*Coming up on having had this saw for a year....am a casual user and bought it to cut up sections for bowl blanks. Easy to start, **Bestfor.Garden** also recommend even after storage for a couple of months. Simple chain tension adjustment. Just cut up some 20" Osage Orange, including ripping bolts in half (at an angle). Like butter!*
The same chainsaw as my old Einhell chainsaw. I only had to adjust the carburetor correctly because the device started well but didn't take any gas. All the components are absolutely the same. I think it's a very reliable saw when it's not dying. I once had it in the garage for a little over two years and the gasoline smelled like kerosene. I filled it with fresh gasoline, pulled it twice and it ran as usual. I only had to change one fuel hose after 3 years because it had become a bit porous. My conclusion: a good device for little money...
It is the Chinese-made one that I own in Italy. She is honest. To get it started after a long pause, I pierced the air filter with a 1 mm hole and put in a little mixture with a syringe ... it starts immediately!
Thank you so much im from turkey sizin sayenizde ağaç motorumu hayata döndürdüm artık çalışıyor... Thanks to you, I cleaned the carburetor and now my tree engine is running....
Hola, para comenzar vacía deposito gasolina y ponle combustible/mezcla nuevo...antes de intentar arrancar tiene que estar bloqueado el gatillo del acelerador(tu no lo tienes bloqueado) , después cerrar entrada aire al carburador (estárter estirado), ya puedes tirar cuerda arranque si después de tres o cuatro intentos no sentiste explosión sigue probando con el estárter un poco a medio (si no corres riesgo de ahogamiento motor). Llegado a este punto y para descartar chispa, quita bujía ponle un poco de spray limpia carburadores o gasolina/ mezcla por el orificio y vuelve ha ponerle bujía y intenta arrancar...si arranca por un momento y se para el problema será de carburador, mangueras o filtro combustible A si lo hago yo. Saludos a todos.
La mía es nueva y se ahoga y no prende, ya limpie varias veces el carburador, una cosa que note es que el filtro de aire igual al del vídeo estaba roto
Nice i will try it tomorrow for my Chainsaw. I purchased new one but I'm very disappointed because it's never start up. I hope that's only the issues. I will clean the carburetor and sparkplug tomorrow.
It's all good but if saw has low compression, nothing will bring it back to life. I did all of these things he doing and saw did not turn on. It turned out that cylinder was bad. I think he should say why he jumped to conclude that Carb is bad.
@@SA-lr1sf Probably because he felt that the compression was good so the cylinder, rings and piston were still good. However I would have tipped the fuel (and any water as seen in the carby) out and replaced with known clean 2-stroke fuel. AND checked the tank strainer was clean and no holes in the fuel hose and diaphram drive pipe before pulling the carby to bits. Also cranked it over to see a good plug spark as well. Carby jets and strainers can get blocked and diaphrams puncture etc but much less often than muck in the fuel tank and perished hoses.
Wenn man das nachmacht, wird der Motor dauerhaft geschädigt! Es muss die Zündkerze eingeschraubt sein, wenn man mit Druckluft den Vergaserraum ausbläst. sonst kommt der dort befindliche Staub und sand an den Kolben und zerstört Zylinder und Kolben dauerhaft.
I do not have to remove the carburetor to clean, just remove the spark plug then pull and hold the starting rope a few times, put the spark plug back in and pull to restart- work well for me , chain saw, pressure washing machines all those 2 cycle engines.
Quedò mal armado el carburador,està acelerada y probablemente no le està entregando combustible adecuado al cilindro por culpa de la membrana que no logra empujar bien el punzòn. Te recomiendo levantar un poco la leva
chinese garbage of saw , i had it too just like this model only total red but everything else same and it makes you get crazy how quality build are terribly bad and what is more worse they only costs now 2x less then brand named ones as Solo,Husqwarna and similar
tieto píly robia v Číne , poznám ich ako abecedu a dlaň, u nás je to hlavne značka Hecht, červené krytie, no kopiruje to i iné značky, toto konkrétne vyzerá na 45 ku sú tvrdšie nemajú odpruženie ako značka Husqvarna a Stihl a sú ťažšie, lišta i reťaz sú z ,,blata, vätšinou 40 cm reťaz 1,5-3.25-66zubová , no za tú cenu pre niekoho kto nepíli často je to skvelá píla, ide max na 9 500 otáčok za minútu ,lebo pri vyšších otáčkách by sa rozletela, predali sme ich hromadu a nevracali sa do servisu... tak, že doporučujem
У меня такая же пила раз 5 пользовался потом перестала заводиться аж веревку порвал стояла года три отдали в мастерскую там подшаманили говорят завелась но сам когда начал заводить даже не чихнула ниразу пустил на запчасти
Vidim dobře že je v karburátoru voda? Při rozebírání je vidět nějaké kapičky u membránového přepouštění benzínu. Podle mého názoru tato pila stála delší dobu bez provozu a zkondenzovala voda v benzínu. Často pomůže jen vylít benzín a nalít čerstvý. Většinou pila naskočí po výměně snadno. Jinak je dobré si také vyzkoušet funkčnost svíčky zda hází jiskru. Nevím jaká má být v tomto typu karburátoru membrána, ale přijde mi to že je již malinko unavená. To také může mít vliv na chod motoru.
I always check for spark, first, then for gas. Squirting a little gas down it’s throat quickly checks for spark, because if it runs, you have spark. If it does not, then spark is the problem. Did you put the diaphragms on right? Metering side - gasket, first, diaphragm, second. Pump side. - diaphragm, first, gasket, second.
Vergaser Grundeinstellung, Motor Drehzahlbegrenzung, Leerlaufdüse und Leerlaufdrehzahl, nach Herstellerangaben einstellen, vor dem Einbau! Wenn das nicht geschieht, kann der Motor überdrehen und das Pleuel abreissen! Dann ist die Säge nur noch SCHROTT!
Сказки. В. Сухом. И. Новом. Карбе. Незаводится. (. У. Меня. 8. Лет. Пила. Работала. А потом. Незаводилась. ). Часто меняю. Свечи. И. ПОДКАЧКУ.. Заводится. Сразу. )
I did all of these things to my pro260 but it did not turn on. It turned out that it had low compression. You are lucky that it turned on. Please tell your viewers how you diagnosed the saw.
La mia è un vecchio modello che non ha la pompetta per la miscela. Non riesco a farla partire. Se la porto ad uno specialista spendo di più che comprarla nuova.