Comparing SFP+ 10 Gigabit Connectors: LC Multi-Mode Fiber, 10GBASE-T, and DAC Cables. 

The test on SFP+ connected in one end into an SFP port, is what I needed! Great channel. Thanks a lot!

I've been using 10GTEK for years now and LOVE it... amazing price and QUALITY product!!! Works without any issues, never had a failure.

Wow, I literally was looking at RJ45 SFP+ adaptors today. I didn't know if they existed, just googled to see if they do, and found similar amazon products, then this video. Perfect!

Watching from Iran. Very informative. Thank you. \m/

Nice video! Thanks for sharing. I am very close to purchasing my first 10G switch (MikroTik) and first SFP+ transceivers!

Thank for helping not make bad decisions

When I want to sleep I go to this kind of video, quite a relaxing video and I’m learning as I sleep ;-) I’m a network guide needs to sleep. I dream in cables ;)

Another good supplier of SFP/SFP+, fiber, DAC etc is Hummingbird Networks. I have tried FS store, Amazon, and Hummingbird. I like Hummingbird because of their great support. You call them to determine if their products are guaranteed to work for a given switch and you get a firm answer. If they don't know they will sometimes send you a trial device. If it works, you pay for it and keep it. If it doesn't work you simply return it. Can't ask for more.

I run 2.5G Base T from my main rig over CAT 6 to a Mikrotik branded 10G transceiver on a CRS305, no problem negotiating at 2500 and I've gotten very close to that in sustained transfer to or from my NAS.

Excellent Knowledge from your Video~~~Like it~~

Nice video! Thanks for sharing.

This goes back about 10 years, but the last time I talked to anyone at Fiberdyne, they said they had a new user applied, glued connector for certain types of fiber. The person I was speaking to said that losses were nearly the same as a fusion splice. I haven't needed more fiber for my small system, so never looked into it. And their prices for custom length bundles terminated to customer specs. were so cheap that it generally isn't worth looking into those connectors. 10 years ago the 6 pairs I bought were about $150 for about 130 feet, might have had a nonprofit/educational discount applied.

We've been using 10Gtek transceivers for both ubiquiti and HP procurve / Aruba switches for 2-3 years. Haven't had a failure yet.

Great video!

great content!

Run iperf if you want to get a great idea what your network speeds are. Perfect for fine tuning especially with pfsense but higher throughput is best with TNSR.

(Traditionally) branded equipment (Cisco, HPE, ...) is more "picky" about modules you can install into them and accepted modules can be much more expensive as well.

i'm just starting to upgrade my home network to 10g and got one of those mikrotik switches coming! i'm trying to use the direct attach cables when i can to reduce heat but will need at least a few of the rj45 modules. i actually already have cat7 and cat8 cables because they were cheap and i didn't need very many, but this is a pretty old vid haha

The MikroTik S+RJ10 SFP+ module will do 10M/100M/1G/2.5G/5G/10G, but I don't know if they'll work in a Ubiquiti switch.

an idea for your next project. rgb lan cables and if you can control the lights in them you get even more kudos for doing that

NOS cisco 10 g adapters under $15 on ebay used hundreds of them

I'm working in a Datacenter as engineer and if a costumer asks for MMF connects I just show him the door or hit him with my SMF/E2000/APC whip. TLDR: Use Singemode Rant about MMF: From an investment standpoint, if you still have OM1 (gray) cableing, rip it out. If you have OM2 (orange) or OM3 (blue) ok. Don't buy OM4 for new long runs over 30m, it's ok inside a rack but it's failing to often. Don't be hyped about OM5 - to expensive and in 850nm it have more lost than OM3/4 because it's made for WDM SFP's with multible colored waves in one fiber. For new installs, use SMF and splice them to an APC Connector LC/SC or best E2000. Yes you need matching patch cabels for it, but if you forward a fiber link from your carrier through a building to your office via multible patchrooms, you will see the difference. Yes the SFP's are more expensive (20€ vs. 26€ @fs) but in the future if you upgrade to 25/100 or 400G. 400G QSFP-DD LC Duplex with 10km LR4/LR8 are on sale now (4000€-10000€ per SFP but 400G!!!) Even if you only need 100G at the moment or even only 10G, you don't want to replace you pre installed cabeling only the SFP's. (100G is @ 1400€ for a pair of SMF QSFP28 Modules) Also most QSFP-DD are SMF only. I normaly compare vendore SFP's with FS or flexoptix pricing and then choose what I need. If I need max. compatibility because I sell them to carriers if they have a broken one and need a replacement now - I choose flexoptix flash them and it works. If you build a office, just run fiber most of the way, pace a switch where your users are or plan floor tanks with space for switch, patchpanel, cable etc. Yes a fusionsplicer starts at 2500€ and easily go up to 10000€ but when I had the first one with a raw 12core cable on hand I had figured it out in ~30min without introduction. Also the device tells you if the spice is ok, @ rj-45 you mostly have to check the complete cable to find the error.

Almost 100.000 subs :^)

Thank you! It's sad, because especially with regards to professional WiFi 6 APs or newer mainboards, 2.5GBase-T will certainly establish itself as a cheap step in between. What is really missing is an all-round switch that can handle 1G, 2.5G, 5G, 10G over copper AND/OR fiber.

The 10G fiber to copper module usually has higher power consumption than the SFP+ standard 1.5W, probably around ~2.5W. This causes the heat and thermal problem and makes it more than 70C. Unless we have a good "cooling" system in the switch. Did you agree with that?

i like it

Great video, thanks for sharing. I was curious what you are using to the side to switch videos Full Screen to window-in-window and or software you utilize for your videos? Please and thank you.

Can you show wall plates for fiber cat7 cat8

Now those 10gbps SFP+ cards are like 15-25 on ebay... I aggragate to 20Gbps on my servers.

I do not see links to the 10G card

If I have to rewire the house I'd go for the highest available standard, CAT8 or go glasfiber. With the latter being costly but also interference free when new wireless signals might end up trying to interfere with the copper cables again in your house.

Note: Not all PCIe cards with two SFP+ slots can do dual 10Gbit. Some can only do "failover"; eg. 10Gbit on one port and if that fails, you get 10Gbit on the other instead. I prefer fiber everywhere I can, because once you've tried frying a few 8P8C ports (due to high voltage differences between devices), and you no longer can upgrade your Mac OS, you're not going to risk doing that again. (Well, it wasn't only the two ports on the Mac Pro's motherboard that got fried; also my router and my switch - the switch can now do 100Mbit instead of Gbit, so it still "works").

Can not run Cat 6 in same conduit as Electrical So,I want to run 100' Fiber ( OM3 duplex 50/150 OFNP LC-LC ). Reason Fiber is... it will be in with 120v electrical wires in the same conduit from house to my garage. Will this work ??

which small 10g switch it is ??

Im using om4

there are alsow sfp vdsl modems (vdsl modem in sfp form). great for some stuff.

Whats the actual intel nic model though

In an enterprise environment like a data center it’s better to use lc lc cables than dac even sfp+ is better. The optics get really hot in a data center environment and the optics fail. Dac cables if this happens the entire cable needs to be replaced. With lc the optics just needs replacing. I have never had a cable failure before it’s always been the optics or a port failure. It’s a pain because if the dac cable is 20m and the optics fail you have to pull the entire cable out and replace it which in a data center is a time consuming process.

SO the SFP+ cable can also be used to connect to a disk array? OR is it a different type of cable?

The heat issue with the 10g sfp+ modules is really when you have 2 or 4 of them right next to each other and they heat soak each other. Most switches tell you to skip a slot when using them. Would be nice to see what 4 of them next to each other does.

Can the blogger help me amazon review it?

Were was this a few days ago? while I figured out sfp+ trancevers and fiber

Your server room is hotter than the port!? 😂

Has anyone used a HPE sfp+ module on a mikrotik switch? I've a few of them laying around and I'm thinking about buying the css326 24g 2s+ switch for my soho network.

So with this i can hook up with a 10gbit direct connect to Amazon Web Services?

will 1g rj45 receiver in between 10g network card and 10g NAS will only run 1g?

Is LC multimode cable the choice for home users if you want 10Gb fiber connection?

Out of experience: the RJ45 modules always hotter than the fiber ones. I don't really understand it because only in the fiber modules there is a conversion and the amps going through the copper line should be fairly low. It is how it is

Thanks a lot. Help me please. I have cat 6a cable and buy sfp+ rj45.. why only 30m... i have 70 m... what can i do to 10 gbps? Thanks for your videos

Finally someone who knows how to pronounce "MicroTik". =) -To my knowledge, there's no firmware on the SFP / SFP+ modules; there's only a short byte-table of 16 bytes (if I remember correctly).Those tables can easily be duplicated by a manufacturer, but if you purchase one that is 'coded', then it will only work in those products that are compatible with "anything" and those that require this code-table (like CISCO). So a CISCO-compatible module would (likely) not be compatible with HP and vice versa. That said, there are some modules, that contain diagnostic support, which means they'd have a microcontroller built-in, which means ... they would have firmware. Fortunately for us users, the diagnostic support is optional, so we are not restricted by that.

now I just want 10 gb network. Do you have links to all that I would need to start?

any recommended switch hub that has atleast 2 ports of 10G RJ45? All I can find now are all 10G SFP+ switch hub but my LAN & NAS only has 10G RJ45.

Which sfp standard can go 25/40/100Gb?

What makes a 10km SFP a 10km, and a 40km a 40km? What is the difference? Is it power tx power and receive sensitivity?

Good evening I have a question I have a Dream machine Pro from ubiquiti and a 24-port switch The US-24 from ubiquiti what kind of cable do I have to buy to connect these two together I would like to connect these over sfp ? I wonder this because the Dream Machine Pro has 2sfp plus ports and the Switch has two regular sfp ports

I have about 100 feet I want to run a 10 gig back bone from my office out side to my home. Can you get 100 feet of fiber already made up. or will copper be better. Every thing in the office I want all 10 gig back bone. That way every thing will be fast as I can get it with in the home network, for security cameras and the such.

12:14. Cat6e. Well that’s a new one lol.

Anyone have reccomendations for aruba switch compatibility?

why just use LC fiber lach conected direct to red adapter? why use the SFP+? its not more easy conect optic in the red card and the card make the swich from optic to electric signal?

Hi where are the links to the items?

For 30m(~100ft) connection for 10G, do You suggest copper or fiber?

#Designer#sub#Highlights#episode episode Full#awesome

10GTek DAC Cables wouldn't work for me between an Intel and anything

Kanal Türkçe olsaydı süper olurdu

Why SFP or SFP+ connectors are so expensive.? 😰

FYI, the company themselves pronounces the name "my-Krah-tik".

Tom, you make me nervous when you keep leaving fiber connectors uncovered. The dust caps should go on as soon as you disconnect.

Axwell (Swedish House Mafia) secret brother… 😂🤣😂🤣

Devil of a time with the mikrotik CRS3 + the SFP+ to RJ45 module going to my workstation with aquantia onboard nic. I have tried 3 different media converter modules.. no joy. Post in the forums w more details. forums.lawrencesystems.com/t/thinking-about-a-10gb-network-this-might-help/738/20?u=omcn Definitely not plug and play.

I HATE the transceiver release switches!

HI Lawrece System /PC Pickup 👉Cool- Lab-Work 👌😎 Is This Network Card Good For Medium (Between) 2 HP Server For My Project !!🤞 - HP NC523SFP Dual Port 10Gbit.🤞 - HP D380 G8 CPU XEON E5-2670 2.6Ghz 8 cores - To Unifi 10Gb Switch. .... DataMek from 🇩🇰 Denmark.👍🖖

iperf iperf iperf

It's funny to listen how the cat6 is "getting cheaper" in North America: there is hardly any non-cat7 TP sold in Europe.

Did you just gender my switch, bro?!? #ridiculosity

Please keep things *high level*. I want to know your architecture, and how everything works nicely together, I don't really care which plug you use specifically or whether it is silver or blue.

10g is old, get some 400g content.

It's pronounced MY crotech. :( #FAIL

you don't make any sense

very poor explanation ...... i watch you video to gain some knowledge but waste of time