COMPLETE INSTALLATION OF A NEW BRANCH CIRCUIT FOR AN ELECTRIC VEHICLE CHARGER BY AUTEL

Подписаться 25 тыс.

Просмотров 12 тыс.

50% 1

In this video you’ll see how I installed a new electric vehicle 60 amp/ 240 volt branch circuit for a new Auto LEVEL 2 Charger EVSE in Old Bridge, New Jersey.
Autel Home Level 2 EV Charger up to 50Amp, 240V, Indoor/Outdoor Car Charging Station, Wi-Fi and Bluetooth Enabled EVSE, Flexible 25-Foot Cable,Hardwired, Dark Gray.
Electrical Wiring is NOT a hobby. Call a licensed electrician!
Classic Electric, LLC | Point Pleasant, New Jersey
License & Business # 16557
(732)-770-1437
Want to be an electrician? Start here: www.myelectric...
Ron Pecina Jr. is a licensed electrician in the state of New Jersey since 2009.
This allows him to apply for electrical permits, work with live conductors, remove meters, and disconnect service from the utility company.
New Jersey observes the 2020 NEC and the Uniform Construction Code.
The majority of the work you’ll see on my channel falls under the New Jersey Rehabilitation Sub Code (Chapter 6 of the U.C.C.) www.nj.gov/dca...
ALL New Jersey licensed electricians MUST complete 34-hours of continuing education units each tricentennial period.
This includes a mandatory 9-hour code update course and (1) hour business law class.
Any work above 10-volts requires an electrical license in New Jersey.
Ron is an active member of the New Jersey Independent Electrical Contractors Association.
Become an NJ-IEC member here: www.nj-iec.org
IEC National: www.ieci.org
Customer Guide for Electrical Installation; JCPL: www.firstenerg...
Customer Guide for Electrical Installation; PSEG: nj.pseg.com/bu...
WANT TO SEE MORE? FULL 200 AMP SERVICE UPGRADE. WATCH HERE:
Classic Electric, LLC is a Generac standby air-cooled generator installer. Generac Dealer # 1019500
Ron Pecina Jr’s set up:
Camera: Go Pro 9/ 10 w/ the Media Mod
Microphone: DJI Wireless
Editing software: Apple iMovie
Animation software: Apple Keynote
Background Music & Sound Effects by Soundstripe.com
Like, Share, and Subscribe!

Опубликовано:

15 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 131

@matthewgotay1027 9 месяцев назад

Hey Ron, I appreciate your videos to show how hard it can be to install home electrical. As a master electrician, I am putting a notice on this video stating that 6awg Romex is not rated to be installed on a 60amp breaker. The NEC 110.3(B) states, listed or labeled equipment shall be installed and used in accordance with any instructions included in the listing or labeling. This rule is easily overlooked. Per manufacturer rules of all romex you shall install to the ampacity of no more than 60 degrees. This means 55 amps max on 6awg romex. No exceptions. Please correct future installs and remember electricians are obligated to install to the minimum guidelines on the code book regardless of what your jurisdiction says , you cannot go beneath it. Feel free to use 4awg aluminum SEU or 6awg copper SEU or use conduit 6awg thwn.

@electricianron_New_Jersey 9 месяцев назад

Go read the DCA on the 55 amps and lmk.

@electricianron_New_Jersey 9 месяцев назад

6/2 NM is good for 55 amperes. Read about NJ's decision to allow the use of 6/2 NM here: www.nj.gov/dca/divisions/codes/publications/pdf_ccc/CCC_Fall_2023.pdf

@donmclean1220 8 месяцев назад

Does anyone know if this allowance has been made in other states? Installing EV chargers is going to be more and more common. Great video, Ron.

@electricianron_New_Jersey 8 месяцев назад

It does contradict the language in NEC Article 210.19(A)(1) so best to check with your states requirements. @@donmclean1220

@Californians_go_home 8 месяцев назад

Ryan Jackson just posted a video about this specifically on his RU-vid page. I suggest everyone check it out. 4awg must be used no question. This is not a promo. Ron I suggest you see what he has to say. You have to go by the 60 degree table with nm cable.

@johnmazzocchi7116 9 месяцев назад

Hey Ron! Just purchased 6/3 Romex at HD! I nearly had a heart attack! Nice job as always. Be safe brother

@electricianron_New_Jersey 9 месяцев назад

Right? Try selling it and installing it. It’s not cheap!

@ronaldnaeyaert3653 6 месяцев назад

Recommend checking local electrical supply houses before buying wire at the big box stores. I needed 50' of red #6 THHN. $1.59/ft at the big orange store, $.71/ft at a large national chain of supply houses with 600+ branches

@ElectroAtletico 9 месяцев назад

1st!! Diggin' that "DeWaukita" hoodie.

@electricianron_New_Jersey 9 месяцев назад

The Dewaukita hoodies can be found @FinishcarpentryTV channel.

@RBB73 9 месяцев назад

Love the DeWaukita Hoodie ! - Thanks for the video.

@mattschoular8844 9 месяцев назад

Nice Job Ron. Keep up the great work. I love the fact that "Struggles are real".

@electricianron_New_Jersey 9 месяцев назад

Thanks 👍

@pcotangco 9 месяцев назад

Thank You and you have exceeded my expectations. I recommended your business to my community page. Hope to see you around. Thank Again

@electricianron_New_Jersey 9 месяцев назад

Thanks Paul!

@franklong6269 4 месяца назад

Great Video! That 6/.2 is really hard to work with. I just installed a Tesla Universal Wall Connector at my home, and just bending and cutting the 6/2 was a pain in the ass. I was also surprised by how much the 6/2 cable cost. I would make one recommendation to help you. Buy a 12-volt Milwaukee impact driver instead of a hammer drill. It is light, and believe it or not, it has over 100 ft-lbs of driving force. It will help you drive your screws into wood much easier, and you can use it to tighten electrical screws (snug them up) and loosen frozen screws. It's small and easy to carry and it is much better than a drill. For example, installing the Torx screws in this charger would have gone MUCH quicker using the 12V Milwaukee impact driver. It won't over-drive the screws and strip them out if you are careful because it has a variable speed trigger. If you learn to use a small impact driver instead of a screwdriver and drill, it will save you a lot of time. With really delicate screws, you will still need to use a screwdriver, but you will find that you can use this small impact driver to drive 3" wood screws as well as a wide assortment of other screws.

@milosrestoration1337 8 месяцев назад

I like your videos so much. Just showing what you do day to day. Also the fact that there’s no complicated legalese to it. Service entry work on my own has been intimidating to me as starting out maintenance electrician and seeing you do it has been great to help me get a work flow together. Thank you.

@electricianron_New_Jersey 8 месяцев назад

It’s flattering to get comments like this. It makes me happy to know people learn from watching my videos. It’s a great feeling and I thank you.

@j19090 8 месяцев назад

Love the sand bur stuck on the back of your cap. We have them in Cape May too.

@iEliseoForPresident 6 месяцев назад

Love throwing on your videos while I do dishes and meal prep lunches for the week

@gregmiller-breetz3368 6 месяцев назад

When you were landing the Romex in the panel I kept looking for the grounding conductor but never saw it. From then on I was so distracted, kept wondering what kind of exception would allow you to skip running one. And then I saw it at the charger. Stupid comment, I know. Great work, as usual.

@titanelectric360 6 месяцев назад

Good educational video. Wish I had the skill and patience to record and edit all our work. For now I'll just keep telling my guys to watch your channel.

@electricianron_New_Jersey 6 месяцев назад

Thank you. Yes, it takes a lot of time and effort to make decent videos. I love teaching so I’m going to keep doing them.

@johnwalker890 9 месяцев назад

Good job Ron, I always go extra on the wire, better too long than too short.

@electricianron_New_Jersey 9 месяцев назад

Right on

@fathertomahawk 9 месяцев назад

A little scrap never hurt no one. Repulling cuz someone shorted the wire footage hurts tho.

@CryptoTikibro 8 месяцев назад

Great work Ron. I just bought a fixer-upper with old mc with no ground, the previous owner had a nice modern 150 Amp service panel installed. But all the wiring is ancient. How should I look for shared neutrals? I'm now replacing receptacles. (until I'm able to start rewiring).

@electricianron_New_Jersey 8 месяцев назад

Open up the panel cover and look for any 3-wire branch circuits. You may, or may not have them.

@CryptoTikibro 8 месяцев назад

Thanks good buddy

@alphasaiyan5760 8 месяцев назад

I do a lot of these ev charger installations. I’ve put #8 on a 60 amp breaker using a 14/50 receptacle before and havent had any problems out of it. It’s used daily. It was a hurry up rushed job and all I had on the truck was some #8 Romex and a qo260 breaker. Most of the time,99%, I use #6 either Romex or THHN. That time I used the #8 it was a run of like 10ft from the panel to the outlet. I also didn’t use gfci protection oh 😱

@electricianron_New_Jersey 8 месяцев назад

So next time you do better right?

@alphasaiyan5760 8 месяцев назад

@@electricianron_New_Jersey yes sir. I haven’t done that again and I never will 👍🏼

@solomonperillo5765 6 месяцев назад

Hey Ron nice work what brand work pants are you wearing

@thomaskenney 9 месяцев назад

Are there any requirements for a GFCI breaker for an EVSE? Thanks. Great video!!

@electricianron_New_Jersey 9 месяцев назад

Only if you’re using a receptacle like the 14-50.

@thomaskenney 9 месяцев назад

Thank you!

@vince6829 6 месяцев назад

Nice job, as always. Thanks for sharing your knowledge.

@anthonyelectric6045 9 месяцев назад

Love those Greenlee sandwich warmer 👍 nice job

@josephknapick5307 9 месяцев назад

Hi Ron... Another great video. Question 1: At 7:31, you post 625.41 which requires overcurrent protection with a rating of not less than 125 percent of the max load of the equipment. At 9:31, it appears that you install a 60 amp bkr for this 50 amp load. It that acceptable? Question 2: Is 55 amp rated 6-2 romex (as opposed to #6 THHN) acceptable for this 50 amp continuous load?

@electricianron_New_Jersey 9 месяцев назад

NM 6/2 is only rated for 55 amps but the Division of Consumer Affairs has approved this wiring method for EV Chargers.

@chuckq54 9 месяцев назад

That unit is definitely a pain with all the Torx screws…excellent work as always Ron 👍👍

@electricianron_New_Jersey 9 месяцев назад

Thanks 👍

@Trainman0401 7 месяцев назад

Going Crazy! 😵‍💫 Maybe you can help. When connecting a disconnect box on a vinyl siding home, can I use a standard Romex connector on the back of the box and connect 12/2 to it. I will use duct seal clay to fill any voids behind the box. I can’t find any info on this online. Love your videos! Thank you Ron!

@electricianron_New_Jersey 7 месяцев назад

Yes, absolutely

@Trainman0401 7 месяцев назад

@@electricianron_New_Jersey Thank you so much for your help over the years. It is greatly appreciated.

@DanT271 9 месяцев назад

Very nice job Ron I have a lot of electrical knowledge but am not an electrician but the main breaker goes off before I remove the panel cover and does not go back on until the cover is secure don't need any nasty surprises

@electricianron_New_Jersey 9 месяцев назад

Yeah that’s definitely safer.

@jimanderson4495 9 месяцев назад

How long start to finish did this take? Thanks Ron. Stay warm this winter on those outside jobs.

@electricianron_New_Jersey 9 месяцев назад

Start to finish including picking up materials, looking at the work before being hired, and the permit process, about (8) hours total.

@garycunningham8478 8 месяцев назад

What’s the code for putting romex through pvc?

@zekenzy6486 9 месяцев назад

Great Video. Nice Job. Thank you for sharing

@gg-xu1zv 8 месяцев назад

Great video Ron! When mounting the charger on vinyl siding do I need to find a stud to secure the bracket screws into or the plywood beneath the siding is good enough? Also, do you recommend applying silicone around the charger?

@davidchilds9485 6 месяцев назад

Hey Ron. I am enjoying the video. One question. Does the NEC prohibit install type nm cable in conduit. Also is #6 nm (60 degree C Insulation) approved for 60 amps? Thanks

@electricianron_New_Jersey 6 месяцев назад

It is in New Jersey but not by the NEC.

@GlenMacNeil 9 месяцев назад

Great video Ron. The struggles are definitely real. I'm getting ready to get into EV installs and I was curious to know what to charge for an install like this? Thanks Ron.

@electricianron_New_Jersey 9 месяцев назад

Anywhere from $900-$2500 depending on where panel is and where the charger is going.

@GlenMacNeil 9 месяцев назад

@@electricianron_New_Jersey Thanks Ron. Really enjoying the videos.

@norsk54472 9 месяцев назад

nice and sweet, thanks

@jefferykerr09 Месяц назад

Hi Ron, do you remember the size of conduit used to hook up to the charger? Thanks

@electricianron_New_Jersey Месяц назад

3/4" PVC

@mosheish 9 месяцев назад

Hi From ISRAEL love the swetshirt ...

@2684ART 9 месяцев назад

Ron, greetings from Ukraine. My question is: Do you torque the connections with a torque tool to check and how stringent are your requirements for this? Thank you.

@electricianron_New_Jersey 9 месяцев назад

Most EI’s don’t check for torque anything, especially old timers.

@2684ART 9 месяцев назад

@@electricianron_New_Jersey Thanks for the answer))

@2684ART 9 месяцев назад

@@cengebLottery.)))

@benthomas3418 9 месяцев назад

nice work Ron as usual! i like the sweater!

@electricianron_New_Jersey 9 месяцев назад

Thanks!

@garycunningham8478 6 месяцев назад

You’re in my town today

@garycunningham8478 6 месяцев назад

I would have helped you

@salvadorcastillo1539 9 месяцев назад

Thank you for your videos....

@alexm8187 8 месяцев назад

Hey Ron, I just stumbled upon your channel today an subscribed right away! The more I watched your videos the more I felt a connection.. Your an electrician by trade that also has a passion for woodwork an tools. love your sweater #finishcarpentryTV! Really looking forward to watching your future content, So keep up the great work and Thanks for your knowledge!

@electricianron_New_Jersey 8 месяцев назад

Thanks man. Thanks for subscribing too!

@imthatguypal9999 8 месяцев назад

Hey Ron, I am a very new residential electrical contractor in Washington. Right now I am solo like yourself and was wondering what your opinion is on becoming a certified installer of particular brands of equipment. For example, you can become an Eaton Certified Installer for about $500. I would like to hear your thoughts on this- is it worth it? Thanks buddy!

@herbpantaleon7485 9 месяцев назад

Nice job Ron!

@Frank-Lobos 9 месяцев назад

Great work, Ron. What headlamp are you using?

@electricianron_New_Jersey 9 месяцев назад

600 Lumen by Milwaukee.

@GB-mw7eh 9 месяцев назад

Great work as usual Ron!

@electricianron_New_Jersey 9 месяцев назад

Thank you! Cheers!

@dadtothebone4859 8 месяцев назад

Hey Ron I’ve been going threw all your vids can’t get enough. Quick question whenever your doing drilling with the m12 is that still with the impact or do you use the m12 drill

@electricianron_New_Jersey 8 месяцев назад

I usually use M18 for drilling holes. I’m slowly moving away from using the impact and choosing the M12 drill/ driver for driving screws and such.

@TKomoski 9 месяцев назад

Ron if there is a code violation does the inspector inform the homeowner or just you?

@electricianron_New_Jersey 9 месяцев назад

This person would just leave a sticker. They’re supposed to leave an NEC section for reference but that’s not always the case.

@jjzapari8063 9 месяцев назад

What was the total cost for the homeowner for this type of work

@Simonelectricfl 8 месяцев назад

Great video

@jefffielder2429 9 месяцев назад

Nice pvc bending and yes those chargers are a pain to open

@electricianron_New_Jersey 9 месяцев назад

Tell me about it!

@paulcarlsen4088 9 месяцев назад

Sweet Hoodie!

@Bob.W. 9 месяцев назад

Thanks.

@electricianron_New_Jersey 9 месяцев назад

Eh, not unusual.

@Bob.W. 9 месяцев назад

@@electricianron_New_Jersey true.

@jeremiahnewsom7775 9 месяцев назад

Hey Ron is 6/3 romex good for 55amps 60degree? I know the terminals are only good for 6awg. That hoodie is badass!!!!!!

@YaksAttack 9 месяцев назад

Per 2020 NEC, #6 Romex is good for 55 amps.

@electricianron_New_Jersey 9 месяцев назад

Per the NJ DCA 6/2 is good for 55 amps and acceptable.

@jeremiahnewsom7775 9 месяцев назад

@@electricianron_New_Jersey I guy I work with said he failed before using romex. I never really thought about it until he brought it up. Most the hardwired ones Iev done were piped. The terminal in charger only go to #6 so they splice box in garage to #6 thhn. I think it is better to not have splice or aluminum so I was wondering if you had encountered any problems with it! Sounds like your state is on the same page about!

@ajrichardson80 9 месяцев назад

@@electricianron_New_Jersey what is the size of the bottom knockout for that unit? I have one arriving on Saturday and I want to have all of my supplies ready to go when it arrives.

@YaksAttack 9 месяцев назад

@@jeremiahnewsom7775 I used to wire all 48 amp EV chargers with 6/2 NM until inspectors started failing my installs, which never made sense because the conductors in the NM have 90 degree rated insulation and should handle the load fine. Switched to pipe and 6/2 MC, and haven't switched back to NM yet because I don't want a super trooper inspector to fail me and make me redo the entire install.

@Jimmy_Boy 9 месяцев назад

I'd like to understand how you determine if the electrical service has the capacity to add a 60 amp continuous load EVSE.

@electricianron_New_Jersey 9 месяцев назад

I do a load calculation if the BLDG DEPT requires one. Would you like a video about that?

@kevinelie9612 8 месяцев назад

Yes@@electricianron_New_Jersey

@michaelcollins5438 8 месяцев назад

That would be a very interesting video

@evanrocha5465 7 месяцев назад

Load CALC would be great! Curious to how one is done correctly

@thomascannan1033 9 месяцев назад

I like your sweatshirt I have one too from another youtuber!

@charlesanderson6226 8 месяцев назад

Love the hoodie!

@electricianron_New_Jersey 8 месяцев назад

RU-vidr sells them on his page: @Finish Carpentry TV

@ClippyC 8 месяцев назад

lol - how about a red sharpie? I'm being sarcastic.

@billmonroe8826 9 месяцев назад

I love it when people buy an EV and then spend more to be able to charge it while creating jobs. In seven to ten years the battery will go where? Nice work Ron!

@electricianron_New_Jersey 9 месяцев назад

As long as my vote is counted.

@billmonroe8826 8 месяцев назад

@@electricianron_New_Jersey Oh, it probably will be counted at least ten times. lol

@jimchapp254 5 месяцев назад

no sub panel for 60 amps ?

@electricianron_New_Jersey 5 месяцев назад

Why?

@jimchapp254 4 месяца назад

NEC 2017 60 amps or more needs a shut off sub panel

@electricianron_New_Jersey 4 месяца назад

@@jimchapp254 I've done more EV chargers than I care too remember. The disconnect is only required for over 60 amps. Most are only 40-60 amps even with the 125% as required by NEC 625.

@jimchapp254 4 месяца назад

@@electricianron_New_Jersey thanks , for clearing that up for me

@jefffielder2429 9 месяцев назад

Do buddy tail your tape ?

@electricianron_New_Jersey 9 месяцев назад

Wtf are u asking me?

@jefffielder2429 9 месяцев назад

do you leave a twisted end on your tape when you have to remove the tape @@electricianron_New_Jersey

@electricianron_New_Jersey 9 месяцев назад

@@jefffielder2429 yes! I call it “the Dolan” because the person who showed me was taught by an electrician named Tim Dolan. True story.

@alphasaiyan5760 8 месяцев назад

I call it a “ courtesy tab” 👍🏼