Clipper blade care - Troubleshooting Clipper Blade Issues (part 2 of 2)

Подписаться 624

Просмотров 81 тыс.

50% 1

This video identifies common clipper blade and clipper problems and how to diagnose and remedy these issues to help keep your clippers performing and cutting optimally.
Recommended products to keep your clipper blades performing optimally:
H-42 Virucidal Disinfecting Spray: amzn.to/2mfXlF2
Andis Cool Care Disinfecting Spray: amzn.to/2myyayq
Wahl Clipper Oil: amzn.to/2lzjZUS
Andis Clipper Oil: amzn.to/2lESXww
Clipper cleaning brush: amzn.to/2m0e9PY
Andis T-Outliner Trimmer: amzn.to/2mjSFPd
For more information about clipper care visit us at kutaboveperfection.com or call Josh Freund at (708) 254-4209.

Хобби

Опубликовано:

4 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 59

@sarahdraydon3456 2 года назад

Thank you for an excellent video Josh - you have saved me from noisey clipper! Thank you from Sarah in Australia 😊🐶

@sheilasmith1109 3 года назад

I’m so pleased to find your videos! I’ve been so frustrated with the newer Oster blades NOT CLIPPING! I had no idea it could be my clippers! It has been impossible to find anywhere to send my blades in for sharpening. I’m hoping that I can send them to you so I can use this workhorse clipper once again! Thanks for the REVEAL! I’ll share with others I know who’ve experienced this same problem with new blades not cutting! It Could be the clippers! Thanks 🙏

@kutaboveperfection 3 года назад

SheilaSmith I’m glad this video found you and gave you more clarity on your possible clipper issue. When you’re ready I’ll be happy to sharpen your clipper blades and beauty/grooming shears also. My mail order sharpening is on my website. Thanks!😊 www.kutaboveperfection.com

@lk6762 7 месяцев назад

Fixed it. thank you

@Smokey66s 3 года назад

The brass screw hinge anchors pulled from body of my Oster 76 causing drive lever not to engage and severely rattle. New replacement housing replaced.

@1999BOARD 2 года назад

PLEASE HELP*** Hey this is a great video on troubleshooting! I have kind of a unique issue that none of my coworkers have seen before. My blade is noisy just like in this video. But all my equipment is brand new and what you discussed in the video doesn’t look like that is the issue. This specific buttercut #30 blade is making noise like that but only on my clipper specifically, not making the noise on my coworkers clipper. Other blades aren’t making that noise though on my clipper. I have slid out the blade and gave it a good cleaning but same issue. The #30 making the noise is also brand new with only a week of use. The ears look perfectly straight. And the latch on my clippers is tight. The clipper being used is the Oster A5 turbo, the blade that has the issue is a Buttercut 30. Again, Only this blade is making noise with this clipper.

@kutaboveperfection 2 года назад

I would have your clipper guy tighten up the socket to double check. if your clipper has a higher speed than your coworkers then that might show from the speed of your clipper a difference in noise . Without physically looking at your clipper with my own set of eyes that would just be an educated guess. Also make sure your blade drive is new to rule out any other variables. Keep me posted when you find out what it is. 👍

@biggeorgiou 4 года назад

I have changed the drive on clipper but 2 blades I have are still dragging

@kutaboveperfection 3 года назад

i'm sorry for the late reply, but it sounds like the blades need a proper sharpening or the spring tension is too loose on those 2 particular blades.

@lindaraidl663 4 года назад

my blade drive appears to work,meaning it goes side to side when switch is on,but when I snap the blade in place, the blade doesnt follow side to side. It fel and loos snapped down in pace. John.,not Linda above.

@juliagilson7269 3 года назад

Did you find a way to fix this? Mine is doing this too

@AB-zm4mj 2 года назад

Some of my blades are extremely noisy, I think they are too tight. What could be the issue/how to fix that?

@kutaboveperfection 2 года назад

noisy blades as I mention in the video are indicative of the sockets being loose and need to be tightened by your local clipper blade sharpener. You can also send them in to me and I can take care of them as well. also if all your blades are noisy it could be that your latch is loose or worn out and needs to be tightened up or replaced . I hope this helps keep me posted😊

@jonibelz6254 3 года назад

I recently inquired a canine fx dog clipper as taking the white cover off to clean the hair out it was full of grease I mean full ...I cleaned it out best as I could ...but y was all this grease there is it suppose to be there ...took each part and cleaned with dawn worked very well ..so as to putting it back together do I put more clipper grease back in there

@kutaboveperfection 3 года назад

Joni Belz it wouldn’t hurt to put a little bit of red Oster grease on the linkage where the blade drive sits.

@jonibelz6254 3 года назад

@joniwalters2694 Год назад

Hi, i love your videos. they are so imformative. I do have a question though. I have an andis dog clipper blade size 10 ultra edge that is dragging and pulling the hair, but its a new blade. And the clippers I have dont make any other blades that I have do that. This is the only blade that does it. do you have anymore reccomnedations.

@kutaboveperfection Год назад

Thanks for watching my videos.! You might want to check the blade set back and make sure that the cutter blade is properly centered and not crooked on top of your comb blade. If that looks straight and even , then it may need to be sharpened or you might want to replace your blade drive first , if it hasn’t been replaced in a while. When you’re ready for Sharpening you can send them to me via my Mail order through my website. Keep me posted, thanks 😊 www.kutaboveperfection.com

@janetrusson5630 7 лет назад

i made the mistake of undoing the screw on my blades to change them and cant put the blades i took off together again

@kutaboveperfection 7 лет назад

Janet Russon , I recommend you have your local clipper sharpener reassemble it for you. Stay sharp!✂️✂️ kutaboveperfection.com

@alexandraferrer450 3 года назад

Which oil do you recommend for home use of Oster Dog clippers?

@kutaboveperfection 3 года назад

Alexandra Ferrer Andis ,Wahl, or Oster clipper blade oil for grooming clipper blades.

@sulu758 Год назад

Brand new Figura cordless and clipper keeps popping off. Recommendations?

@kutaboveperfection Год назад

If the blade keeps popping off then you probably have a broken tab on the bottom part of the plastic platform. You can take a picture of the bottom of the blade that faces inside the clipper and I can confirm that for you. My contact info is on my website. Thanks!

@ljacmfamily 4 года назад

brand new andis ebcII proanimal clipper and about an hour in to the grooming the clipper sounds weaker and is not cutting at all almost like it's run out of battery but it has an electric cord so it shouldn't. Any thoughts?

@kutaboveperfection 3 года назад

sorry for the late reply,but it sounds like a bad motor or the carbon brushes need to be checked. i'm interested to know how it turned out as to what the problem was.

@alishabeavis7688 2 года назад

My 7F blade wont cut but my 10 blade will. Clippers recently serviced and both blades have just been sharpened. Any ideas?

@kutaboveperfection 2 года назад

The latch that holds the blade onto the clipper may be getting worn out. The blades set back on the F7 may be off or just needs to be re-sharpening due to an improper grind. Other than that it’s hard to say without specifically looking at the clipper and the blade.

@alijandrothompson9129 3 месяца назад

New blabe 5 skip tooth , New clippers won't cut poodles coat

@kutaboveperfection 3 месяца назад

Make sure your blade drive isn’t worn, if your a full time groomer change it every 3 months minimum. Otherwise the blade needs to be sharpened because a lot of companies are having their blades made and sharpened over sees and the overall quality has gone done. I like Zolita and Heinger blades right now only. Send me your blades and I will make sure it’s better than anything you ever had. www.kutaboveperfection.com Stay sharp!

@cmatherne1696 2 года назад

I have Andis UltraEdge Super 2-Speed Detachable Blade Clipper, Professional Animal/Dog Grooming, AGC2, I used it once on a matted sheep dog, now it will not cut hair, I cleaned it after using it, oiled it, it comes on but barley cuts the dog hair and pulls the hair, I hope you can help me

@kutaboveperfection 2 года назад

When cutting through matted hair your also cutting through debris that most likely dulled out your blade. That’s why pets need to be combed out on a regular so they won’t get matted and need a shave down at the groomers. You might want to replace the blade to make sure , but I think the matted hair dulled your blade. I sharpen grooming shears and detachable clipper blades, so let me know if you want me to sharpen them. I have a mail order sharpening service on my website. wwwkutaboveperfection.com Keep me posted and thanks for watching my video 😊

@jennifernystrom9478 Год назад

I sharpened my blades on a stone, they’re nice and shiny smooth but they are pulling hair. My blade drive is fine. What else can be the problem?

@kutaboveperfection Год назад

I would stop sharpening your blades and have them professionally sharpened for starters. To sharpen a detachable blade there are about 15 different steps to service them to factory new condition. This requires lots of pricey equipment and excellent training with lots of experience. You tube barber sharpening videos are very misleading. To resolve your clipper blade issues I recommend sending them out to my mail order sharpening on my website at www.kutaboveperfection.com

@jimmyward2122 4 года назад

I can't get mine to snap in all the way into Oster turbo detachable new blade

@kutaboveperfection 4 года назад

Jimmy Ward while the clipper is turned on, put the blade on the hinge and use more force to close the blade onto the clipper while it’s running. The blade socket might be a little too tight, that happens.

@GayleGrantDocGrant Год назад

put on brand new Andis ultraedge 1.5 mm, #10 blade on new Andis clipper..will not turn on..all other blades work fine so it's something wrong/bad w/this blade..any help would be greately appreceiated..thanks!

@kutaboveperfection Год назад

Most likely the ears of the socket is set too tight so when you close the new clipper blade on to the clipper nothing happens. While the clipper is running I would use three or four times more force to close the clipper blade onto the clipper, Sometimes a tight socket will close completely and should start working at that point. If that doesn’t work send it back for a new one.

@GayleGrantDocGrant Год назад

@@kutaboveperfection Thanks very much, I'll check that out.

@marciaabram6510 Год назад

how do you replace the parts you identify as a problem?

@kutaboveperfection Год назад

I recommend having your local clipper sharpener replace the worn out parts.

@mahfujurrahman425 5 лет назад

When I set the blades, My Kemei KM 3580 isn't rotating. But when I remove the blades then the motor is rotating in actual speed! Couldn't find the problem! Even some blades work, while some are facing the problem!! Confused!

@kutaboveperfection 5 лет назад

Mahfujur Rahman You probably have a bad gear or link inside your clipper. Have your local clipper guy fix it for you.✂️✂️💈🤓

@mahfujurrahman425 5 лет назад

@@kutaboveperfection thank you... But here I don't have any local clipper repairing guy. You can advise me what's the actual problem so that I can give it a try. 😎 I can move the clipper by hand, no stucking issue...but does not move after setting to the motor!

@ksahman98 3 года назад

I have bought a brand new oster 97. I have oiled the new blade but it rattles. Is that normal? Or do i need to adjust it?

@kutaboveperfection 3 года назад

ksahman98 Based on the video most likely your socket is loose , and the ears of the socket need to be bent back again at a 90° angle so they stay tightly fitted to the latch of the clipper. Have your local clipper blade sharpener reset the socket and try it again. Hope that helps!🤙

@ksahman98 3 года назад

@@kutaboveperfection I will try that, thanks!

@jamesdowney7880 3 года назад

I’ve a brand new supra and 00000 blade that is catching any ideas ? Thanks

@kutaboveperfection 3 года назад

Check the blade drive to see if it’s worn. Also make sure your latch that holds the blade on isn’t loose either. If those two things don’t work then you might need that blade to be resharpened. Factory blades are using automation sharpening /AI, can’t do what a human can do😉 I have mail Order sharpening through my website for shears and clipper blades. www.kutaboveperfection.com Keep me posted! Thanks 😊

@selenaguerrero123 2 года назад

I recently dropped my clippers and now it has a rattling nose and does not feel to be cutting 🤯

@kutaboveperfection 2 года назад

Depending on what type of clipper you have , whether it has detachable blades or non-detachable blades, I would imagine the blade assembly has been thrown off. I would have your local clipper blade sharpener have a look at it to remedy issue. If you don’t have a specific Sharpener for that you can send them in to me through my website. www.kutaboveperfection.com

@sugarnewf2 3 года назад

I removed it and now I can’t get it back on help !!

@kutaboveperfection 3 года назад

what specifically did you remove?

@pambenoithamm9630 4 года назад

Why won't my blades snap onto my clippers

@kutaboveperfection 4 года назад

If its the correct blade for that type of clipper then the socket of the blade might be a little tight which requires you to use more force when closing the blade back on to the clipper, and if its a detachable blade then make sure the clipper is running before snapping the clipper blade back on the clipper. If you need further help it's best to contact me through my website. www.kutaboveperfection.com

@dickiemarra6518 3 года назад

My clipper blade won't lock in??

@kutaboveperfection 3 года назад

Dickie Marra, Your socket or spring may be bad or or your hinge with the locking spring. I would recommend having your local clipper blade sharpener take a closer look and repairing the issue.

@lisalyman9353 3 года назад

After only using on my standard poodle a few times the blade well not cut her hair. I paid around $300.00 for this km10 wahl, what a waste of money.

@kutaboveperfection 3 года назад

It could be a clipper blade issue if the cutting speed of the clipper is fast enough. if it's a cordless clipper keep in mind new tech. needs more time to get the kinks worked out before it's considered reliable.