Des explications claires et précises pour souvent des problèmes potentiels !!!!Merci pour ce tuto où j'ai trouvé ce que je n'avais pas de façon simple et compréhensible. 👍👍👍👍
Merci! Cela a complètement clarifié la question de l’utilisation d’un pilote externe pour moi. (Thank you! This clarified the issue of using external driver for me completely.)
Thanks Topsie! I am planning a modification to the z-axis of my MPCNC and it is obvious that the Nema17 with A4988 on a CNC-Shield, is overloaded. This video was just very helpful to me and special thanks for the English subtitles.
nema 17 serie motors not torgue and power use cnc, neam 17 used only laser or 3d printers not need lot torgue. if build small wood carving cnc minimum need nema 23 or 34 motors, torgue need be more than 2Nm/cm normal used nema 23 3Nm motor this is totally minimum can move and cutting wood. u can use small motors but stupid because lost step if not torgue can move spindle and lot fail parts come. or cutting super small chips out of wood only and waste lot lot time and normal strong motor can cut biggest chip out of wood, this mean bic motor cnc cut wood one time and about 1 minute, and small motor cutting wood many many time and 1-2 hour, same work.
Super vidéo, des explications claires. De mon coté j'utilise des Nema 34 qui consomment 5.8 A/phases. Le problème est que le shield CNC que tu nous présente ne peut délivrer au max de 2A/phases. Je suis un peu bloqué du coup x)
@@createforcuriosity225 bonjour, comme je l'ai dit sur ton forum, je vais donc attendre pour connaitre tout ce qu'il faut pour cette version 32 bits lol (Malcom 38)
Just wanted to say great video. I guess where i become confused is which outlets on the Microstepper are ground. PUL(+5V), PUL-, DIR(+5V),DIR-. And would i also have to connect the 36V powersupply to the CNC V3 sheild? Thanks!
Hi! Thanks for the video. Do the 3 connectors under the capacitor, where a small stepper would be placed, need to be connected like on your board in order to use the external stepper controller?
Merci pour la vidéo, les explications sont intéressantes, serait il possible d'avoir un petit schéma du câblage de cette configuration ? Je suis en train de terminer ma cnc et j'ai des doutes sur le câblage à effectuer sachant que j'ai les mêmes composants que ceux présentés sur la vidéo (cnc shield, nema 23- 1 pour le x et 2 pour le y-et un nema 17 pour le z, et les contrôleurs moteurs) 😁
@@createforcuriosity225 Ça serait effectivement bon d'avoir ça car je suis suis pas sûr d'avoir suivi le shéma qui vient avec les DM556y, mais mes moteurs sont renversés en direction. Ça serait bien de nous clarifier là-dessus si tu pouvais. Merci!
Bonjour bonjour, merci encore pour cette excellente vidéo: je viens d'installer bcnc et j'essaye de trouver des tutos pour son utilisation: dis-moi, puisque j'utilise 100% fusion 360, avec ses chemins d'outils, ect.., quand j'ouvre le gcode d'un de mes fichiers dans bcnc, aprés avoir renseigner les config, fait un home, est-ce je peux lancer le job? ou bien parametrer tous les boutons/fonctions de bcnc? Ou autrement dit, est-ce que je peux me servir de bcnc comme un "lecteur de gcode"? A++
For kicks, I just started a project using an Arduino CNC shield connected to DM556Ys. Quite a different world than a “regular” CNC control board. Thanks for a great explanation. While I’m at it, how do these DMxxxY fare compared to their DMxxxT cousins? I always had good results with the “T”s but went with “Y”s for this small project.
Salut super vidéo . Dit moi quelle est et la taille de travail de ta fraiseuse ? Ou à tu trouver les tige filetée au pas de 2mm je suppose ? C pour modifier celle que j'ai avec courroie. Merci
super video! je suis en train de confectionner la même. 3NEMA 23 en XYA et 1 NEMA 17 en Z petites questions: - où faut il mettre des cavaliers? Je vois un cavalier sur EN/GND à côté des Dir et Step - je n'ai que 2 sortie 5V de la CNC shield: ya t il un 3eme port?
J’ai une question en rapport avec ta présentation 🤔 il existe plusieurs type de Nema 23, je comptais utiliser des 23HS7628 avec un couple de maintien de 189 N.cm. Quel est la limite d’utilisation des shield ? Est ce qu’il est nécessaire d’utiliser un driver externe pour ce genre de moteur ou est ce que les shield sont suffisant ?
Hi, What's the max mm/minute this machine is achieving! I am using nema 23, HT- 3400mNm DT- 100mNm, rated current - 3amp, voltage - 8.4 with TB6600 24V 15amp Power supply is used for all motors. Max I able to achieve is 1800mm/minute
better use motor power TB6600 maximum volt, 40V or near this, 36volt. and power need current 3 motor 3x motor current 3Amp/motor need minimumm 10Amp power supply, i use DM860 motor drivers and nema 34 motors lot better use, 5A /motors max and 48 volt driver motors power volt. arduino shield V3 need only own power and 5V out step and dir. thats all. but lot lot lot better cnc can make linuxcnc to pc, realtime controll and flexiple make own makros,hal files, tools, etc, and paraller port car to pc and paraller port controller, same than arduino but paraller port, and then same external drivers etc, DM860, and better big motors nema 34 12Nm 7A have good.
Bonsoir , J'ai un problème avec mon nema23 , lorsque je le fais tourner avec cncjs, il fait des aller retour. Ma config est nema23 CNC Shield tb6600. Est ce que quelqu'un pourrait m'aider ?
Pourquoi tout le monde s'emmerde à brancher les TB6600 sur le CNC shield? Autant les relier directement sur l'arduino? Je vois même pas le gain en facilité.
if external driver handle max 50 volt then better use max what u can make power supply to motors, maybe best use power supply 46Volt, near maximum external driver, and current need be setting dip switch near maximum motor max current about 4-or 5 Ampere normal.