CBR300R,CB300F Oil & Filter Change with Fairing Removal

Подписаться 427

Просмотров 37 тыс.

50% 1

This video is about the Honda CBR 300 oil and filter change. The same process can be used for the CB300 which doesn't have fairings. We found out the fairings do not have to be removed to access the oil filter. They only have to be loosened enough to access a bolt behind the middle fairing. This will let you remove the lower cowling/fairing to get at the oil filter cap. This is a long video and is meant as a guide to help you through the oil change process. There may be other solutions or methods but this is what we went with. Some may not approve of my methods (re-using the oil washer and gasket or the type of oil) but I confident there is enough information to help most people get through the job.
Note on audio - the audio is a voiceover because the original audio was muffled and unusable.
Tools Needed (in addition to the manual)
Socket set (12mm and 8 mm sockets), Allen Keys, Rags, Oil Pan, Flashlight, Manual, Engine Oil, Filter and Gasket, Rubber Gloves, Phillips and Flat Screwdriver, funnel, torque wrench, Oil bolt seal, Bike Stand and some newspapers to place under the bike while draining.
Required Oil (when changing the oil & filter) - 1.5 liters (1.6 U.S. qt)
When changing the oil only - 1.4 liters (1.5 U.S. qt)
Oil - 10W 30 (I used 10W 40 which will work too without issue)
Oil Filter - Honda Part # 15410-KY-901 (I used K&N Part number KN-112)
Oil Filter Gasket - Honda Part #15412-KY-901
Oil Bolt (Crush) Washer (12mm) - 94109-12000
Technical Info:
Torque settings for the Oil Filter - 9lb-ft (12-m, 1.2 kgf-m)
Oil Drain Bolt - 18 lbf-ft (24 N-m, 2.4 kgf-m)
Notes and Corrections: In this video we hand tightened the bolts and checked them again with a torque wrench off camera - We recommend you invest in a torque wrench. Remember tighter isn’t better but the instructions in the video will get you by.
The filter spring - the filter spring was put back in off camera.
Visit us at www.cooldadreviews.com

Авто/Мото

Опубликовано:

20 июл 2016

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 60

@maiaf2742 2 месяца назад

I’ve never done maintenance on anything in my life, this was so helpful thank you

@fatboyz4-lyfe992 7 лет назад

great job but you forgot to put the spring back in with the filter,

@michaelbriggs6306 4 года назад

I forgot to add my spring too! what should I do! I feel like all the oil will spill out if i take the filter out again

@rsanchez5676 11 месяцев назад

It only leaks a few drips. Nothing to speak of really.

@motoryzen 6 лет назад

This is by FAAAAR the best video of oil change of cbr300r. Everyone else's misses one thing or many things including the damn tools needed ( facepalm).

@KevinPughCM 6 лет назад

tpcs this one missed putting the spring back in with the filter. Doh!

@punchingdoll 3 года назад

Ouch the filter pressure spring!

@noforktouse 4 года назад

Very nice and helpful video! I'm going to try changing my oil soon as my 300 is getting close to 3k miles. I hope it goes smoothly and will be rewatching this video as I do it.

@asadrinna 2 года назад

I noticed that the oil filter spring wasn’t put back after the oil change

@atotalmoron 5 лет назад

Thank you for showing which screws go where. We just did an R6 shock swap and in the process mixed up the shouldered screws... Ours were missing the rubber washer on a couple, which explains everything.

@LunchBXcrue 4 года назад

Awesome thanks! With this guide I was able to take the right side off so I could run the cable for my gear indicator. Thanks.

@Sabadiver 3 года назад

First class presentation

@imadafat 6 лет назад

Great video thanks

@mikeortiz410 3 года назад

Yoo, just looked this up on google to see how to change my oil and you have the same bike, right down to the color. Thanks for the help!

@AlcatrazMeow 6 лет назад

Will putting 15w50 motul 300v is good? I live in a country where its hot most year around, usually 35c degress and up. what does the owner manual says?

@chicomendez5324 11 месяцев назад

Thank you so much , that’s a great tutorial , I learned a lot . Now I’m trying to replaced the kickstand switch and I don’t know where to start . A video on that will be greatly appreciated. In advance a big THANK YOU ! Subscribed!😀

@valmirberisha5663 3 года назад

Oil is dripping from the filter area but I've tied the screws as recommended by manual. Is it normal that it's dripping the first couple of times I've turn on the bike?

@Lilbizkit 5 лет назад

Did you tilt the bike so that it was bolt upright when checking the oil level (as opposed to checking while the bike is on the side stand)?

@NamesRjayz 5 лет назад

Does the oil from the glass window disappear when you start the bike? Because I’m scared I didn’t put enough in

@thespeeddemon5685 3 года назад

After I put the oil and turned on the bike how long until the oil settles down after I turned the bike off. So I can see how much to add after the oil is in the filter.

@cjerryc7232 7 лет назад

Good! I tried four times to remove all the fairing, but never successedl！ Hope you can do it and upload the entire operation process! Thank You Very Much!

@martinamicflyy2618 7 лет назад

thanks

@josejimenez3578 5 лет назад

How often should I do a oil change ?

@rsanchez5676 11 месяцев назад

Was wondering when you put the oil filter spring back in. Others noticed as well.

@NAJErEa91 2 года назад

@14:14 😑that is the bolt that is rounded out on my bike. I've already successfully changed the oil but now I'm trying to change the oil filter on my 2017 Honda Cbr300r but cannot due to this bolt being so severely rounded out. Do you have any advice on how to extract it???

@valmirberisha5232 3 года назад

Manual says to use SAE 10W-30, can you tell me why you used SAE 10W-40? What is the difference?

@brucejheison 8 лет назад

thank you for this video, if it wasn't for that i wouldn't have been able to do my oil change...much appreciated!!!! one last question though, when the bike is turned off the oil level is good, but when i turn the bike on, the oil almost disappears from that little gauge window. when I turn it off the oil goes to the normal level....is that normal?

@cooldadreviews8580 8 лет назад

Hi Bruce. Sometimes you have to level the bike to see a true oil reading. As long as you filled 1.4 to 1.5 liters you're good to go. When the bike is on - the system is using the oil so the level won't show properly. When the bike is off the oil is resting. This is when you want to check the level. As long as it is at the right level and the oil is clean all is good. I hope this helps.

@Cruz474 6 лет назад

I could for the love of god not get one of the screws out, the one near the header. However I managed to get all the other ones out, and it was enough to peel back the fairing so that I could access the oil filter. Have to be careful not the crack it.

@jonathonb2859 7 лет назад

What Allan kit do you have??? I'm not very familiar with tools. I'm learning.

@cooldadreviews8580 7 лет назад

Hi Jonathan 4,5 and 6 metric hex/Allen key. They come in most sets. I have a set that came with my socket set. If you don't have any it's a good investment. They under $20. Make sure they're metric. Amazon has them too. These will do. I pasted a link below. The kind that attach to a screwdriver is good too. Good luck. www.amazon.ca/dp/B00I5TH074/ref=pd_lpo_sbs_dp_ss_1?pf_rd_p=1977604522&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=B0025ZA3EQ&pf_rd_m=A3DWYIK6Y9EEQB&pf_rd_r=3R4SFP3GPCC4P1E02W7X

@alexandreberube7351 8 лет назад

Hi, I bought the cbr300 about two months ago. i am currently at 1100km and it was recommended to change the oil at 1000 (which I will do as soon as possible) I now use my car in fear of overusing my bike. do I need to change the filter for the first oil change, or can I only change the oil? thank you

@cooldadreviews8580 8 лет назад

Hi Alexandre. Don't worry about not riding your bike. It will be fine. The service manual recommends the oil and filter be changed the first time around. You'll want to change the filter because bits of metal and debris will be caught in the filter. This is normal and part of the break-in period. I recommend you change both the oil and the filter. You can order all the parts you need online. I have a list of the OEM parts in the description to help you out. Good luck!

@devmurasing3869 4 года назад

Wow Nice Honda Cbr 250R My Bike

@yazzehunter6556 8 лет назад

Any tips on taking out the windshield?

@deseq546 8 лет назад

You got to press this little hook at the tip, was a bitch to take out. took me awhile LOL

@patricktrouve1 6 лет назад

Going to do my first oil change this weekend. I've had the bike for a little over a year (the dealer did the first pre-winter oil change). Im selling the bike in the spring for a new, bigger bike. Is it worth it to go through the pain in the ass of removing fairings/changing filter, or is changing the oil sufficient. Granted, I'm going to garage it soon (i'm in new hampshire) and will sell it early spring

@cooldadreviews8580 6 лет назад

Hi Patrick. If haven't written much just change the oil.

@NAJErEa91 2 года назад

🙌 THANK U FOR ASKING THIS QUESTION!

@brucejheison 8 лет назад

could I use this tutorial for the 2016 model ?

@cooldadreviews8580 8 лет назад

Hi Bruce. Yes you can. The only difference I saw between model years is the color. The oil and filter change is the same. The fairing removal is the hard part and they come off the same way. Good luck.

@infernowolf36 6 лет назад

Thank you. That was very Time consuming vs my car

@OJMAH 3 года назад

it seemed like he poured too much oil into his bike. 1.5l with oil filter change. but as you added to oil filter. you might need another 1.4l the same amount changing oil without changing oil filter required. and even in Thailand 10w30 is used as original factory maintenance program after sale.

@mikedossino3804 8 лет назад

I was able to access the bolt without doing anything... BUT I scuffed up the fairing and was so pissed off. I see why you need to remove it now. I left the bolt off cause I don't need that shit. Honda get with it!

@tomzauto 4 года назад

We'll check it later with a torque wrench? Why not just use it now...? Also you might want to take the filter back off and install the filter spring, without out it most of the oil will bypass the filter, plus once a crush washer is crushed it's done, just get a new one they are cheap. But other than that nice step by step tutorial.

@4N2IN0JA 5 лет назад

Very detailed video! I think I’m going to use a hole saw and drill holes Then line the edges with some rubber trim. That’s a lot of work to get to the oil filter and drain plug.

@myildirim 7 лет назад

I just could not take the drain bolt off, and broke my socket wrench while trying. Then tried to tighten it a bit more but, not sure if i could do enough or not.... :( So for those who really wants to take that drain bolt off, get a big long socket wrench.....

@nikaigoria4242 4 месяца назад

am i tripping or did he forget to put the spring back on

@rodrixmmx 5 лет назад

Todo bien hasta que olvidó el resorte del filtro...

@zainjaved121 2 года назад

which is best aftermarket exhaust for cbr 300?

@Stuka303 7 лет назад

What's the cost to have a dealer do it

@cooldadreviews8580 7 лет назад

Hi True Stuka. (I like the handle) It depends on where you take the bike. The dealer will always be a little more. Oil and Filter change may run you $100+. I know someone who paid $140. They'll do a chain clean and lube up all the moving parts. A straight oil change is easy to do and fun to do. No fairing removal. You don't really need to take the fairing off if you want to change the filter...just pull back the lower fairing to get at the bolts. I took it off because I don't want to risk cracking it. That's me. If you have tools the cost of an oil change is your time and $15 in oil.

@Stuka303 7 лет назад

Cool Dad Reviews thank you

@jimfrick826 5 лет назад

This is such a great little bike but HONDA really blew it by covering up the oil filter cover. This should have been easy.

@NAJErEa91 2 года назад

Totally agree! I changed my engine oil but cannot get to mt filter 😑i might have to get that part professionally done

@yeugeniuss 5 лет назад

Would be nice to have a video about actual middle cowl removing and putting it back. In case you need to flush coolant, install crash pads etc.

@elchaconaso 7 лет назад

ill give you a like but you can change oil filter w/o removing fairing.

@cooldadreviews8580 7 лет назад

Thanks for the like. You're right you don't need to take off all the fairings. But some people who are new to motorcycles are afraid to break or crack the fairings so this video shows you how to take them off. Once you have that hidden bolt off you can actually pull back a lower Fairing and take off the oil filter.