месяцев назад

@@nerdsofthefistprobably never happened

@trymilion Год назад

I'm going to have to take apart and rebuild a 350 for my gfs mom's 91 s10 soon so these vids will 100% come in handy

@Swervy57Squad57 Месяц назад

That’s what I have and am currently contemplating LS or SBC. I think I’m leaning toward SBC swap more but I know absolutely nothing about motors

@corolla-zj9wq 2 года назад

Ahhh don't worry about the dirt! Its just its daily dose of vitamins and minerals

@StationaryNomad361 Год назад

Thank you SO MUCH for these videos! This is exactly what I’m looking for. The detailed explanations are so valuable for us beginners

@ralphnolan3187 2 года назад

Built my first 283 when I was 19 by myself good engine

@hydroy1 3 года назад

You do it very much the same as me, everything must be clean, clean, clean !. A few things I now do, rather then use assemble lube on the piston skirts witch can't really get into the ring lands where you need good lubrication on first fire up, I use to submerge the pistons & clocked rings in a tray of 30 weight oil, witch does work well, however my machine shop told me nowdays they use WD40 spray and just spray the pistons & rings real heavy, then pop them in the bores. Then to stop any contact of the rod bolt threads coming in contact with the rod journals of the crank I use 2 pieces of 3/8s fuel line on the threads of the rod bolts to protect from damage to the crank or threads of the rod bolts . I also put a good shot of oil on the inside of the piston pin (both sides) and work the piston all around to lube the pin area, a common issue for SBC with press fit pins. Building my 67 Chevy fresh bored.030 over 327 in about a month with new everything & Molly rings.

@fdsengineeringelectricalse253 2 года назад

Thanks guys. Just finished the bottom end of a 350. You guys do it detailed and practical.

@stephenfaulkner1448 2 года назад

Good that you mentioned not to put the plastic gauge next to the oil holes. I did that once and the gauge wasn’t even crushed.

@RALPHD099 3 года назад

definitely gives me the confidence to do muy own… great step by step, can’t wait for part 3…!!! i already watched 2…

@SeriousSchitt Год назад

It certainly gives me great confidence to be able to do ‘your’ one too! I can’t wait till part two, I’m about to watch it now.

@timothygleason6925 2 года назад

Thank you, I appreciate teaching me what I need to know about it. And I look forward to the part 2, that comes after 1.

@ZHPGarage 2 года назад

No worries, part 2 is already out on our channel.

@MaxRCandMoto Год назад

absolutely love the gym equipment in background. shows you can do it anywhere

@lukecoonrod 7 месяцев назад

I think the guy on instagram doing it in his dorm room wins

@pumasisneros1 3 года назад

That garage tho... Great content fellers.

@ronaldwilliams4053 Год назад

.30 over I love it already

@brandonfisher4071 4 месяца назад

Thanks y’all I was able to learn a lot from this video

@duudiefilms9895 Год назад

Getting ready to build one myself I never built one before

@monopython8487 Год назад

Finally getting ready to pull my 5.7 350 TBI from my 93 silverado . Want to make her a daily and upgraded performance too

@richardrichard4394 Год назад

Great vid covers a lot that reality tv does not have. your Son involved that's Bonus wish mine would be Addicted to HP sauce SBC

@jacobramos163 3 года назад

Great camera work I love how he gets every detail! To me that’s like half of the video is letting us see exactly what he’s doing

@MinnesotaisRust 2 года назад

Looking forward to watching this series.

@whipsmostwanted 3 года назад

Great video! Building my own engine is a goal of mine so I’m headed over to video 2. Lol 💪🏾💪🏾💪🏾

@ZHPGarage 3 года назад

Lol good stuff. Number 3 will be coming very soon also.

@timmeeks7318 2 года назад

Thank you

@kevincoyle9517 2 года назад

Great job! Much appreciated. This will be my first time. You gave me some confidence!

@Retro2502 2 года назад

Great video currently building one with my good friend and this has helped me out a lot!

@johnmilner7603 2 года назад

A 3/8” rubber fuel line on each rod bolt does wonders for safety when tapping the piston down.

@timothygeiger8271 2 года назад

That's what i was going to say. I liked to put the rubber fuel line on the bolts to keep from damaging the crankshaft. You should soak the pistons in motor oil before you install them as well.

@v8cars488 2 года назад

I am from Suisse super video Thanks.

@raymondruz9634 Год назад

Great knowledge transfer. Thanks.!

@dalescommonsense7676 3 месяца назад

Very helpful! Thank you so much

@anthonygallegos5198 3 месяца назад

This video will help me as well to rebuild my own 350 engine with my rebuild kit thanks keep the videos coming also wanna know how to wire I have a 1977 c10 so if you got videos on that as well definitely will check it out 👍🏽

@beaterstang0898 Год назад

Great video guys, very well laid out.

@SupersusSS606 9 дней назад

Getting an 81 z28 this weekend, currently runs and drives but wish me luck, I have a habit of turning cars into not that😂

@EnglishCharlie 2 года назад

Nice video, doing something similar with my 350 GMC.

@baldo5097 2 года назад

Awesome video guys

@steveblottenberger1097 Год назад

Very tight machine fit with main bearing caps you should take a bronze small little hammer and tap the Caps down then take the bolts and drawing down

@NbaEleven Год назад

Nicee. I want to build my 421 I think I can do it now lol

@eduardoperez7797 11 месяцев назад

Best video out there thanks guys.

@billyrector3578 2 года назад

ILove the video Good work Guys thanks

@steelavocado1 Год назад

I didn’t check my bearings when building a 327 over the summer. And I reused cam bearings. Engine sounds great but has no oil pressure lol. Gonna sell it and build a 350 the right way this time.

@jaysouza8177 8 месяцев назад

Do you show the cam bearings being put in? I don’t recall seeing that. You answered all of my questions except that one. Great content. Thank you.

@jesseduerksen6248 Год назад

Nicely done!!

@gabehebert6012 2 года назад

I have the same motor it makes 300 up naturally aspirated with a cam after market pistons and jegs heads

@GeorgiaRidgerunner 9 месяцев назад

staggering the seal helps prevents leaks its just good practice to not have all the seams lined up

@jeffadamson5522 2 года назад

You guys off set that rear seal it will never leak. No need for the RTV or silicone on the rear main caps....

@Beartracks777 3 года назад

Great stuff Man

@davidwilliams5551 3 года назад

We're waiting for part 2🧐

@ZHPGarage 3 года назад

We are too! Haha waiting on parts for it.

@jjmccloud 3 года назад

Its out

@peep2211XD 2 года назад

Badass build 🔥🤙🏾

@kosworkshop 3 года назад

Is there a part 3 for the 350 sbc build? My life feels incomplete as of now. I’m awaiting part 3 please. 😂

@ZHPGarage 3 года назад

A lot of other things got pushed in front of it, not sure when part 3 will be haha

@kosworkshop 3 года назад

@@ZHPGarage I have learned a lot from your videos and I appreciate it sir. I’ll stay tuned!

@dannygeouge8459 3 года назад

Super video!!

@ryanzimmerman1240 Год назад

So when checking the clearance for the bearings, if you have a reading that's not desired, you would get different size bearings to fix it?

@catboi1188 7 месяцев назад

Yep 😅

@Strider1526 2 года назад

Can the pistons be installed reverse if they aren't flat top? Great video!

@nwmod39 Год назад

Negative

@joelnelson941 Год назад

With regard to ring gap, you said "15 thou" but your on screen measurent is ".0015" or 1 and 1/2 thousandths.

@joelnelson941 Год назад

At 18:36 time stamp

@steveblottenberger1097 Год назад

You should stamp each cap as you take them off you can make your own stamper nomadic order

@makarnovikov9128 Год назад

Unless you are in -40 c you should not be using 0w20 5:30 in colder climates and 10:30+ in California climate or any hot weather

@joem4971 7 месяцев назад

i’m buying 350 with no headers and transmission for 50$ this video will be come very handy

@milesbocchi8917 3 года назад

Once the mains are torqued you need to spin it over once or twice tops and then take the caps off qnd read. Circle pattern also never heard of. Start in the middle and work your way out. Doing it in three steps. I haven't seen your method

@ZHPGarage 3 года назад

Well, first time for everything

@steveblottenberger1097 Год назад

You're pushing your luck not dinging that crankshaft journal you should put rubber hose on the rod bolts or summit racing has the ride bolt protectors as you put in the piston and otherwise you're doing a good job

@joeclark9042 2 года назад

Hey brother I just seen your video sorry it's a little late but hey where do I get those cleaners cuz I like to clean all the holes in my block I just got a new '01 block also it's a four-bolt main and I want to get it all cleaned up all the threads are my all that stuff so if you can give me a little hint where I can get the all those cleaners at I appreciate it brother Good looking motor

@ZHPGarage 2 года назад

The ones I have are from Snap On but other companies have them.

@m8_fanatic 9 месяцев назад

Awesome content, i have a 2 bolt 350 in my 66 impala im looking to get some power out of. So far ive done, edelbrock performer intake, new exhaust, new 600 holley, new distributor, lunati voodoo 262/268 cam. Where to from here? It goes well but i always want more!

@natejacobs1107 2 месяца назад

I know I’m late to the show but I’m going to start a build soon and I never have before. What other tools do I need except for basic tools

@israelitto 2 года назад

how do you know what oil to use once i’m done building my 350? i’m not sure what size bore i want to go with yet.

@kyleperry1701 Год назад

It doesn’t go by bore size it goes by tolerances on plastigauges Redon typically on crank bearing and rod bearing

@augustusappling139 Год назад

Subscribed thanks for the video man. what was the measurement at 9:30?

@SilentOneCorajuda13 3 года назад

I would of torqued the caps down in increments. Also, I would of never touched the inside of the main and rod bearings. 🤷‍♂️

@benscoggins3149 2 года назад

thats how i was taught

@connellfarm315 2 года назад

I was taught that as well but never could explain why. Also was told to never touch or rub the sleeves with your finger. Again I was never explained why but I assume it was bc small metal shavings..

@mcqueezi3388 2 года назад

@@connellfarm315 I’d assume the oil on your hands messes with motor oil

@marcelkevon7863 2 года назад

Why you ain’t use no lubricant?

@drewglines 2 года назад

Great video

@jjmccloud 2 года назад

Did you have the rotating assembly balanced or no? Still debating spending the money after changing pistons to flattops from dish. I know its preferred and a must for high rev high rpm builds but for a mild street build im debating skipping it this time around 🤔

@ZHPGarage 2 года назад

No, the owner of this engine didn’t get it balanced. If you are planning on the engine running higher RPM’s it’s a good idea to get it balanced.

@lordsauto Год назад

Hi Guys have a question. When i check end play do i do it with the rods out of block? And do i just snug the main caps down when smack with hammer?

@waynew2831 Год назад

Isn't there a certain torque sequence you are suppose to follow?

@codythomas9250 2 года назад

Can you list off all the parts for this build ?

@dottedvitalgecko6941 2 года назад

Idk if anyone will see this but what do I do if my pistons don't have dot indicators? They only have valve dents on one side

@dennyfrontier 2 года назад

At the beginning of the video around 8:50 when you were getting the clearance for the crankshaft... What was leaving those marks on the crankshaft and the bearing caps? Was it being scratched? I thought scratches were harmful to those pieces. When you used the paper to find the measurement, what were you doing with that information? Because if its wrong you cant undo the scratches you made and try again?

@ZHPGarage 2 года назад

That is a plastic gauge, it’s not scratching the bearings.

@silverpanda7167 2 года назад

You sound alot like the wooded Beardsmen lol

@ironhorse127 2 года назад

What Howards Cam did you use? Part number?

@baldo5097 Год назад

Awsome video guys would this engine work on 84 oldsmobile cutlass Supreme

@waynew2831 Год назад

I am re-ringing a 350 that has been bored 40 over. I ordered rings for a 40 over block. The bores measure 4.0415. The rings came in, and already they have a .025 to .027 end gap. Is this acceptable? This is naturally aspirated for street only.

@ryanjones7681 2 года назад

Can you just not measure everything and simply run a thinner oil? (Like Ford does)

@ZHPGarage 2 года назад

I guess you could, I personally wouldn’t.

@Dragons18 Год назад

Theres a reason why we are rebuilding a GM motor and not a Ford one

@sschevmale24 11 месяцев назад

😂

@shawnp001 Год назад

so i just started watching the video and I have never rebuilt an engine before so please excuse my ignorance , how did you determine the bearings for the crank and pistons, I have watched a few videos on this subject and I dont understand how to find the size if you are starting from scratch

@sabertooth1970 8 месяцев назад

14 minutes in I’m thinking use all new cap bolts

@lordsauto Год назад

Is it 65 ft lbs or 70? I have 2 bolt

@bricedentel4102 Год назад

Did u assembly lube the bottom of the 1st cylinder piston rod bearing? It cut out and I didnt see so just a question

@jtp682 Год назад

love your video its geat! I am hoping to get your opinion on something. I have a chevy 350 that I want to freshen up without machining. I specifically want to replace the main and rod bearings to increase engine longevity. So regarding the rod bearings, can I just replace them, do the clearance checks, and retorque them without having to change the rod bolts/nuts? Its just a stock, average HP late 70' engine that is just a daily driver. Thoughts on this?

@abitoferthang3788 5 месяцев назад

Same process for 283 sbc?

@cartracer64 Год назад

cam specs? thanks for the video

@jakestephens3689 3 года назад

what year was this block made?

@ZHPGarage 3 года назад

We looked a while ago, can't 100% remember but we think it was an 80's block.

@ralphnolan3187 2 года назад

Clevite bearings

@jjmccloud 3 года назад

No part 2?

@ZHPGarage 3 года назад

Coming very soon

@pumasisneros1 3 года назад

Part 2 is out there

@jjmccloud 3 года назад

@@pumasisneros1 👍🏻

@outdoorgarage3290 3 года назад

Where is part twoooo

@ZHPGarage 3 года назад

It’s up on our channel

@brandonbell8159 3 года назад

Is that the original engine from that c10?

@ZHPGarage 3 года назад

It is

@Jordanrhart Год назад

After you check the first rod cap with the plastigauge, do you pull it back back out so you can get assembly lube on the bearing before moving on to the next one @zhpgarage?

@steveblottenberger1097 Год назад

I agree with you cleaning the cylinder head threads but I disagree with you you should use attack and clean the threads up is not going to make it weaker there's no way and you want accurate torque sequence cast-iron is not very friendly with being exactly understand what I'm saying

@steveblottenberger1097 Год назад

Excuse me I meant to say you should use a tap to rethread the cylinder head threads it's not going to make the block weaker never heard of that

@billmeyer3728 2 года назад

I just love the SBC-yours looks great! Check out my SBC on my channel with a few surprises!

@coleparker436 Год назад

Am I the only one having issues with the volume?

@kelsiedennis1899 3 года назад

Who in the hell torques the crank down like that. I cringed during this whole video

@ZHPGarage 3 года назад

Thanks for watching

@jjmccloud 2 года назад

@@ZHPGarage 😆

@steveblottenberger1097 Год назад

Excuse me NUMACATIC ORDER YOU CAN STAMP THE CAPS YOURSELF YOU CAN MAKE UP A STAMPER WITH A CHISEL

@steveblottenberger1097 Год назад

I have always retapped the threads on cylinder blocks for the cylinder heads never had any trouble you're talkin about it being weak if you retype the threads 30 years I've never heard that one never seen any trouble because of that need to go do your homework again

@mo7.7 2 года назад

Dislike for not letting us hear the torque wrench clicks😩

@ZHPGarage 2 года назад

Hahaha

@jcp4264 Год назад

😅

@kickstation6923 3 года назад

The prickly route cumulatively delay because cry implicitly fix into a swift weight. lewd, assorted wood

@ZHPGarage 3 года назад

My thoughts exactly

@yolandashikers4985 3 года назад

The combative port historically interrupt because badge connolly place regarding a known organ. shrill, bright vinyl

@zafar78600 7 месяцев назад

poor audio

@jimbeam992 3 года назад

I knew American products were absolute garbage, but the way ya gingerly handle these American steel parts only leads me to believe that this motor will die under 100,000 miles in the typical Big 3 fashion.

@ZHPGarage 3 года назад

I’m not sure how American products being absolute garbage came up in this video in any sort of way, but these older engines weren’t engineered to go over 100,000 miles, hence why so many older cars got parked after only 5 or so years of driving on the original engine.

@jimbeam992 3 года назад

@@ZHPGarage True that. My 1999 Accord is 325K miles and running strong as ever, pretty sure it will out live me.