#Configure_Cisco_AP #Standalone_GUI #internet #router #ciscoswitch
Configure Cisco Access Point using GUI Standalone/Autonomous with WPAv2 Authentication Key
Configuring a Cisco Access Point involves multiple steps, and the exact commands and procedures can vary depending on the model and firmware version of the access point. However, here is a general outline of the steps involved in configuring a Cisco Access Point:
Connect to the access point: Connect your computer to the access point using an Ethernet cable or connect to the access point's default Wi-Fi network if available.
Access the command-line interface: Open a terminal emulator program, such as PuTTY, and establish a console connection to the access point. Use the appropriate serial connection settings (baud rate, data bits, parity, stop bits).
Enter privileged EXEC mode: After establishing a console connection, you'll need to enter privileged EXEC mode by entering the enable command and providing the enable password if configured.
Enter global configuration mode: Once in privileged EXEC mode, enter global configuration mode by typing the configure terminal command.
Configure basic settings:
Set the access point's hostname using the hostname command.
Configure an IP address on the access point's management interface using the interface command and specifying the IP address and subnet mask.
Set the default gateway using the ip default-gateway command.
Configure wireless settings:
Create a wireless LAN (WLAN) by configuring a service set identifier (SSID) using the dot11 ssid command.
Assign a security mechanism to the WLAN, such as WPA2 or WPA3, using the authentication key-management command and specifying the encryption type and passphrase.
Configure other parameters, such as channel and transmit power, using the interface dot11radio command.
Apply additional configurations:
Configure additional interfaces, such as Ethernet interfaces or VLAN interfaces, if required.
Set up any additional services or protocols, such as DHCP or SNMP, using the appropriate commands.
Save the configuration: Once you have finished configuring the access point, save the configuration to non-volatile memory using the write memory or copy running-config startup-config command.
Verify the configuration: Test the configuration by connecting to the access point's Wi-Fi network and verifying that it functions as expected.
It's important to note that this is a general outline, and the specific commands and procedures may differ depending on the access point model and firmware version. It's recommended to consult the Cisco documentation or seek assistance from Cisco support for detailed instructions specific to your access point model.
سیسکو ایکسیس پوائنٹ کونفیگر کرنے کے لئے متعدد اقدامات کا استعمال کیا جاتا ہے اور تفصیلی احکامات اور طریقے ماڈل اور فریم ورز ورژن پر منحصر ہوسکتے ہیں۔ یہاں ، میں آپ کو ایک عمومی تشریح پیش کر رہا ہوں جو سیسکو ایکسیس پوائنٹ کے تشریح کرنے کے قدموں کو شامل کرتی ہے:
ایکسیس پوائنٹ سے جڑنا: کمپیوٹر کو ایکسیس پوائنٹ سے ایتھرنیٹ کیبل کے ذریعے یا ایگزٹ کیس اسٹیشن کیسے کنیکٹ کریں۔
کمانڈ لائن انٹرفیس تک رسائی حاصل کریں: ٹرمینل ایمیولیٹر پروگرام کھولیں ، مثلاً PuTTY ، اور ایکسیس پوائنٹ سے کنسول کنکشن قائم کریں۔ مطابقتی سیریل کنکشن ترتیبات (باڈ ریٹ ، ڈیٹا بٹس ، پیرٹی ، اسٹاپ بٹس) کا استعمال کریں۔
پرائیوی لیجڈ ایگزیک موڈ میں داخل ہوں: کنسول کنکشن قائم کرنے کے بعد ، اینیبل کمانڈ ڈالیں اور ایگزیک پاس ورڈ فراہم کریں (جب کنفیگر کیا گیا ہو)۔
گلوبل کنفیگریشن موڈ میں داخل ہوں: پرائیوی لیجڈ ایگزیک موڈ میں ہونے کے بعد ، کنفیگریشن ٹرمینل کمانڈ ٹائپ
Please My Channel and Pages follow Subscribe,Like and Share Thank You
====================================================================
1- Subscribe RU-vid: I Like Pathan
bit.ly/40XO3O4
_________________________________________________________________________
2- Subscribe RU-vid: Zila Network
bit.ly/3MjBNUg
_________________________________________________________________________
3- Subscribe RU-vid: Zila Pathan Vlogs
bit.ly/4365yxJ
_________________________________________________________________________
4- follow my Facebook Page:Comedy TV
bit.ly/3naFnpE
_________________________________________________________________________
5- follow my Facebook Page:
bit.ly/3Np8fox
_________________________________________________________________________
6- TikTok Page Like and follow:
/ like_pathan
_________________________________________________________________________
7- WEB: zilapathan.blo...
====================================================================
Putty Software , Active USB-COM Port and Script Link:
bit.ly/3NxnkEy
Putty Comments
1: ena
2: Cisco
3: config t
4: int bvi 1
5: ip address 192.168.150.1 255.255.254.0
6: exit
7: exit
7 сен 2024