D.I.Y Custom Tinny Build COMPLETED! - Part 2 of 2! 

Great jerb. About due to replace my plywood/carpet floor of my tinny. So, I'll be interested to see how your alli/carpet holds up.

Why do you silicon the rivets?

Mate I boat build for a living and i tell you that this is pretty damn impressive. I dont know how much all that aluminium cost you but its great to see you took your time. Well done mate.

I’ve done a lot of boat mods over the years…currently in the process of rethinking my whole set up. I really like what you’re doing, and without welding…😎👍

Pretty damn cool. I’ve watched heaps of tinny fit out vids, but this one is by far the coolest. Gives me some ideas for my tinny. Cheers

Hey mate, thanks for sharing your build process. How’d you go about getting every bit of aluminium shavings out after drilling the holes for rivets? 😂 good to see you using tefgel between your (i assume stainless) rivets and the floor.

You've done the best build 9n U toob bud well done inspirational and proffessional

Very impressive aluminum work! What is the thickness of the aluminum deck?

After a few hours of repairing holes in a new cheapy tinny. Im.glad to see you use tef gel and sikaflex. The idiot b4 me put screws and rivets in holes. All that did was cause more corrosion.

Hi Jamie, Thanks for the videos your posting. 3mm plate for the deck. What thickness did you use for the supporting angle/T pieces/ U sections? Also 3mm? Regards

Really enjoyed this build.

Hey mate thickness plate did u use

Mate bloody epic build and great content I’m about to do a build for my little cutter deluxe and you’ve given me so much ideas legend !! New sub from Hervey Bay :D

Still think it would be worth it to fit a rectifier to motor and run it to the battery to charge it .... really inexpensive to do yourself...the spare wires to do it will be there as part of the loom...👍

What a ripping job. Have been searching for a no weld option and now you have shown me how. Thanks heaps for sharing.

Great boat Great misses Great dedication and planning Great workmanship Just loved watching this, inspirational, educational video mate, been ta Bunnings, apparently the young staff are unable to provide me with a ruler or tape capable of measuring a B's dik or a Nat's nakka, guess I'll have to guess.

Well done mate Yes you need to insulate stainless and aluminium as long the cloth tape doesn’t hold water you’ll be right

Nice job on tinny....gives me a few ideas when i start mine shortly cheers Paul from Melbourne

Bloke.. corepit.

Do you have any fuel gauge or how do you keep an eye on it being under the deck?

What knife holder is that? and where did you get it? thanks!

nice work, what did the fit out end up costing you ? and is that an english accent you keep slipping into ?

Makes you wonder how far behind the manufacturers are in fitting out boats.

Should of painted the hinges black or grey

Hey mate, you got a rough idea of how many meters of ally you used for the framing

Fuckin beaut! Good stuff mate.

Great work Jamie! Hope you fill that esky with some good fish 😎 🎣

Bloody awesome job guys. Looks the goods! 👍🏼

L I K E 👍 👍 👍 👍👍 🌟 ⭐ 🌟 ⭐ 🌟 🤩❣🤩❣🤩🤩

Great job - result well worth the time and patience.

Nice boat setup mate time to Get Some

That's a great build mate 👍🏼

Cool build. One suggestion: instead of the foam and then screwing the floor down you could use 3M VHB double sided tape. Super strong. I've used it for offroad trailer floors and it sticks like nothing else. No need for fasteners and it would do the same job as the foam as well. You only get one chance when gluing the sheet down though.

Great job bro !!What are the brackets holding the two seats ?? I need a couple

Pretty mean build there bro! I'm just about about to do something similar to my new to me rig 😅 . I've got 2 questions for you, 1, what were you putting on the rivets? And 2 how have you found fuel vapour/smell with the tanks under the floor?

Great job. Solid work🙌🏼

Greetings from the US. Nice job on the build. Here we have the Tiny Boat Nation (check him out on RU-vid). What boat is that (manufacturer and size)? Is it going to be a car topper?

Great job mate. She’s a beauty!

Well done great work.

Well done looks great very neat also. How have you found the riverts instead of welding any problems with them pulling or breaking. What are the latches you also used for the lids are they lockable

Awesome build mate thanks for sharing! Do you recall the brand of the storage box in the seat, it looks great.

Bloody good job Bunge

Job well done 👍🏻

Looks great

dude sick! need a follow up on how it goes for a weekend away

Absolutely beautiful my friend great work

Do the spacer in the carbie mate will be a 30hp then 👍

Good work

Great job mate. Looks mint 👌

Well done. What part of the world was shown in the water tests..Airlie Beach or Hinchinbrook?

Beautiful job = beautiful boat !!! Way to go...