DIY Automatic Plant Watering System Using Arduino !!!

Подписаться 797

Просмотров 152 тыс.

50% 1

Hey guys im back with another vedio, today in this vedio i will show you how to make automatic watering system using Arduino.
Code of this project - drive.google.c...
Circuit diagram - postimg.cc/ZBt...
Products used in the project 👇
1.Arduino uno - www.tomsonelec...
2. Water pump -www.tomsonelec...
3.jumper wire - www.tomsonelec...
4.relay module -www.tomsonelec...
5.soil moisture sensor -www.tomsonelec...
6. forex sheet -amzn.eu/d/74iIaaB
7.6mm pvc tube -dl.flipkart.co...
.
.
.
Song: Ikson - Lights (Vlog No Copyright Music)
Music promoted by Vlog No Copyright Music.
Video Link: • Ikson - Lights (Vlog N...
#NoCopyrightMusic #VlogMusic #VlogNoCopyrightMusic

Опубликовано:

14 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 137

@ITWorksSoftware Год назад

The pump should be submerged at all times or you can ruin it. Thank you for the video, nice project. 👍

@bulauansherylangelim.3709 Год назад

OMG I watch so many videos to finish my project but your video help me to understand it better. thank you so muchhhhh

@rajeevprabhu1954 8 месяцев назад

Is the code correct?

@bulauansherylangelim.3709 6 месяцев назад

@@rajeevprabhu1954 yes po

@rajeevprabhu1954 6 месяцев назад

@@bulauansherylangelim.3709 yes it worked for me as well....btw you are just 2 months late 😂

@piashaynnemanayon6744 5 месяцев назад

@@rajeevprabhu1954 hi guys, can u explain it to me?

@rajeevprabhu1954 5 месяцев назад

@@piashaynnemanayon6744 yea sure....i will recommend you to search "How to make Automatic Plant Watering System using Arduino UNO and Soil Sensor" on youtube there is video on channel named techie lagan.....you can blindly copy that video and circuit diagram is also very nicely given there 👍

@lloydgarcia8832 10 месяцев назад

Hello, why does the pump still pump water even the moisture sensor gets wet? Thank you

@FLOATINGMLEM Год назад

hello, i've met a problem. my pump is not starting and i did everything u did there, i even have almost the same components as you do. my moisture sensor is set on digital, should i control it from that screw from the module or smth? i tested it rn, if the sensor is in water at the start of the test, pump is not starting, i take the sensor out, pump starts, but after that, if i put the sensor back in water, the pump won t stop, or it will be delayed by like 5-10 sec

@TNS_edits10 11 месяцев назад

Try using another power source for the pump

@FLOATINGMLEM 11 месяцев назад

@@TNS_edits10 i tried 3 different powersources, 3 different types of moisture sensors and also tried both analogyc and digital signals for the sensors and still not working XD

@TNS_edits10 11 месяцев назад

@gabibotea700 then Idk btw I m very young m in 7th and doing this for a project

@ROBO_MAC 11 месяцев назад

It may be the issue with the sensor

@ROBO_MAC 11 месяцев назад

Try testing each and every board by uploading example code !!

@nteach8137 Год назад

U r life saver for my project. I watched pther tutorial but could not understand. Thank you

@notgrimm 10 месяцев назад

Won't it overwater the plants since it pumps water everytime it gets dry? Some plants need drying-out in between waterings.

@AAgunner 9 месяцев назад

Was thinking the same thing. Most plants can take quite some abuse when it comes to underwatering, and still make an amazing recovery. But root rot is pretty much a death sentence...

@kizuffy3338 6 месяцев назад

hello, can i add a program app into this watering system? like i can toggle the between auto and manual click(manipulate the water volume and time)

@reddy8533 21 день назад

where do the positive and negative lead of the pump go?

@uzairshaikh7955 13 дней назад

See diagram on 1:16

@chzbllz Год назад

You will be a life-saver if this works for my project to succeed

@Draken8998 День назад

Can i use 12v pump with 5v relay?

@noiresama7222 Год назад

Hello, can I still use the 5V relay module if I'm using a 12V DC power source and a 12V pump?

@ROBO_MAC Год назад

Yes but for more efficency use a 12v relay

@mr.moonface4784 9 месяцев назад

i used something similar,but instead or an Arduino i used an ATTiny 88 programmer board wick works nicely

@ryanahmadruzain467 Год назад

pls help me connect the mini water pump to relay

@nibinarayanan3621 Год назад

Bro how power is supplied to ardino and

@ROBO_MAC Год назад

Here I have used 2 power supply, one for ARDUINO and other for PUMP so that there will be no delays in working

@megannarzoles5940 13 дней назад

@@ROBO_MACwhat kind of power supply?

@rcravigaming1502 11 месяцев назад

Hi, Can I use rain drop sensor instead of soil moisture sensor in

@ROBO_MAC 11 месяцев назад

@musiccrabbeatz3312 2 года назад

Very helpful 👍 Thank you Technoliq ❤️✨

@eziz7468 6 месяцев назад

Can you make a vid for a simpler system? I was thinking of a timer so like every 3 days it waters the plant for like 10 seconds. Also instead of using a pump just put the water container above the soil and rig a valve to open and close. Could that work? Seems a lot simpler and more effective since there arent as many components.

@gxh6497 6 месяцев назад

yes will work

@bansheeboys7839 Год назад

Did you use the normally open on close on the relay

@ROBO_MAC Год назад

Yes

@Rithraksa_Nheb 4 месяца назад

can i use the 12v battery pack on both Arduino and water pump?

@assan-pv9wb Год назад

thanks for the video btw can i add an lcd display to this project and what should be changed in code ?

@ROBO_MAC Год назад

Yes, of course

@DKSkaHub 10 месяцев назад

How I will power the circuit...I guess from Hw battery

@nisargrakeshkumarpatel5912 Год назад

I don't have 12 volt power jack so can I do cross connection an apply code will it work

@ROBO_MAC Год назад

Yes

@HarperJones-r5k Месяц назад

hello, for the relay module where does the cable go, not the ones that already connected to the water pump but the one where It a full cable and it goes off screen at the end

@ROBO_MAC Месяц назад

To the power supply

@testinglive3787 13 дней назад

is the code that is shown in video is different from code which is there in description??

@Trying_Everything 11 дней назад

how much money is it going to take to buy all the parts

@infj9967 Год назад

What is the 12v power jack? Need to connect to? I searched on the Google and it's not the same as in the video

@ROBO_MAC Год назад

It is the power supply for the relay

@infj9967 Год назад

@@ROBO_MAC I see.. thank you!

@marciano.abrantes2564 Год назад

Can you help me sir . Why is that , when the sensor is wet the pump still works ?

@marciano.abrantes2564 Год назад

I followed all the steps but the pump don't stop even it is wet of water

@ROBO_MAC Год назад

The sensor may be faulty

@FPaan Год назад

bro. sorry for disturb you. How you connecting relay with dc water pump? it was not clear to follow your step on this video. please respon . Thanks a lot

@ROBO_MAC Год назад

Connect the pump's +ve to N\C of the relay and -ve to any power source and +ve of the power source to the COMMON pin of the relay

@Amy_desu 10 месяцев назад

I also couldn't figure this out

@olivermag-tz7mg Год назад

Hello, this is such an awesome project. How would I connect the same relay module and sensor to an Arduino pro mini? Is this possible, this would be such helpful to know. Thankyou very much

@ROBO_MAC Год назад

You can connect anywhere in the digital pins , you should change the code accordingly

@rohititzmerohit6251 Год назад

@@ROBO_MAChlo sir plz sir kl ye mera project h sir work nhi kr raha sir solution digiye

@thegoat_isthebest Год назад

thank you i might win the science fair.

@Black_editor_official 3 месяца назад

Really

@Black_editor_official 3 месяца назад

Reply me bro i have a problem for this code

@jovancaparal4808 Год назад

okay lang ba gumamit nag relay with optocoupler instead normal na relay?

@kristinanadinelacno4340 Год назад

hi po okay napo ba project niyo?

@ROBO_MAC Год назад

English?

@veselinkovacevic 11 месяцев назад

Is there one inch water pipe arduino controler?

@Achmad-Adji 10 месяцев назад

can you replace the power jack with a battery?

@ROBO_MAC Месяц назад

Yeah

@thehoneybeesshow 10 месяцев назад

Hey will that double relay work?

@KUKM31 Месяц назад

Brother I appreciate you I want to know one thing that just the code is applied in the circuit isn't it?

@ROBO_MAC Месяц назад

Yeah?

@AsifAli-dm7ri Год назад

Hi! Actually I wanted to ask what If I use 2 relay modules will it still work with the same connections and code .

@ROBO_MAC Год назад

Yes

@RajyalakshmiParasaram 7 месяцев назад

Which battery is used for this

@iehvinceeartajo1460 Год назад

what 12Volts battery did you use? Do we use regulator for this?

@ROBO_MAC 11 месяцев назад

No, Arduino Uno supports 12v

@svkrbeats8954 Год назад

How did you given power supply

@ROBO_MAC Год назад

Here I have used 2 power supply, one for ARDUINO and other for PUMP so that there will be no delays in working I have given external power supply to the pump.

@hollyteper3269 5 месяцев назад

What was the app you used when you programmed the code, I can't find it?

@ChampaArya-ct8ph 2 месяца назад

Idk broo😮

@telugustatusvideoscontents1661 10 месяцев назад

Is it need battery

@CreativeKranti Год назад

The required Code is not working properly. pls have you other code

@ROBO_MAC Год назад

It is working properly

@yashwaghmareyash999yt9 2 года назад

Best model 👍👍👍👍👍👌

@secondtime9625 10 месяцев назад

Selangnya beli dimana bang?

@athin__6906 Год назад

Thank you 🎉.this is a video I want

@ChampaArya-ct8ph 2 месяца назад

What will be the amount for this thing

@ronak9631 5 месяцев назад

How do i connect the battery ??

@jezryllekeinbinunag121 8 месяцев назад

What app you use to insert the code?

@hollyteper3269 5 месяцев назад

That is what I am looking for too

@nurismahimanibtmohdizan5600 Год назад

Hi! Can i have the schematic sketch for this

@dacianfd8418 Год назад

This project is working also without the arduino board.

@ROBO_MAC Год назад

Yes, you can try replacing the microcontroler with any ic's like 555

@Whiteline01812 Месяц назад

is the code supposed to fail?

@devprajapati8397 Год назад

Boks kese banaya?

@ROBO_MAC Год назад

Using Forex Sheet

@kristinanadinelacno4340 Год назад

the code is copied from another source,can you provide the exact code?

@hollyteper3269 5 месяцев назад

That's what I am looking for too!

@MagesKasi Год назад

How much did you spend for this ? Bro

@jimuelcastillobasbas1896 5 месяцев назад

why the code from the video is different from the code on the description

@hollyteper3269 5 месяцев назад

That's what I am saying!

@kmalikarjuna4546 3 месяца назад

Where u connected code sir

@radhey2001 Год назад

Total cost?

@ROBO_MAC Год назад

Under 1k

@spikesakura8321 6 месяцев назад

Can you give me the code with blocks

@crazyxyz7371 11 месяцев назад

The code is not working sir 😅

@rajeevprabhu1954 8 месяцев назад

Hi did you find correct code

@jezryllekeinbinunag121 8 месяцев назад

What app you use sir?

@MoahamadMnini 6 месяцев назад

int water; //random variable void setup() { pinMode(3,OUTPUT); //output pin for relay board, this will sent signal to the relay pinMode(6,INPUT); //input pin coming from soil sensor } void loop() { water = digitalRead(6); // reading the coming signal from the soil sensor if(water == HIGH) // if water level is full then cut the relay { digitalWrite(3,LOW); // low is to cut the relay } else { digitalWrite(3,HIGH); //high to continue proving signal and water supply } delay(400); }

@MoahamadMnini 6 месяцев назад

@@jezryllekeinbinunag121 Arduino droid