Creality Ender 3 V3 SE Failed Print Issue Fix 

many thanks for taking the time and explaining what's needed to keep your printer functioning. I found a couple of the screws on my rails loose after your video and also because i had 2 failed prints around the 80% mark. But had to reinstall firmware in both cases to restart my printer. Look forward to your next video.

This is exactly the problem I’m having and my printer is only 3 weeks old and has done less than a dozen prints.

Thanks for doing this, I just bought one today and I now knowc what to check and maintain

Thank you! This fixed the issues I got with my printer!

Blue Loktite is your friend.The orange type is semi permanent works even better. After i have done that i have put months of print time with no issue. Lots of vibration when printing.

great vid mate, this might be what I've been experiencing, I'll be checking before next print, cheers

well done. good and helpful info.thank you.

What you say is totally correct. When I received this printer, it did everything pretty well, but I felt like I could do better. I adjusted everything and after several months, I feel that everything is perfect. For a cheap printer, it does everything very well and I am very happy. Thank you!

I have just bought the same printer, first print was great but now the print does not extrude material, o believe the motor is failing but how can i confirm it is?

gracias por la dedicacion del video, saludos

Thank you. Value received

One problem I've been having is my ender 3 v3 se will not print hollow objects. I make the adjustments in creality before I print and it prints whole instead of hollow would you have any suggestions on how I could fix this issue

The best upgrade I've made for my pair of E3V3SE printers is ordering some smooth PEI sheets, flip the bed plate overs to mount them on, and reset the z offset. I was having so much trouble with prints either not sticking or not coming off. Plus I prefer the smooth surface when I need to print something upside down. There was one box I printed where the first try wouldn't stick to the print bed so I reran the z offset and the bed level again. On the second try the bottom layer ripped off the part and stayed with the bed. Now if I have first layer issues I can wipe it down with isopropyl alcohol that takes care of it the majority of the time. Both of my printers have had failed BL Touch modules. The first was delivered with a bad one so I just ordered a new printer and intended to return the first but Creality sent me a new module instead. The second went bad within three months and I wasn't going to wait for the warranty replacement so I got one from Amazon overnight. Only other issue I've experienced is one of the fans in the print head started getting noisy. The replacement on Amazon has both fans so I replaced both. I had a pretty severe clogging issue on this one that was likely caused by not cooling correctly. I run both of them off a Sonic Pad which has created it's own issues, such as trying to go through bed leveling before restarting a failed print, but still works fairly well and is much easier than the little screens. If I had to do it again I would likely just go with Octoprint.

printing non-stop using this printer for more than a year at this point, had a lot of problems at the start, as this is my first 3d printer, and I had to figure out a lot of the details the biggest problem I found was wobbly arc, so moving the filament roll to a dryer, and adding a filament guide helped a lot also changed the plastic spacers under the bed for the silicon ones like on the original ender 3, then leveled the bed manually also I changed firmware to klipper for remote management and better bed mesh probing (needs separate host controller)

Can this printer print ABS/Nylon filament?

Thank you!

I just took the silicone off that's over the nozzle and it works fine now

Hope that will solve my problème

Can anyone help with belt slippage on these? I will try all these tips but slippage seems to be the culprit but I have no clue how to fix it on this model

I wonder if there is a consumer hex torque wrench set that has low enough pressure settings for the requirements of this printer, and if the factory can provide the torque specifications. That would make all of this a no-brainer. Maybe we as the community can create that as well.

Jerad, could you please address the horrible stringing Ender 3 V3 SE has? I've tried everything from temperature, to retraction speed / distance to all the tricks and tunes I could find online, but still stringing (also dried my PLA). I'm getting mad!

Do you think that the SE or KE is a better starter 3d printer? I’m looking at both. Thanks for the video - I’m sure it will serve me well down the road!

mine stop after a week - display did not show any text anymore and would not take a filiament anymore, started printing without filement return i to de seller awaiting there feedback

What slicer are you using? I don’t like the creality slicer but the prucia and cura slicers don’t have profiles for the gender 3 v3 se?

There's nothing more disheartening than a perfect first layer, then coming back in an hour(or in my case 2.5 hours) to see spaghetti all over the plate. Argh! Started a print 10 times, making little adjustments between each print, before I gave up on it!

❤Spool at the top might add wobble

Thanks for the video, gave it all a good thigh

step one.. swap the crappy build plate for PEI and save it for TPU prints

solution: the the card around -_-

Get to the point!