Dewalt Atomic Freak? 

I hope this makes an appearance on the Torque Test Channel!

Love the looks and it seems pretty cool but just for videos and stuff I believe if people start doing that to the 850’s they are going to put the tool through some stress tests that are going to end up in smoke.

Love the Hart hand tools. They actually make some decent stuff for the price.

I swapped out many 877 impact drivers to 3/8. I also did the 845, but my new favorite is the dcf 860 I swapped it to 3/8 drive it makes a lot more power than the other models

I think I'll try adding one of these to my DCF 840. I use it as a truck impact for tore changes.

Small recommendation for future: have the inset face-camera on the top right so it doesn't cut out any of the work.

I converted my Bauer impact drivers like this for specialty uses i needed to run ultra deep 9/16 sockets for fence panel clamps but they were half inch drive and snapped hex adapters regularly so i put a similar anvil into several and they hold up to my uses

Dewalts collate is sweet I like that Dave @Man Caver Tools

This is badass! Keep it up!

The new Ryobi Hp rotory tool is bad ass it has a Ratcheting Chuck for faster changes been loving the new one I also have that rotory tool it's good @Man Caver Tools

This is some great content. Well done.

Bro excellent video. You helped me make what I think is the strongest 1/4" drive impact wrench. One thing I did notice is that it is much louder than most the other tools after you do this mod. Even than the standard 1/2" impact wrench. Did you notice this? It makes a more high pitches screeching noise.

Nice that the tri light is easy to remove from the dewalt compared to the Milwaukee didn't come off @Man Caver Tools

No Brasil temos somente a linha de parafusadeiras bosch com esse drive de encaixe para ambos 1/2 e 1/4 no mesmo equipamento que vejo sendo vendido nas lojas.

Nice work 👍

I mean, I'm glad it's such a powerful little monster, since I got one in a combo pack a bit ago, but at this point I'd just use the DCF921, personally

I wonder how long it’s gonna take for dewalt to start selling them like that

DeWalt Freak vs Milwaukee Frankenstein vs Atomic DCF921, pleeeeassee

Birth of the fReAK! Link to the Anvils please :P

love this!! - i was just about to ask WHERE YOU GOT IT, then i watched the rest of the video :D

VERY COOL ,,,,,,,,,,!!!!!!!!!!!!!

This is just AWESOME! Coould you do a Metabo HPT 36V Triple Hammer Impact Driver??

Freaking Slick bro @Man Caver Tools

i used the WORX anvil WU279 on my atomic dcf809 it is straight swap no modification

Yeah buddy! 👍

Amazing! Very very strange choose. Why not DCF 922 ?? it is twice better then DCF850, because the 400Nm vs 200Nm. And maybe the 17.8 mm from the manufacture. Also the same weight almost.

Cool video. Question.. will you ever try and get your hands on CAT cordless tools and see what they are all about? Haven’t seen much on them but supposed to be good quality. Just a thought. Keep on rockin the vids 👍

Just wow 😮

Hey, hope you see comments on old vids...the link to the part isn't in the description anymore, do you have a part number I could look up?

Pretty cool but how many impact wrenches do u need lol

You don't need to dremel anything, but it does take some finesse. An awl (like one that comes with a leatherman for piercing leather) and a screwdriver will allow you to pop both of them off. Just don't do what I did and stab your finger deep. Still bleeding as a write this.

Sick!!

you should have 1/2" to 1/4" adapter

What are the measurements of this 1/2 adapter? Do you have any Aliexpress link?

Im having problems with my swap on my dcf850. My anvil is flippity floppity in the housing and cannot figure out why i didnt see you use a snap ring on the anvil or anything

Curious, the bosch had the red collet ring to pull to lock the 1/4" bits in. How do you do that with that anvil?

Y vídeo de prueba ?

Nice! 🍺🎸🤘

Can you do a vs demo with it like you did with the M18 Frankenstein vs the M18 Stubby video?

I want one!!

Hi got a dewalt question. You guys in the US got news about the new powerstack 5ah yet? We in Scandinavia has got some commercial about that yesterday on youtube. Seems legit. You can search for "POWERSTACK 5.0AH BATTERI NEXT DIMENSION IN POWER"

What size torque socket to open the body? Thanks

Could you change that on m12/ m18 surge

Would this fit directly into a 1/2 m12 stubby??

Is it possible to put a 3/8 anvil on a gen 2 m12 fuel impact driver 2553-20

So how does it release the bits without a collet ring?

Would this work on the dcf887?

What kind of anvil is that,?

Anyone know if this will fit the DFC801 ?

Don't care for the picture in picture. It is a distraction. Your videos are better without it.

Man, tools and working with them, it's not yours.. I almost fell off my chair from the clamps..

Your Onlyfans is 🔥🔥🔥

I hope the warranty is expired because you just negated it.