No video :(

DIY 2013 2014 2015 2016 2017 Honda Accord Replacing Rear Brake Pads

Подписаться 6 тыс.

Просмотров 40 тыс.

50% 1

Watch how to replace rear brake pads on a 2013 2014 2015 2016 2017 Honda Accord. #honda #hondaaccord
Parts & Tools Used:
Rear Brake Pads - amzn.to/44ctbFC
Disc Brake Caliper Compressor Wind Back Tool - amzn.to/44yoaqE
12mm Socket - amzn.to/4bn25i8
3/8 Socket Wrench - amzn.to/4bONMTn
Brake Part Cleaner - amzn.to/4dF17iC
Brake Grease - amzn.to/4bN376F
Adjustable Wrench - amzn.to/3WPlWSK
Jack - amzn.to/3QUtgZr
Jack Stands - amzn.to/3wLl5rt

Опубликовано:

19 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 56

@npolite22 Год назад

One thing that is missed here is that the cross pattern on the caliper has to match the pin on the rear plate of the brake pad. If it does not line up it will create excess pressure and wear the pad in no time. I like you must have been lucky a half a dozen times before I hit this issue

@MobileCarMechanic Год назад

I have not been that lucky but I went back and ensured the cross pattern on the caliper matched the pin on the plate. Thank you for the feedback.

@fishifritz 9 месяцев назад

Before mounting the wheel back up, pump up the brake pedal. then use the parking brake to keep the wheel from spinning when you tighten up the lug nuts.

@MobileCarMechanic 9 месяцев назад

Very good tip! Cheers!

@thardyryll 9 месяцев назад

Or merely pre-torque the lug nuts with the impact wrench and lower the vehicle to the ground for final tightening...

@Striker50_ 11 месяцев назад

Another great vid 👍 I did 2 vids on this with pads and rotors for both front and rears since I was getting a clown horn noise when braking

@MobileCarMechanic 11 месяцев назад

Greatly appreciated! Cheers!

@jcperez2861 28 дней назад

Good job All is ok, but next time don't forget the jack stands. ✌🏽

@MobileCarMechanic 28 дней назад

Yep, thank you.

@dano727 17 дней назад

Great video thanks! I've had my issues with this task... 😢

@MobileCarMechanic 16 дней назад

You can do it!

@rich1953 6 месяцев назад

One thing I would like to add, it is best practice to line the channel on piston face with nipple on break pad.

@MobileCarMechanic 6 месяцев назад

Thank you for the suggestion.

@boinger1988 11 месяцев назад

You installed your caliper pins in the incorrect order. The pin with the rubber bushing and the line machined around the flats goes on the top. I removed both pins from my caliper bracket yesterday and got them mixed up. I had to go find an exploded diagram online to see where they went. Supposedly the rubber bushing has something to do with mitigating vibration when braking...

@MobileCarMechanic 11 месяцев назад

Thanks for letting me know. Got distracted and forgot which order. I know it helps with evening out the travel to wear pads down evenly. Gonna swap them in the correct order. Cheers!

@earthenergyhex 2 месяца назад

thanks

@MobileCarMechanic 2 месяца назад

You're welcome!

@AngelerFils 4 месяца назад

Thanks!

@MobileCarMechanic 4 месяца назад

Glad our video helped. Greatly appreciate the donation. Cheers!

@priyanshukant3433 2 месяца назад

do you have videos on how to do brake flush on honda 2017

@MobileCarMechanic 2 месяца назад

I do not at the moment. Thank you for the suggestion.

@beexiong9047 11 месяцев назад

Great video

@MobileCarMechanic 11 месяцев назад

Thanks!

@richardfabrizio8998 8 месяцев назад

Pretty good job. But you didn’t torque bolts on caliper 37 ft lbs. didn’t lube hardware for disc brakes. Didn’t use silicone on slider pins ( not brake grease ). Minor things but makes a difference. Thanks

@MobileCarMechanic 8 месяцев назад

Thanks for the info

@CoachTed2023 8 месяцев назад

The tool to rotate the caliper back was new to me. Awesome, Thank you. i spent an hour trying to use c clamp, cussing and wondering what i was missing.

@MobileCarMechanic 8 месяцев назад

Glad it helped

@carlreich 4 месяца назад

Dude! Me too. I was so mad it wouldn’t compress😂

@nickolasrosenthal7757 3 месяца назад

Were do u get one of them

@robm321 2 месяца назад

@@nickolasrosenthal7757 Amazon for cheap

@austinruten5195 Месяц назад

If I could add a picture I would I snapped a 12 inch c clamp using a 15 inch cheater bar for leverage before I came to this video

@mikem1129 2 месяца назад

Other than the switched caliper pins, my only other issue is the rock chock!!! 🤣

@MobileCarMechanic 2 месяца назад

Thank You for your feedback, Needed to include a little bit of nature in our video haha

@mikem1129 2 месяца назад

@@MobileCarMechanic 😂

@messynate 15 дней назад

Was the handbrake off the whole time

@MobileCarMechanic 13 дней назад

Handbrake was off, Some honda/acura models let you retract without a tool such as this one and causes no electrical issues.

@carlreich 4 месяца назад

You must be a renter. Spraying and lubricating with nothing underneath 😂

@MobileCarMechanic 4 месяца назад

Haha it’s my friends driveway.

@carlreich 4 месяца назад

OMG, is he still your friend? Brake cleaner eats everything and that includes asphalt

@carlreich 4 месяца назад

I appreciate the video, had no idea that the rear piston was a screw type. Tool ordered to be delivered tomorrow

@mikegrizwold2522 2 месяца назад

😄

@timgerhardt1653 5 дней назад

Next time please don't support the car on a Harbor Freight jack without jack stands or at least the removed wheel. And I didn't think that you shouldn't tighten with a socket on an impact drivers.

@SoCalGeo 5 месяцев назад

So no need to open up brake reservoir when pushing caliper piston back?

@MobileCarMechanic 5 месяцев назад

If your just doing 2 axles then you are good to go, if you did all 4 wheels then it may leak.

@SoCalGeo 5 месяцев назад

@@MobileCarMechanic ok, good to know. Thanks for the reply.

@Budgeez 9 месяцев назад

Should try a better angle , couldnt really see much and couldnt see how far out the break pads supposed to go

@MobileCarMechanic 9 месяцев назад

Thank you for the feedback! Cheers!

@user-wm4bo4nj8l Год назад

hello and hi what is the torque spec for honda hrv 2020? on the front and rear brake thanks all the bolts

@MobileCarMechanic Год назад

50 N-m (5.1 kgf-m, 37 lbf·ft) Front Caliper 108 N-m (11.0 kgf-m,80 lbf·ft) Front Caliper Bracket 35 N-m (3.6 kgf-m, 26 lbf-ft) Rear Caliper 108 N-m (11.0 kgf-m, 80 lbf-ft) Rear Caliper Bracket

@user-wm4bo4nj8l Год назад

@@MobileCarMechanic hello also what is the torque spec for spark plugs on honda hrv 2020 with a grease and the gaping on spark plugs should i change it or leave it when i buy the spark plugs?

@Striker50_ 11 месяцев назад

Careful not to overtorque those guide pins, they're only about 15-19lb-ft

@MobileCarMechanic 11 месяцев назад

Thank you for the advice!