Buying a Junk-Yard Yamaha Blaster In Pieces. Will It Run?

Подписаться 468 тыс.

Просмотров 54 тыс.

0% 0

I buy a cheap junkyard Yamaha Blaster quad and try to get it pieced back together and running. #Blaster, #Yamaha, #2stroke,
►SUBSCRIBE: / @2vintage
►MY SECOND CHANNEL: • New Polaris ATV Snow P...
►FORUM: 2vintagerider.c...
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
►►► ADD ME ON ALL SOCIAL MEDIA ◄◄◄
► FACEBOOK: / 2vintageyoutube
► INSTAGRAM: 2_vintage_ / 2_vintage_
► SNAPCHAT the2vintage
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
► EMAIL FOR BUSINESS INQUIRIES ONLY: 2vintagetooo@gmail.com
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
Thanks for watching and subscribing!
New videos every week!
The following video features activities performed in controlled environments by knowledgeable persons. DO NOT attempt to duplicate, re-create, or perform the same or similar activities at home, as personal injury or property damage may result. 2vintage( Joe Weber, the persons shown in this video and ANY CONTRIBUTOR, ARE NOT LIABLE FOR ANY such injury or damage. ALL 2vintage( Joe Weber) CONTENT IS FOR ENTERTAINMENT PURPOSES ONLY.
2vintage (Joe Weber) makes no representation about the sufficiency of any safety precautions and equipment used in this video.

Опубликовано:

22 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 187

@2vintage 3 года назад

Who thinks this quad will run? Please SUBSCRIBE and LIKE the video if you enjoyed! It really helps me out a lot! Check out my Instagram: 2_vintage_ Thank you for all the support!

@leonardschonfeldt1724 3 года назад

I think it will

@tjpaulus7663 3 года назад

You can make anything run

@MultiDude1995 3 года назад

It will you got the quad gods watching

@Matthewmiller28 3 года назад

It will run. These blasters are pretty good at getting running. Only thing is getting them jetted correctly can be a pita. Looks like u got a good score there for sure.

@jayzfordayz7676 3 года назад

Need any parts for it I got a parts blaster no plastics but everything else is there I bought 2 for 120 bucks rebuilt the other one

@jakedurham7963 3 года назад

That motor will not shift laying on its side and you have to kind of rock the transmission shaft back and forth while doing it.

@dtacol2080 3 года назад

Yh and it will be clonky with no oil init lol

@dtacol2080 3 года назад

He’s learning leave him to it

@stopibeastin7196 3 года назад

One of my first experiences on a quad was a blaster bad ass quad!!! It was a racing one it would snatch your hands off the steering when you floored it

@magee16749 3 года назад

3/16 in round ball bearing will work for clutch push rod ball bearing. I have been torn apart old axle bearings apart and used the ball bearing out of them.

@Urmom_2277 3 года назад

That’s were the arm goes there is a bolt broke off in there easy fix if you can get the broke bolt out

@cherylt8590 3 года назад

Sweet can't wait to hear it run,I have a 92 and have owned it since 96,it has its original color however and it still runs like a charm 👍😊...

@Stergos69 3 года назад

You need another big work bench, time to get off the floor LOL

@Noslo_559 3 года назад

Shift detention and spring are missing. It stripped out. Gonna continue to watch till you notice. Happy you are doing a blaster. One of my favorites to work on.

@lifeinaday89 3 года назад

2v timeee. Finally the blaster

@djmystery7235 3 года назад

I remember putting together a blaster just like this last year, it was a ton of fun and it had power too, enough power to wheels with my 215lb fatass.

@jaydingarcia899 3 года назад

thumb nail: yamaha blaster in pieces will it run? the blaster with no engine in it:👁👄👁

@fullmetaljacket7 3 года назад

Like that it will run... down the hill

@jaydingarcia899 3 года назад

@@fullmetaljacket7 FAXX😭😭

@dgamble35 3 года назад

Haven't watched it yet but this is a video that will display your box to bike skills. Like the sticker on an ikea box SOME ASSEMBLY REQUIRED

@sandmanbub 3 года назад

Tip; If using a chain without o rings, place the chain in a pan with clean grease and heat until the grease melts. Give it a few minutes to flow between the rollers and pins, then let it cool off. The grease will be in the chain for a long time.

@unchained20000000 3 года назад

I wish you would build a work bench. You are doing it on the floor like the videos in India restoration. They're good and so are you, but it would be more gooder using a work bench.

@Codyjames83 3 года назад

Right save your back your older self will be thank you

@Yamaha350w 3 года назад

Yea way”gooder” lol

@davidthorburn9327 3 года назад

user unknown 😂😂😂

@keatin1063 3 года назад

I have some spare blaster parts, o built a blaster up as a race bike and changed slot so I have a bunch of stock parts including stock suspension components and a whole mother frame, plus more, if you need anything

@johncordova2089 3 года назад

Looks like your missing your clutch boss spring in your clutch assembly it goes after your first friction and steel plates.

@mattgrimes1042 3 года назад

Didnt see the clutch push rod or ball for the clutch boss also would do a mixer delete and mix ur own gas <a href="#" class="seekto" data-time="1921">32:1</a> save u from blowing a piston and cracking the cases when the pump gose bad

@myguitaryourface5160 3 года назад

It's great when people complain cause your not using a work bench,it's your project and garage,so does it really matter?

@kernelbadness 3 года назад

It doesn't matter just suggestions. It's ultimately his decision but i think we can all agree a bench will help him and getting those parts off the dirty floor is a plus. His content will be better for it.

@soloskywalker 3 года назад

I always work on the garage floor. I like the space.

@jensenpetersen3832 3 года назад

Idk if you remember me but we found a banshee and it's really cool to see you rebuild the bike that I ride

@istvanszabo8537 3 года назад

love your videos. cant wait to see this running

@scottyboi2673 3 года назад

Always a good day when he posts

@davidthorburn9327 3 года назад

Yes!!!!!!!!!

@jonahharman2321 3 года назад

I get so excited when I see that you uploaded a video

@m8fusion712 3 года назад

I had one there fun quads to play around on, great video man

@davidinacio2704 3 года назад

You should buy another Yamaha Warrior 350 they are great quads

@tjpaulus7663 3 года назад

I just bought one and I love it

@yobro4423 3 года назад

@@tjpaulus7663 same here , just bought one 2 days ago . Love it , it's a 96 and it does need sum work , mainly electrical

@trevorcrane5271 3 года назад

Id love to se an old rough 70-80's kawasaki KE 125

@johnrankin9129 3 года назад

These videos are awesome. He explains everything so damn well.

@morrow49 3 года назад

Hell yeah! I got a 2000 blaster, excited for some more blaster content. I got a couple idling videos posted. Not trying to have anyone click my page, I just have a full pro circuit exhaust and Alba arms.

@bozobuiltit 3 года назад

I hav a 2005 from my bestfriend that got killed in a car accident its been garage kept like mint

@morrow49 3 года назад

@@bozobuiltit I’m sorry for your loss man

@bozobuiltit 3 года назад

@@morrow49 its ok thanks it was almost 15 years ago hes father gets all teared up every time he rides it

@jrchaidez2143 3 года назад

Excellent video, great RU-vidr that actually knows what he’s doing!!

@grantkozopas8738 2 года назад

Unbelievable .. "know's what he's doing???" have you seen how many machines they blow up?

@that_carguy3551 3 года назад

Damn I’m early. Love your vids man keep up the good work 🤙🏻

@MultiDude1995 3 года назад

I love your videos and i love it that you can upload this frequently... im addicted hahaha greetings from holland and please keep doing it the way you always do

@jayeddleston9486 3 года назад

Unbelievable you the man. Videos are awesome

@gamingboy-wk6dy 3 года назад

Love your videos

@MM_in_Havasu 3 года назад

That little arm you showed us earlier in the video is the shift drum stopper arm. It should be spring loaded against the star wheel.

@Hanky_Bannist8r 3 года назад

Awesome job Joe you saved another one !

@ChristianHelser999 3 года назад

Your missing that spring plate in the clutch basket.(whatever it's called) It won't work if it's not in. Dealt with same problem

@peteraitken6494 3 года назад

Hi joe what's the music at the start of the video thanks good job on the blaster so far 👍👌🔧🔧🔧

@siemverrijth3713 3 года назад

finally a blaster!

@alexportillo6050 3 года назад

This project is amazing good work keep up the great work I love your videos

@thomasholroyd5477 3 года назад

I would really like to see you get a Honda 300ex or a Suzuki ltr450 or a Yamaha yfz450

@user-xv2iz7ix5o 3 года назад

He just got a yfz it’s on his story

@VermontLife 3 года назад

Nice work, I got a kick out of seeing you stack the clutch with a diagram on your phone. I can't tell you how much time I spent doing the same thing after doing a tear down rebuild of an 89 Yamaha Moto 4 350 on my channel.

@briang4470 3 года назад

I know your trying to get the bike back together as cheap as possible but you really should have put a new set of crank seals in. I have personally had several 2 stroke bikes that were very hard to start or ran poorly due to leaking seals, they are cheap and easy to replace with the motor apart, to me it's just good cheap insurance of not having any issues once it's up and running. These blasters are pretty fun and easy to work on.

@wesleyoos71 3 года назад

Hell ya joe way to challenge yourself 👍

@prestonwinfrey7731 3 года назад

you and that tore glove, name a better duo

@johnnyjohnson2942 3 года назад

You can actually Anneal copper head gaskets and reuse them. Annealing is heating the gasket up to a glow and letting it naturally cool off.

@johnnyjohnson2942 3 года назад

Oh nice video!!

@Maga4Lyfe 3 года назад

Great Job!

@thetwostrokerebuilder 3 года назад

Check the shift fork pins roll on something flat ,look at the drum where forks ride for wear. Those will make it not shift. That arm will make no difference if anything be easier to shift without it. Also you weren't spinning the trans while trying to shift so could be your problem

@kernelbadness 3 года назад

Need new oem base and head gaskets! copper head gasket needs to be annealed if reused. Don't skimp here. Leak test.

@timmyinzerma7987 3 года назад

Been waiting for see this

@edcase7888 3 года назад

you might want to grease the swing arm bolt

@billysantiesteban4199 3 года назад

Smash an old bearing for the missing ball.

@highlightzilla9581 2 года назад

I wish I could get lucky to come across a blaster for cheap would be a blessingg

@sethnelson8698 3 года назад

🤦 U reused the old GASKETS!!?, WHYYY. I know from buying others people's junk not to reuse old gaskets. I bout a blaster from a guy for 600 bucks complete, he said it hadn't ran in a while but ran fine before and had a "fresh top end". So I do the usual, clean carb, fresh fuel, check spark. I go to fire it up, take like 15-20 kicks and when it does it sucking air from every direction( massive air leak). I pull the stator cover, 1: half the threads on the crank are gone, 2: the middle half of the crank seal was gone, and 3: was missing a stator bolt. Then, I pull the head and cylinder off, and guess what, old piston, honed bore, and a new base gasket stacked on top of half of an old one. Take the clutch cover off, and the counter balancer gear was off time. That's just my personal experience man, so I highly advise u to redo what u just did with new parts, instead of selling it once u get it running to "your standards", which from what I've seen in the past, ain't normally good.

@tonymassingill6032 3 года назад

Somebody's project that did not get done before it got traded to you is a lot different than junk out of a junkyard.

@djmystery7235 3 года назад

Also, if you want the engine to shift you have to turn the input shaft, but with how loose that drum was I’m gonna guess the transmission was messed up.

@jackbeanstock7710 3 года назад

DUDE why did you skip showing the drill and tap process ? doing a repair video, and then skipping the repair steps, seems kinda odd to me?

@2vintage 3 года назад

Next time I'll keep it in. I thought it was a boring part so I kept it out.

@soloskywalker 3 года назад

@@2vintage I would like to see how to tap as well. Great video otherwise.

@763GanderGuys 3 года назад

Time for a work bench in 30 years you will thank your self.

@-jeffreybollenbach- 3 года назад

I think I saw some purple under those black plastics. I think you should try to get that purple back its rare

@fuhkoffandie 3 года назад

man why can't I find deals like this. yeah Bent shift forks are not all that uncommon. it's such a simple motor, the cases can be split and the engine rebuilt in an afternoon or evening. the main thing to watch out for, make sure you're piston doesn't have speckly little dents and things in it. the top of the Piston should not look like coarse sandpaper. this is a sign that the crank bearing has gone bad. that's by far the worst thing on this whole bike to go bad, is the crank bearing, or, actually, it's the connecting rod lower bearing. it's the worst thing that happens with a two-stroke aside from a extremely scored piston. other than that, everything is very easy and straightforward on this motor and that's why this bike is so awesome. two strokes rule, four strokes drool.🥴💢🏁😜💯💯💯💯

@bobbyisno11 3 года назад

It's a Gypsy moth larvae and they will give you a rash and can also give you respiratory problems.

@nickgruber2593 3 года назад

Great video as always! Can’t wait to see the next one 👍

@MOTO_MAVERICK53 3 года назад

If you reuse copper gaskets your supposed to heat them up with a torch first because it softens the copper

@cliff_wolfe414 3 года назад

Dats gonna be alot of work dude

@javieravila8046 3 года назад

You should get Honda 300 four trax

@joeleeman9886 2 года назад

So I just clicked on one of the later videos in the series and after watching the first 10 seconds of this one are you telling me all this thing needed was a chain, air filter and petcock? Holy shit

@joeleeman9886 2 года назад

ok after finishing the vid I see you needed like 3 additional very inexpensive parts, this was a great find. Are you self taught mechanic, i just get that feeling by how you flow through each item.

@Gcornelius06 3 года назад

Can’t wait for tomorrow’s video 😁😁

@rvnmorphs214 3 года назад

I was looking if you posted a new vid and when i opend youtube i saw it posted 4 minutes ago

@CLPOZ 3 года назад

I wish I can just drop my dirt bike off for you to fix 😂 great videos I subbed

@sulmyhernandez8503 3 года назад

I think it would be great do to a race between a 400ex and blaster 200.

@motorcycleandtoolrehab1834 3 года назад

I'm just about to do a similar video on my YT Channel. I bought a basket case KX250f that came in boxes. I usually stay away from such builds but I have a heap of spare parts from previous projects that should get it running. You should invest in some machine shop tools and learn to use them as If your doing this fulltime you will save a lot of money. Look at getting a lathe, milling machine and surface grinder. I use mine daily working on projects and have saved thousands making your own parts. Anyway just a suggestion and good luck with the build. If you need any help please ask. Cheers Rick MTR

@mikestowe6136 3 года назад

great video wish i had half your patience lol

@dylanphillips9745 3 года назад

If your looking to sell ill buy it👍

@joneserupinsmoke9161 2 года назад

Two stroke is where it's at

@lucindarose5580 3 года назад

No way I’m just doing same thing just got the hole frame now engine carb source in few parts atm

@ni_wink84 3 года назад

Somone had a vid clip of your brother on the CR500 on tiktok user name was turkeybirdd, I was like hey!! I’ve seen that video lol

@sampson1234567891011 2 года назад

what a hack of a "mechanic" if you even wanna call it that. Guy is reusing base gaskets and even reusing a head gasket , which is a one time "crush" use. reusing old clutch plates and fibers. Also reusing a used piston and rings and didn't even get the cylinder bored or honed. split the cases because of a "shifting" issue and never even had it assembled enough to test it to be able to shift. Those 5 bolts for the clutch pressure plate you ran up and hit with the impact are 8 ft/IBS. Did you even use the correct washers behind the clutch basket? Did you check the side to side freeplay on the crankshaft? Did you check the rotational play on the clutch basket? Did you lap the cases to make sure they were flat? Did you replace the two crush washers ? Did you adjust the clutch properly? I doubt it. This is a great video on how NOT to build your blaster motor, good job.

@Aint9sk8rd9 3 года назад

Good stuff 👍 you should try to find a fuel injected yz450f

@connersnow298 3 года назад

Awesome vid and edits and filming and bikes

@N3LP 3 года назад

Great video thanks for uploading today 😊

@ridemachines9741 Год назад

Whats up buddy i just wanna say congrats on your channel growing but man im on the rocks do you have a spear exhaust for blaster the one i have snapped in halfs

@kevins6698 2 года назад

Im Having problema with my Blaster im Running 280 main jet no lid filter Dg silencer when i start running feels like bogging then run strong at high iddle i already clean the carb any suggestions??

@averagecarguy420 3 года назад

Time for a banshee

@84CutDawg 3 года назад

I’m trying to find another Blaster I have a 350 Rancher rn

@carltreurnich8482 3 года назад

I knew it was that shift spring

@mattsfishingadventures363 3 года назад

<a href="#" class="seekto" data-time="598">9:58</a> Yum! 😂

@RafaelGamer43210 3 года назад

excelent doctor!!!!

@RAYtheram 3 года назад

I really do like watching your content, I had to do a timing chain on my rmz450 and I was afraid of doing it and messing it up but after watching you for the last year or so I did it and it was no where near as bad as I thought it would have been plus I saved nearly $400aud

@gamingboy-wk6dy 3 года назад

Can u please do a 200cc quad bike please i need to see how to open a engine

@Guadzilla459 3 года назад

Look it up on RU-vid what ever engine you trying to split

@tyler238 3 года назад

Oh god, those are always beat

@jafar4502 3 года назад

Just got me a Kawasaki Mojave 250 I really like it but seems like it’s holding back power any tips

@marshallnaville1079 3 года назад

Air restrictions possibly? Exhaust could have something in it.

@elliotjones9097 3 года назад

Could you show me how to replace the piston on a 2 stroke?

@JesusLov11 3 года назад

What kind of electric drill to you use i see you using it all the time and it seems like its got some power.

@stevenmillar8810 3 года назад

for a while i have asked for a new stock bike yz is my fave then supe it up new light weight wheels new pipe front to back titaniam bolts everyware make a race bike

@joneserupinsmoke9161 2 года назад

Hell yea joe get it bro👍👍

@YoungBoul_ 3 года назад

My guess is that he traded the atc 250 for that and something else👀

@wallpaperman9051 3 года назад

I think he traded it for a CB350. There was a story on Instagram with one in the back of his truck.

@leonardschonfeldt1724 3 года назад

Love your Vids

@devindunlap0494 3 года назад

I just traded one of those for a 400 ex with a really bad valve rattle I'm just gonna rebuild it I think

@johntrout7572 3 года назад

Awesome video

@kikemotors6138 3 года назад

I just bought two blasters one has bottom end broken hole thru case other is in pices but I have like 4 sets of heads and jugs.do you think if I reuse they should be good mine like pretty much like urs not damaged beat up no scoring no scratches ? For the piston jug and head is what I'm asking about