LONG TERM COMMENTS: Apparently since these vids came out, demand has soared. But increasingly customers have complained about not being able to contact Clake as they are too busy with production. I'm not sure if this has improved or not... but just be aware it could take a long time to get any response if you have problems. I've had quite a few customers contact me saying they could never get the Clake guys to answer emails... and I passed on these messages. They just said it's best if customers ring directly between 8am to 9am (Melbourne time) before they hit the factory floor. This could be tricky timing for overseas customers. Some of us find it really hard to install... especially when bleeding the system. I'm a hopeless mechanic and had to take it to the factory to get it done properly. Probably best if you are very handy at that sort of thing. When I tried to fit it to my next bike eventually I gave up and sold it, despite good phone support from the Clake guys. But I wasn't going to drive 1600km to have them get it right. 😥 Since doing this vid Clake have updated their installation instructions which has helped many apparently, the earlier instructions weren't very clear. CLAKE 2 or PRO LEVER? The Clake Pro Lever? Unfortunately I never got a chance to review this. Both very similar... the Clake 2 has the "clutch only" option with that inside lever immediately. The Pro Lever, move a little selector across to get the "clutch only". Clake 2 suits better if you will regularly swap between "clutch only" and "clutch/rear brake" when riding as you just move your finger across, otherwise the Pro Lever's simplicity could be the better choice.
I really enjoyed my clake pro but the loss of riding weekends spent in the shed trying to bleed the thing put me Off and I sold it. It’s a shame they haven’t spent the time to set up a dealer network across the country to assist in installing it. I’d buy another if I could guarantee it would be bled up right.
It's time for you to try the Clake Pro! I was worried the Clake Pro might make it harder to wheelie well as the transition between clutch only and brake might interfere with your balance when going from feathering the clutch to braking. I'm still deciding if it's worth the dollars.
Picked up a Clake Two can't wait to try it. They must've gotten your message because Owen at Clake responds to my emails within 24 hours everytime! I'm in the states so I don't usually call.
I know itsIan old video but to anyone looking at the Clake. Yes its a bit painful to bleed but cable tying the lever overnight to the bars solved the issues I was having. My second hand Beta came with Clake 2 and a spare but bent Prolever. Never really liked the 2 lever setup as years of road riding big twins with bad efi fueling had me ride constantly with 2 fingers on the clutch at all times. I use it to modulate the power at low speed and do it constantly on the dirt. I finally got a new prolever for it and I love it. Its just a regular 2 or 1 finger clutch but as soon it gets about half way to the bars and the clutch is fully disengaged it starts working as a brake. Given the price I'd be hesitant buying one new however I really dislike riding without it now. Bar mounted rear brake just makes so much sense. Autoclutch on the other hand meh, not sure what purpose that serves and I use the clutch as a secondary throttle anyway so never really stall it. Definitely worth a go though if you can afford it or find a second hand one. Clake should have a think about some simple written instructions explaining the different cams and what their numbers mean though. I had to watch the videos over and over and take notes. Not the most well documented product.
Great products once they are set up. But I agree Rupert, the documentation could be better. It seems to be common with a small business where they ge overwhelmed by demand then never seem to have the time to get their support fully sorted...
One would think that there is a fine target to hit when adjusting overlapping of brake and clutch - not enough overlapping and you get a moment where you lose your engine breaking before engaging the rear brake, to much and you slide your clutch plates or even stall. For backing it in (supermoto or flat track) it sounds kind of spot on! lock the rear and disengage clutch for downshifting with one pull and quickly release for a smooth transfer of brake back to engine breaking. After I finish modding rox risers and find lowered foot pegs I might give this lever a try.
+Ariel Rotem the clake 2 is quite popular in supermoto, and there are a few guys road racing with them as well. i'd love to still be using one but my arthritic fingers need all the help they can get so i'm using the clake one light clutch now.
FailsAndFights damn, i feel kind of responsible now. :-) i reckon you'll love it, everyone who jumps on my bike takes about 30 secs to get the hang of it then start raving about it. only thing is whether to go the dual levers or the single one (the pro lever). hoping to try that one next ride, woohoo.
FailsAndFights Yes. I think the company itself could not have advertised it better. Barry is one of us common folk and I trust his opinion more than anything. I guess he has never cared about receiving compensation. Not even ads on his videos :))
I can't believe the amount of people sooking about price. So much more control over your bike with the rear brake on the bars with the bonus of a lighter clutch. Riding improves so much more. A quality product made in Oz. I guess some people can't see cost vs reward. The same people who cry about everything is made overseas....🙄
Thanks for this video. I saw it and got interested. I ordered one and installed it. It's just really great. For me it's a game changer. I'm 6'4" and have size 16 feet. Using the rear brake was always a funky with my side on the relatively small frames of dirt bikes.The freedom the lake 2 gives to how you use your legs is just great. Cakes video installation instructions are bloody great too, with the added charm of a nice thick Aussie accent! It's expensive, but not over priced, the workmanship and design that went into this product is worth every pennie. I went into a wobble / fishtail on a fast section today and I attribute me not going down to the clake two. I gave the bike a stab of rear brake and clutch to go from fishtailing left, right, left etc to swinging over to a slide on one side, I then threw open the clutch and gave it some throttle and came out of it. I would not have been able to reach the foot brake as the fish tailing had thrown both my feet off the pegs and I needed to throw my legs back to help stabilize the bike. I also like the fact that I chose the set that keeps the rear brake on the peddle as well. Found it nice to stab the rear brake with my foot here and there.
Looks like a good bit of gear Barry, very well engineered, we run Rekluse auto clutches and LHRB and ditch the foot brake completely, about $70 for a custom brake line and use the KTM clutch as the master for the rear brake however we need to use a spacer to increase the fluid volume. However the Clake looks like a great option to this setup
Reece Tasker a rekluse and LHRB, would have jumped at that a year ago when i was running a rekluse exp! but getting into trials forced me to start learning good clutch technique so figured i may as well do so on the dirt bike too. :-)
Thx for another good review Barry. Besides the fact that the Clake master cylinders are expensive, they do not fit in plug'n play if one uses original KTM handguards. I mailed my concerns to Owen, but he was pissed (at least I think so) and didnt even answer. The handguards you use are not those from KTM-power parts and they seem to give a little more room. Even though you had to add a bushing to gain some extra space. However, the Clake parts are cool and innovative, no doubt. Cheers from vis-a-vis ;) Steve
great to hear marco! i hope the fitting went okay, i've told clake they badly need to update their instructions and they agree but are still too busy to do anything yet. :(
on a 690 enduro with ABS was really not so easy but I've managed. I have to say the cable lenght was perfect. Using the brake to get traction when starting on steep climbs is a blast. Now I really have to learn slow weelies :-)
ill definetly say this. most humans use our hands and fingers much more than we use our feet and toes. it only makes sense that a rear brake that is hand operated works better. As a mountain biker now just getting into riding a dirtbike, I can attest to the accuracy in control that using your hands can give you. Now i just wonder if i can figure out a setup where my front brake and rear brake are both on my bars, and my rear brake is on the right while the front is one the left (just like my bike). thatll be hilarity when my buddies ride it.
I have a fused right ankle,,,Rekluse has allowed me to ride to his day, left handed rear brake, but I miss using the clutch,,, Going to try your product,,Hope it helps me ride into the future. I AM 61 YRS OF AGE.
the clake two does make the clutch lighter to some extent ron, but it's the clake one light clutch that is very light. not sure if they've fixed their supply problems though, there have been lots of reports about delayed deliveries and trouble getting support since they became very busy.
CLAKE 2 or PRO LEVER? Both very similar... the Clake 2 has the "clutch only" option with that inside lever immediately. The Pro Lever, move a little selector across to get the "clutch only". Clake 2 suits better if you will regularly swap between "clutch only" and "clutch/rear brake" when riding as you just move your finger across, otherwise the Pro Lever's simplicity could be the better choice.
Can anyone explain to me why one would not want the Clutch disengaged when using the rear brake? I am just wondering. This is a nice tool, but in NZ its costing $1450. My bike is only worth $2000.
i dunno, after racing MTB for some years, I think it'd take some getting used to having the brake levers control the opposite positions (left is front and right is rear)
Tried it, just couldn't gel with one finger on the clutch, made arm pump worse in the snotty stuff, and modulation harder in my case. Loved the left hand rear brake though, a 2 finger clutch version would be ideal for me, but I'm old and habits are hard to break.
+v4magic damn that's a pity v4magic. i hope you didn't lose too much selling it? there are rumors of a two finger version coming out but nothing confirmed yet.
+CROSS TRAINING, ENDUROCROSS & ENDURO TECHNIQUES I've just listed it on ebay, so I'll have to wait and see on that one. I should mention I broke my left arm in 3 places as a 15 year old (on a dirt bike!), so my arm isn't as strong as it should be My experience is definitely not typical and I don't mean for my comments to reflect badly on the product, it just didn't work for me. a 2 finger version?? That's interesting...
That's really cool, wish it wasn't so expensive though. I can't afford it :( Maybe someday... I also wanted to say thanks for all the videos, it's helped my technique tremendously.
Hey Barry, long time. Since you last replied to a comment, I've broken my back (T3/T4 compression fracture, November '21) and my leg (tib fib, Nov '22). Following your path. Anyway, question is, is your amazing wheelie skill somehow connected to using a LHRB? I've gotten pretty good at wheelies, but struggle with RB control through a boot - went from Alpinestars tech 10 to Gaerne (GAH ERR NEH yeah) SG12, still can't get any modulation. Anyway, thanks as always, love all the vids and come back to them frequently and recommend heartily to all mates. Cheers.
Bummer, any surgery, Donovan? Body cast? And what's your prognosis? I've never used the LHRB but admit it would be handy! I just did the exercises in the covering rear brake training vid over and over. And I still do it a few times every ride when warming the bike up to stay up to date. You can get modulation with any heavy duty boot, it's just practice.
@@crosstrainingenduro Prognoses all good, fully recovered from the back, leg is slowly getting there (leg recovery less fun than the back). Cheers for that; will keep practicing with the boots, but might give a Clake or an Ox Brake a whirl at some point ;-).
I found instead of forking out all that money for a clake (which i must say is a great bit of kit) pivot pegz were my god send for rear brake control and only cost a fraction of the price. Still couldnt beat a hand operated rear brake but.
joshonolo actually that's a good point josh and possibly a good budget way to make a difference. i've only ridden on them once and didn't like it but i know everyone says you need to give them a decent trial... maybe i should review a pair?
So you got to tell me, what's the bungee cord on your helmet for? Lol. Btw thank you for all your videos, full of knowledge and the humor is priceless.
Thanks so much for bringing this piece of equipment to my attention. I have a Rekluse and LHRB set-up, but with two conventional levers ergonomics is always a compromise and definitely not intuitive. After some excellent and swift communication with Owen, I placed my order today. Keep this Aussie engineering coming guys! (pivot pegz, steg pegz, clake two)
Husa501 cool, it takes a few hours to fit and the bleeding is time consuming but i think you'll love it... as you say it's like your setup but the ergonomics are so good with this! please let me know how it works out for you.
CROSS TRAINING, ENDUROCROSS & ENDURO TECHNIQUES Update, took awhile before it arrived, caused by high demand and limited production capacity (as Owen explained me). Installed it just in time for a 3 day enduro trip in the Czech Republic Giant Mountains. (bleeding the rear brake btw was a real b#tch). But what a great piece of equipment! So much control, especially in difficult conditions! Love it, worth every €/$ imo.
Question regarding this system for "cross training". At about the 1 minute mark you mention you ditched the rekluse auto-clutch as it is "cheating". How do you feel a hand operated rear brake is not cheating in this respect? Isn't the intent to keep the controls as they would be on any other motorcycle, thus sharpening skills that map to any bike?! I struggle mastering the foot op rear brake on my bike. I think I plainly see the advantage of having it as a hand control instead. But I worry it would make me depend on having a hand control available. Which it won't be on most machines I ride.
+Colin Samuel personally i think anything that gives you extra control is great... i use 'cheating' in inverted commas because there are always diehard guys who think almost any non-stock mod is cheating. when my middle aged fingers finally can't cope with the clutch anymore i'll happily revert to an autoclutch.
Looks fantastic, was sold on a rear handbrake already and contemplating a dual caliper set-up but this looks very well engineered May see if they post over the pond :)
WRLondon they do, apparently when i posted that review they got swamped with orders from the usa. might be worth emailing them first to see if they've recovered from the flood of orders. :)
Great video, and the product sounds incredible. So i headed over to their website to check out the price. Wow, i can't stop laughing. the price of this thing would be about 1/8th the price of my entire 300xc-w. Ill stick to a regular clutch!
yeah it kills it for most people kevin. it would be way cheaper if they outsourced the manufacturing but they don't trust others to maintain the quality control. 😥 it really started as bling for people with disabilities of course, so in that case the price tag doesn't seem so bad. but for the rest of us.....
Hi Barry, did you manage to review the Clake Pro? I've searched for the mentioned review but found nothing. The Clake Pro lever seems to me like a better choice over the Clake 2, but what sounds great in the product description must not necessarily be a better choice...
Nice video, thanks! I'm in the market for a LHRB primarily for motard use and better wheelie control, though I'm not sure if the Clake two is right for that. Something about this setup that scares me is that the RB and clutch work in unison. Correct me if I am wrong about this, but if you want to apply RB at the balance point, the clutch is also engaged- meaning I can't alternate between feathering the RB and applying more throttle. Or have I misunderstood the mechanics of this device ?
surg23 with the clake two, you have two levers. one does just the clutch and nothing else, moving the finger slightly and the other lever does the clutch then increasingly the rear brake. you can use different cams to choose the degree of overlap between clutch and rear brake, if any, and how fast/slow each is applied. the pro lever is extremely similar but just has one lever... there's a small toggle you can flip while riding to choose clutch only, or clutch/rear brake as above. hope that makes sense. i haven't tried the pro lever yet but a mate of mine has had one for years and loves it.
Oh I see! Is it possible to have the outside lever setup to just actuate the RB ? I just don't like the idea of being forced to engage the clutch when applying the RB. Thanks!
surg23 could question, possibly... i'd suggest asking the clake guys about that. but the current setup works really well as an anti-stall measure, but if you want just the brake and no clutch action you can always revert to the rear brake lever if you keep that installed.
I'm 57 and just starting out. I'm gonna cheat. I just put a Radius CX clutch on my KTM 150 XCW TPI. Which Clake brake would you put on? I don't think I need the clutch lever.
When having two break leavers on the handle bars it would be nice to make it like a bicycle where the right leaver is the rear and the left is the front, did you find that it was hard to get used to??
Apparently the lever is interchangeable but I sold the Clake 2 years ago so no chance of testing the Pro Lever anymore. I simply couldn't get it to work on a new bike, despite long phone calls with the guys at Clake. Way beyond my mechanical skills lol.
Long time watcher first time commenter... So watched a few of your videos this one caught my attention due to breaking a couple fingers on the left hand 6 months ago negotiating unsighted water filled 4WD holes after clearing a water bar... I also seen your video on the CLEVER Lever. I bought the CLEVER levers both brake and clutch simply because they were a cheaper option. Loves the brake lever its a keeper however still having issues with clutch. I am on a 2014 Husky FE350 known for having a heavy clutch... Can you recall any difference between the Clake and CLEVER lever??? Cheers!
+Matt Taylor i think the clever levers are handy for slightly lightening the clutch, matt. i found they reduced clutch pull by up to a third initially but to fully disengage the clutch it still needed about the same pressure as stock. plus you had to pull it all the way into the bars. way more expensive, but the clake one light clutch is ridiculously light, about 75% easier and doesn't have to be pulled into the bars.
+CROSS TRAINING, ENDUROCROSS & ENDURO TECHNIQUES No worries thanks for the speedy reply!! So the Clake can be adjusted to fully engage without pulling all the way in? Is this standard or is part of playing with cams? My main issue with the clutch is the initial reach, thought the clever lever may of helped by changing my technique to the single finger on the clutch rather then my usual 2 finger technique but still have the issues with lack of strength in the fingers.... Will have to put this on the shopping list!!
+Matt Taylor the clake is set up to engage and disengage at roughly the same points as a stock clutch, but with just way less effort. so the handy thing is you can adjust it in for small hands and make all sorts of adjustments. i'm actually not sure if you can fit different cams to change the way it engages though matt, maybe check the website?
I like the look of it, coming from mountain biking I think it would be very helpful. But can regular levers be made to fit the system? or are there cheaper replacements? I tend to break/bend more than i like to admit and it seems a bit pricey to be constantly changing them...
grassy lands no way you'd get a standard lever in there, they push against cams to get a much lighter pull but without having to pull further... i can't find any reports of someone braking a lever or any part of the assembly but i'll try to get a figure on replacement costs and annotate the vid accordingly.
I've watched your review of the Clake 2 over and over. I definitely want one, but the buy in is painful! I've actually wanted a LH rear brake for a long time, because downhill right turns can be sketchy! But now trying to pick up some cross training abilities, I can see how the LHRB would provide a measure of security and natural feel to covering and using the rear brake. Plus a super soft clutch provides even more control over the beast that is the 500 EXC. So I notice you have only one single lever in front of the left hand grip on the Principessa, and it's not a Clake. Do you plan to mount a Clake, either the 2 or perhaps the pro lever, on the red beauty? I'm most interested in your current opinion on this matter!
gncc1race definitely getting a clake 2 fitted to the beta, one of the clake guys is coming to brisbane soon and offered to help fit it which is a bonus, i'm terrible at bleeding normal brakes. :-(
Cool! That encourages me as to the investment. Fortunately I'm fairly proficient mechanically. I've seen a bunch of Clake tutorials and am confident of switching it myself. I have to of course... Clake representatives aren't scheduled here in Alaska until 2027. ...Maybe 2026.
So I just took a peek at your FB page... The super moto photo has GOT to go! LOL!! ...When you were in your supermoto phase, did you have to get both ears pierced and the obligatory tribal arm sleeve tattoo? LOL!! Actually I have nothing against Supermoto except that it's a waste of perfectly good dirt bikes! But anything having to do with bikes is cool, so... Except the Nazi bikes. They weren't cool. I mean they were, but the Nazi's weren't... Well, you get it!
Hey! I have an unmuffled Harley in the driveway! ...Ok, no I don't. Feigning indignation, sorry! LOL!! I commuted extensively on my first street bike and did put loud pipes on it to help wake up inattentive drivers. But after about 90,000 KM I was TOTALLY over loud pipes! Eh what? What did you say?
Chris Jones not sure on the replacement cost chris but i might email them out of interest. i feel my barkbusters are going to protect it pretty well though, and the mounting bolts are loosened off enough that it will all swing around with a direct impact... fingers crossed. :-)
***** as per the vid some hand guards need a spacer and a longer bolt, mine did. i suggested to clake they put these in their kits actually and i suspect they will, from what i read on the forums they are very client-focused and respond to feedback fast.
Has by any chance one of you tried the PRO lever? It looks less bulky and you can do everything with one finger, problem is.. will you be able to zap the clutch to wheelie over water/gaps while at speed?
yoshyoka as per the video the guys at clake have offered a prolever to try if i do a review on it so will be dong so in the near future. will be interesting to see how they compare! i assume it will be the same functions but easier operation with the prolever but just a bit less ease swapping from clutch-only to clutch & brake functions.zapping should still be the same i imagine...
+maddash1337 that's interesting, maddash. perhaps there are problems with clutch modifications in australia for street riding but no one has discussed this. i don't know the laws in germany...
FailsAndFights man, that's a tough decision! do you upgrade bikes often? the clake can be transferred to just about any bike, whereas the rekluse is often model or even year specific. but then hill climbing is so easy with the rekluse if you don't like clutch work.
CROSS TRAINING, ENDUROCROSS & ENDURO TECHNIQUES Something to think about... I do like having a clutch as well as an actual brake lever so I'm thinking I'll go with the Clake
CROSS TRAINING, ENDUROCROSS & ENDURO TECHNIQUES I'll let you know as soon as I can get one ;) I need a new clutch and perch anyway because I hit a tree hard the other day... made for an awesome video though!
So on a forum a few years back you were talking about the clake 2, and you mentioned that Melissa had purchased the Clake SLR, wondering how that worked out? The Clake 2 looks amazing, but I was looking at the SLR as the clutch and my stock brembo master cylinder as the brake (Clake recommends this as the SLR is lighter than the stock clutch) Figured I'd top it off with a midwest cleverlever as the brake and be about $250 short of the Clake 2. Any one have thoughts on this? or am I better off not being cheap and buying the 2? I have a 2015 FE501s, if that's relevant.
+william hackleberry you'd have to chase melissa for her thoughts. i don't feel comfortable making recommendations at all william as all riders vary so much and i couldn't really add anything to what i've already said in all the vids.
Finn Sillibourne an awesome bit of kit! i'd suggest emailing them first though, apparently they got snowed under with orders when the vid appeared and they are still trying to catch up. probably all good by now but worth checking. :)
So I am about to buy a Clake 2 and I thought of something right as I was about to purchase it, I am going with the hand operation only and wondering about how the brake light switch is replaced?
Can this be used on a road motorcycle. I suffer from abs in my left hand and I'm currently looking for a duel level system to be put on the throttle side. So I can operate the clutch and front brake.
Would you say the clutch pull is even lighter than a standard KTM hydraulic clutch? (KTM 500 EXC in my case). I am debating wether to go for this or the Rekluse EXP 3.0 - but the Rekluse feels a bit like cheating! I imagine the one finger clutch + hand operated rear brake would be more fun than the Rekluse as long as it is light enough to reduce arm-pump :)
kullsyreholdig01 way lighter than a standard ktm clutch, it's more on par with a trials bike. i did use a rekluse for a year but realized i wasn't really developing my skills. but a rekluse is fine if you want to only take your riding to a certain point then just chill out.
CROSS TRAINING, ENDUROCROSS & ENDURO TECHNIQUES still sort of cheating :P A guy I ride with has this same set up on his 500 excf and it took a massive slick downhill to notice he's paddling feet down with the rear locking up and the bike running?!?! would be a great help to riding for sure, makes the transition for bike riders easier too as I always struggled with my foot positioning to cover the rear at times - something I'm working on bike/body positioning. the design is awesome! price point is the killer tho especially since I tend to break the nice things I get.. but I will ask for a ride of the 500 next time to test it out you put up some awesome vids, keep it up mate.
Very cool bit of kit man! Couple of questions: Do you still have the rear foot brake lever there as well or do you solely use the hand operated one? You said you gave up the Rekluse as it wasn't helping your skill levels. I am going through the same thing right now. A mate made a hill the other day that I didn't and I don't like giving excuses or anything, but I know that him having a Rekluse really gave him the advantage and got him up the hill. I was determined to go home straight away and order a Clake clutch myself, but then I thought, well isn't that giving me the same sort of advantage over other riders who don't use a Clake and therefore not helping me with my skill levels also? I'm not "having a go" by any stretch of the imagination, I just wanted to know your thoughts on this.
JoeJoe Moto i've kept the rear brake, i can see why some guys ditch it but i just like having it there for some reason! i reckon some guys would still see the clake two as "cheating"... but if it is then it's a much much reduced level. you still have full manual use of the clutch, and the anti-stall feature only kicks in if you are using the rear brake, and are using the outer lever. to me it's just a much more intuitive system - we all grew up riding bicycles with the left hand doing the rear brake and to me this is just a logical (if bloody expensive!) extension of that. :-)
CROSS TRAINING, ENDUROCROSS & ENDURO TECHNIQUES Thanks for the explanation mate. I agree with you hey. It's still a clutch, just a bit of a different one hey.
JoeJoe Moto well... must admit i still think i'm cheating a bit. i mean jarvis doesn't use one, and he's my personal deity at the moment. :-) but at my advanced age i think i'm entitled to a smidgen of cheating!
CROSS TRAINING, ENDUROCROSS & ENDURO TECHNIQUES hahaha yeah, in our group of riders, we all have what we call "Cheat codes", one runs a Rekluse, two of us use trails tyres etc. I know what you mean about Jarvis though, it is why I put the first comment up. It would be awesome to be the kind of rider that no matter what bike you got onto, you could still do all the same stuff, right out of the box without the "cheat codes"!
Hi, been following your channel for a while now. I'm trying tobdecide whether to buy the clake one light clutch or save up and get the clake 2. Would you suffer a heavy clutch for a few months in order to get the 2 over the 1? Or would you buy the 1 and save up longer for a 2?! Thanks, I've been trying to decide for a while now and have saved up enough for the 1 but can't decide as I've never used or seen either in the flesh. Thanks again
+Jams g that's a tough one jams... for the sort of technical riding we do the clake 2 is absolutely brilliant. i'm sure it would be great for some aspects of endurocross too. i'll list what i think the benefits of the clake 2. i think most of these would apply in your case but possibly not the last one? we use it when bull dogging down hills or upending the bike for tight u-turns etc: - rear braking on right hand corners with your leg out for stability - rear brake control is not affected by body movement or terrain - much finer control of the rear brake for maximum traction - less stalls due to the rear wheel locking up far less often - full rear brake access even when not on the bike
Simon Eldridge i kept the foot lever as well. some guys do away with it completely and very happily, but being an old fart sometimes i'll revert to the foot pedal if i'm getting a bit of arm pump. and occasionally on very long downhill runs my index finger gets a bit sore from holding the handbrake on and it's good to revert to the footbrake... although way less feel in the brake then!
+Kevin E (KevinE) not in the foreseeable future. i'd say the main thing is the clake 2 allows instant choice between clutch only and clutch/rear brake options if you move your index finger between the two levers, something i adapted to instantly. the prolever suits better if you are more likely to stay in one mode or the other as you need to throw a little switch first... plus you've got a 'normal' lever to use, particularly if you use more than one finger on the lever.
+CROSS TRAINING, ENDUROCROSS & ENDURO TECHNIQUES ...At first thank you for your kanal channel is fantastic! Help me few times even Im 47 old men. I would like to asked you: clake pro lever, it is possible to set the range of motion? I mean when I push the cluch at first it will move to halfway and after rear brake start work. Like 50% to 50% or 30%cluch and after 70% cluch and brake range of motion? We are riding very steep hillclimbs and "wet stone streams" so should it help? Thank you for answer. Hope you,ll understand my poor english.
yes, you can push the lever across to reduce the rear brake action. you can also change the cams inside the prolever to adjust the range of motion, for the clutch and brake.
Eventually sold it with one of my bikes. Used a Midwest lever and washers on the clutch springs for years after that. Just started using a Clake again on my latest Sherco.
Sweetman i think the $ are the only downside, sweetman. I actually visited melbourne recently and dropped in to see these guys and saw the manufacturing involved and can see they don't actually make much money on these... the intricacy and sheer amount of machining involved is incredible but they don't want to trust a chinese factory with the precision needed. :-(
It's a risk either way (home-made quality vs. costs) but hopefully their choice to make it a better quality product pays off for them in the long run. I never tire of your awesome videos man - Keep it up :)
Greg Farrell not yet greg, i'm not only a riding gumby but a mechanical gumby too so had trouble fitting it. :-( the clake guys are coming to my city soon for an even and said they'll fit it for me, how good is that?!
Do you still run this lever on your Betas? I'm useless with the foot brake, I have wanted a handle bar rear brake for some time now, as I come from a lot of mountainbiking in the past. Plain and simple I miss it.
i loved the clake 2 but arthritis and carpal tunnel made the rear brake too much work for aging fingers. :( i'm running the clake one light clutch now to make the clutch as easy as possible.
I bought a clake 2 and installed it and it works great but no hand guards fit on it... I have a KTM 300 2017 six days and kinda stuck, what hand guards did you use in the video?
that was ages ago, can't even remember now. almost everyone just uses a spacer and a longer bolt to push their handguard out enough... usually the clake 2 only needs another cm or space to fit. clake sell a spacer if needed but just a pile of washers will do the trick cheaply.
Is there any difference in clutch "lightness" between the Clake One light clutch and the Clake two? How light in the one light clutch compared to ktm's stock clutch?
MRKTM690smc the one light clutch is probably about twice as light as the ktm stock clutch. it's exactly the same as the clake two in terms of the clutch pull.
Good to hear. I can get a really good price on a rekluse and have been debating whether or not the one light clutch would be good alternative. The ktm already has a pretty easy pull and to make that even lighter would be great!
+Trail Bound co i've swapped over to a clake one light clutch now which is definitely adjustable, i'm sure the clake two was although i never messed around with the reach... i'd check with the clake guys to be sure though.
Joshua Guy done few rides since but fairly gentle ones as the ribs are still sore. all good though, still impressed with the grip despite the knobs rounded off now.
I've decided I'd try the medium compound to see how much more traction I get to my usual hard compound on my usual tyres. I'll also need new tyres before I ride to the Cape. I hope they last a good while for that reason :P
Looks like an amazing product, but at $780 minimum that's out of my reach. And $50 for a spare master cylinder and $100 for a spare lever, just seems a little too much
the only way to get cheaper would be move manufacturing to china and the guys said it would be a constant battle to ensure the quality needed for the more intricate parts. :(
Can you set this system up so it does not pull in the clutch when you use the rear brake as it would cause the bike to freewheel say into corners or am I missing something
+ishak roberts not really ishak as the point is to prevent stalling... BUT you can change the internal cam so that there's quite a bit of overlap between clutch and brake e.g. you would have engine braking as well until you pulled the lever in hard enough to start locking up the rear wheel. some guys set them up like this, others like me prefer to have minimal overlap.
+CROSS TRAINING, ENDUROCROSS & ENDURO TECHNIQUES Thanks for the reply. Maybe then that's a new product in the making one light clutch with a 3 finger lever with the clake slr running above, which you could make your own by just buying the clake slr and using stock clutch so maybe it may not sell enough to invest in producing it :-)
+Laser Born it's been asked and replied to in lots of comments... the clake 2 does lighten the clutch a fair bit, but my middle aged fingers are really struggling nowadays so i reverted to the clake one light clutch which is super light. at this rate i'll probably be back on an auto clutch within a year. :(
CROSS TRAINING, ENDUROCROSS & ENDURO TECHNIQUES Oh! So the clake 2 doesn't lighten it as much? Is it because its half way connected to the brake? If your hands are weakening you should get something to train them. (I personally use "Abilica HandGrips") My new bike is much stronger and therefore has a harder clutch, so i used these every day and now i can almost pull in the clutch with one finger. (But not for a long time, yet.)
+Laser Born yep, the clutch is lighter but then activating the rear brake does reduce the lightness. all the muscles are fine for making the fingers work, it's just the joints themselves being in the early stages of arthritis which you can't do much about other than regular exercise, good diet etc.
CROSS TRAINING, ENDUROCROSS & ENDURO TECHNIQUES Oh well, i guess maybe, just maybe, we will find a way to "cure" artheritis. But until then, you can atleast exercise!
George doubleyuh yeah i had my concerns about that too but once the barkbuster is spaced out it's no more exposed than a normal master cylinder. and i've got the mounting bolts slightly loose as usual so it'll twist if i did land the bike upside down.