DIY Basement Wall Framing (How to Finish a Basement Ep. 2)

Подписаться 304 тыс.

Просмотров 452 тыс.

50% 1

🛠🧰 Tools and Materials Needed: amzn.to/3JDDABP
Lean how to frame basement walls with this DIY Basement wall framing tutorial video. In this video, I show you how "I" framed my basement walls - not necessarily how YOU should frame yours.
To Frame Basement Walls, you will need the following tools and materials 🛠🧰:
- 2"x4" Lumber (bottom plate must be pressure treated)
- 6' Level (Straight edge): amzn.to/3HowUDn
- Framing Nailer: amzn.to/3ViKOOe
- Carbide Tipped Masonry Bit: amzn.to/3PJAWf8
- Tapcon Screws: amzn.to/3vbwwEg
- Chalk Line: amzn.to/3YGqjxK
- Hammer Drill: amzn.to/3G8tuqP
To frame a basement wall, you will want to follow these general steps:
1. Position the bottom plate, top plate, and wall studs in place.
2. Mark the stud spacing (16" on center) on the top and bottom plate.
3. Cut your basement wall studs to length and position them in place between the top and bottom plate.
4. Nail the studs to the top and bottom plate using a framing nailer.
5. Lift the wall into place.
6. Secure the bottom plate to the basement floor using tapcon screws.
7. Secure the top plate to the floor joists above using a framing nailer.
For more information on how to DIY basement wall framing, you can read my "how to frame basement walls" blog article linked here:
atimprovements...
This is Episode 2 in my "How to Finish a Basement" RU-vid Series. In this series, I will show you how to finish a basement (DIY) from start to finish. Below are the previous videos in the series:
Episode 1: How to Install Rigid Foam Insulation
• How to Install Rigid F...
Be sure to subscribe and hit the notification bell so you don't miss any future videos that are part of the Basement Renovation Series!
Follow me on Instagram: / atimprovements
Check out my Blog: Atimprovements.com
Subscribe to my RU-vid Channel ⬇️ www.youtube.co...
Check out my Website for additional DIY Content: atimprovements...
▬▬▬▬▬▬▬▬▬▬▬▬▬
🎥 MY RU-vid GEAR
Camera (Iphone Max): amzn.to/3d5HxSo
Microphone (Maono Condenser Mic): amzn.to/3RCAb7N
Tripod: amzn.to/3Rz5Gj3
Mini Tripod: amzn.to/3Rvt2WM
Lighting: amzn.to/3d4QdZ5
▬▬▬▬▬▬▬▬▬▬▬▬▬
🛠🧰 TOOLS THAT I USE
Carbide Tipped Drill Bit: amzn.to/3S0hdIM
Tapcon Screws: amzn.to/3OxEWxh
Drill: amzn.to/3JICKkk
Tape Measure: amzn.to/3HaTWgE
Circular Saw: amzn.to/3BFotC4
Masonry Drill: amzn.to/36yP1JW
Level: amzn.to/3HowUDn
Hammer: amzn.to/35fIpiT
Chalk Line: amzn.to/3MwSDg8
Clamps: amzn.to/3HLqwpK
Drill: amzn.to/3JICKkk
Sawzall: amzn.to/3HcdeSI
Circular Saw: amzn.to/3BFotC4
Jig saw: amzn.to/3I6lcyd
Air Compressor: amzn.to/34TatJf
Framing Nailer: amzn.to/3JGpBYU
Roofing Nailer: amzn.to/3BEAuYF
Orbital Sander: amzn.to/34UwlUD
Bar Clamps: amzn.to/3JjFrJe
▬▬▬▬▬▬▬▬▬▬▬▬▬
Thank you so much for watching!
*All content on the Andrew Thron Improvements RU-vid channel reflects my own opinions. Please seek out guidance of professionally trained and licensed individuals before making any decisions. Links in the description may be affiliate links.

Опубликовано:

26 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 206

@busurkind Год назад

I just got 89k estimate for my 700sqft basement and that’s why I’m here

@GreatRemembrance Год назад

Haha this comment is the best! Best of luck. That’s why I’m here too 😂

@mr_fuji_mintsmr_fuji_mints9873 Год назад

Me too! Literally same size and price! 😂

@416pp Год назад

Wtf you just need walls.. no rooms and 89k? Bruh.. even in expensive markets in Canada 700 sq ft shouldn’t run you more then 40k

@adelelsayed6711 Год назад

Me too

@busurkind Год назад

@@416pp I wanted an office, full bathroom and playroom there. the most expensive thing is plumbing that includes drilling concrete and installing in-ground pump for it

@dylansellers9588 Год назад

Did you mean 1 and 1/2" + 1 and 1/2" = 3"??? Thanks for the video. It gave me the confidence to get started and became even more valuable to re-watch after starting.

@303pearson 8 месяцев назад

Annoying that he hasn’t addressed this as I am trying to figure out measurements as we speak and immediately was like hang on… 1/2” + 1/2” is not 3”🤦‍♂️wtf

@rhettskeel7669 6 месяцев назад

Hopefully, you meant the thickness of 2 2x4s. The easiest way is to lay down two 2x4s on the floor against the basement wall then measure the distance from the top 2x4 to the floor joist. No subtraction needed.

@gavinframent9383 Год назад

This is what everything needs. The way you present and edit your videos is key to learning. Whether it's nursing or car repair, your formula works. I love watching your videos.

@andrewthron5107 Год назад

I really appreciate it! I am glad it's helpful!

@albertosantana5506 3 месяца назад

I’m here because they wanted 40k

@Kathayne636 Месяц назад

lol, it's not like it's rocket science either. you can do it.

@tacticalchannel9433 4 дня назад

This

@cadayx Год назад

Framing my basement right now. Thanks for this great video!

@andrewthron5107 Год назад

Good luck with your project!!

@RADIO-FREE-AMERICA Год назад

A lot of planning goes in to this, for sure! I could never remember all these instructions! Cheers! Gonna be a cold 🥶 weekend!

@AndrewThronImprovements Год назад

So much planning! And yea it’s gonna be a cold one for sure. Thanks for watching, Thomas!

@ClubMayview 2 месяца назад

The rigid foam prices are flat out robbery

@1NationNetwork 12 дней назад

Wow thanks for this!

@weekendhomeprojects Год назад

What are the do's and don'ts of insulating above ground basements? I hear the walls like to breath.

@jeremythomas7544 20 дней назад

@weekendhomeprojects 1" or better for foam board on block or poured wall 3/4 " gap away for wall framing insulate with rock wool it's mold and water resistant. You want to stop wall from breathing inside.

@weekendhomeprojects 20 дней назад

@@jeremythomas7544 glue the foam to the block?

@jeremythomas7544 20 дней назад

@weekendhomeprojects yes with foam board glue Loctite pl300 0r liquid nails foam glue Tape the seams. You can screw it with tap cons if needed. You can either use xps foam *extruded foam) or eps foam (Styrofoam) foam. Both are mold resistant

@jveeroom112 3 месяца назад

Awesome vid. Helps a lot. Unfortunately I have no space in my basement to build the wall on the ground due to posts located in inconvenient places. So have to frame in place much like this

@conniewright8080 Год назад

The best thing is 'you know how to do it' without hiring someone, which is very expensive & they might not do it right. I helped my husband, after his death I had to hire to complete some of the work. It was a nightmare. They ALL say they can......great job sir.

@AndrewThronImprovements Год назад

I could not agree with you more, Connie! Appreciate you watching!

@timc2797 Год назад

Why is there space between the insulation and the 2x4 wall? Do u recommend putting plastic sheeting between concrete block and the insulation? Thank you I advance Tim

@bobbysantiago5783 20 дней назад

Great video. 👍

@timdaniels2094 Год назад

Thanks!

@BigSkyJason Год назад

1:03 I think you mean 1-1/2", not 1/2".

@AndrewThronImprovements Год назад

Correct, my bad!

@five-forty3431 Год назад

Great explanation, thank you!

@evanmcguire9220 Год назад

Great video! What software was that, that you used to show the California corner?

@dtesla9086 Год назад

couple of questions..dont you need small space between studs and wall,,i think i read half inch,,as well do you need vapour barrier under bottom plate

@rhdata05 Год назад

So watching this among other videos here, it seems that the proper way to install studs to basement walls is to hammer/screw them into the ground via piece of pressure treated wood, not into the foundation walls. That is good to know

@jiovannijiuseppe Год назад

You want green wood only for the 2x4 touching the floor; you should have anything vertical 1/2 inch from the wall because concrete naturally has moisture

@JonathonRodger 4 месяца назад

You didn’t leave an air gap and therefor you’ll have frost and moisture build up on the insulation and surface mold behind your walls. When building off concrete walls you need 6.5” to surface of drywall with a 2x3 framed to give you enough space behind the wall to have what I call mixing air where your hot air that’s escaping the house will hit the wall where the cold air is penetrating the concrete wall from the outside in and with no mixing air space you will cause too much temperature difference in one specific area and thus moisture build up and surface mold. Rest of the video seems fine. Your walls could also start frosting on the inside of the drywall too if you have a newer home and is really air tight…

@alfredot.8426 6 дней назад

What about the r-10 rigid insulation? That also acts as a moisture barrier.

@alfredot.8426 6 дней назад

I would cut studs individually if the floor is uneven. If you frame the whole thing at once and the slab is uneven, you would be using or abusing shims to make it fit

@kwb402 6 месяцев назад

We do it because it’s fun.

@jayflaggs Год назад

How would you frame around a protruding cement baseboard?

@samrala777 Год назад

Is there a different way of framing for people living in colder states and/or Canada? Due to the potential of shrinking and expanding? Thanks!

@cameron6740 Год назад

Vapor barriers may be different as well.

@lewis6699518222 Год назад

Yes, use a one inch expansion gap between bottom plate and pressure treated plate on floor. Nail thru to allow for any potential heaving of the floor as it doesn’t run thru into your joists.

@taoyoka 3 месяца назад

Amazing job.

@AndrewThronImprovements 3 месяца назад

Thanks!

@PeterKeefe 10 месяцев назад

Great video series! I'm about to frame out a room in the basement. Wondering: do you wish you had done double bottom or top plates?

@steverogers2603 Год назад

Thanks for your video. My only suggestion would be to slow it down a bit.

@nw4980 11 месяцев назад

Great vid thanks for sharing. Maybe I missed this but are metal studs cost prohibitive or not appropriate for basements or both? Also, plans for underlayment for flooring? Thank you!

@mohammadabrahim6517 Год назад

When installing the frame should the frame be installed to the ground first air to the floor Joyce first? And how will I get it perfect without the frame being messed up. Would I use a shim?

@BrandonLubanski 7 месяцев назад

Bottom firstborn easier, and tapcons or Ramsey fasteners will hold easier...then yes shim the difference and fastener the top

@donnell9238 Год назад

Fantasic video bro.

@AndrewThronImprovements Год назад

I appreciate it!

@mikebursic2755 Год назад

Should basement walls not be floating walls?

@tacticalchannel9433 4 дня назад

Whats the modelling software? Thatd make my life so much easier

@ameann 3 месяца назад

Hey, quick question. How do you get the OSB sheet behind the stud wall frame and fixed to the stud frame whilst mainting the gap from the stone wall? My mind is doing gymnastics for something that is probably quite simple. Thanks.

@infiniti2015 Год назад

Great work. Does the crown portion face the interior of the room or the cement wall side once you lift it into place?

@davidc9135 Год назад

It’s personal preference. It’s not so important which way the stud crowns, It’s more important that you stay consistent with your choice. Either way you go about it you’ll either have some planing to do or shimming on the extremely bowed studs. If you don’t own a power planer or don’t intend on buying one then you have your answer. Side note: if you are building your walls on the ground and lifting them in place it’s easier to attach the members when studs are facing crown up

@infiniti2015 4 месяца назад

@@davidc9135That makes a lot of sense. Thank you for the well thought out response. Much appreciated.

@patricksmith3135 Год назад

Great video, as usual. I just thought you were 'teaching' us how to frame 1 stud at a time since you already demonstrated how to pre-construct on the ground then lift whole wall. And I thought you brother was not at home that day, ergo easier on your back to lift 1 2x4 at a time that 12 of them. All in all its a great job and great improvement for your home too. Merry Christmas Andrew.

@AndrewThronImprovements Год назад

Appreciate it, Patrick! Yea, Ryan wasn’t around too much for the basement - but I got his help here and there. Merry Christmas to you too!

@Floidberg Год назад

Very insightful! What software is that you were using to show the California corners?

@AndrewThronImprovements Год назад

Sketchup free version!

@vladb4727 Год назад

what is the difference between green and pressure treated plates? can both be used in contact with the concrete floor? Also, is it necessary to install additional insulation between foam boards and drywall ? is it required? how about vaper barrier ?Thank you !

@justinnelson6169 Год назад

They're the same thing. It is required, because the treatment keeps the moisture (concrete is porous) from rotting out the wood. Newer homes tend to have a vapor barrier underneath the slab, but it wouldn't be necessary for the treated lumber...however, it would for flooring.

@ColleenMullaly Год назад

When you lift the wall into place, are the crowns facing the inside (concrete block) or the outside (drywall side) of the wall?

@AndrewThronImprovements Год назад

I had the crows all facing the inside. But I don’t think it matters all that much as long as they are all facing the same way

@daemoncan2364 Год назад

Is 1" of XPS considered enough insulation / vapor barrier in your locale?

@JohnnyUtah9173 7 месяцев назад

Yes, In the colder climates, R5 continuous + R15 cavity meets code.

@1tufgt 10 месяцев назад

What tool are you using for the framing diagram?

@abelmedina-aispuro3716 8 месяцев назад

Great video

@caryn1158 27 дней назад

What if you have a basement drain in the floor around the perimeter and vapor barrier on the walls I can't screw anything or it will break warranty guessing a can glue to floor, but assuming I can't use or need foam board😅?

@Adam-ue2ig 25 дней назад

Can I frame or do I need a builders license and permit to do this portion? I realize this would be needed for electrical.

@maximusmaxwell100 7 месяцев назад

Is there a code for nail size on non-load bearing partition walls. Everything I read online says they need to be 3.25 inches length 16d (0.148 inches) diameter but the only framing nails for nail guns in the store are 3.25 inches length and 0.120.inch diameter. Am I missing something?

@billygreen3515 Год назад

That was awesome im going to subscribe

@AndrewThronImprovements Год назад

Thanks Billy! Appreciate the support!

@JuanRomero-bf5or 8 месяцев назад

quick question 🧐. If I Wana sheetrock over a cement wall but the wall has 3 different depths. do I insulate with the boarding and then even out the depths before the final sheetrock(I plan on using liquid nails for the project) ; or do I even put the wall first?

@brianbirdsall2167 Год назад

did you put your framing right up against rigid board nor space it slightly away? I am currently finishing my basement and and coming up on the foam board and framing portion shortly.

@csimet Год назад

I left about 1-2" gap... mostly since the concrete walls are rarely poured straight. Not only does it leave a small air gap, but you can build the walls straight. My walls were out about 1" both top to bottom and side to side (along the 24 feet). I'd recommend using treated 2x4s anywhere they contact the concrete directly (especially the bottom plate).

@lyteyearz5810 Год назад

Reply so I can remember to watch this bro! Found you on Instagram. 👏🏽👏🏽👏🏽👏🏽

@AndrewThronImprovements Год назад

Got you bro! Thanks for checking out the channel 👍

@DuaneMondragon 7 дней назад

Why did they not allow for expansion basement floors have a tendency of rising

@adamstone635 7 месяцев назад

What if you already have drywall on your ceiling? Can I just put the top plate to that? I guess that wouldnt even matter huh? Thanks.

@markgross3256 Год назад

Very good series of videos! Very informative.

@AndrewThronImprovements Год назад

Appreciate it, Mark! Thanks for watching!

@LawrenceBautista-g7m 11 месяцев назад

What is the specs of your air compressor? I'm planning to buy a framing nail gun. Great video and keep it up. Thank you.

@josephmercado1408 3 месяца назад

Did you use insulation Batts with the foamular?

@lensreddy 3 месяца назад

What's the circular saw blade thingy called that you cut lumbar with?

@michaelo691 Год назад

How long of a pre-frame is too long? In other words, is there a maximum length of wall I should be preframing?

@justinnelson6169 Год назад

As long as it's solid and anchored at the top and bottom, it shouldn't matter. But, if you have long spans between anchoring points (Seriously, nails are cheap. And, drops in the bucket compared to even just the insulation or flooring) that could potentially cause issues.

@jamesschroeder6407 8 месяцев назад

Really informative video, nice job! What modeling software are you using for the framing?

@AndrewThronImprovements 8 месяцев назад

Thanks! It’s Sketchup - free version

@authenticwater6077 6 месяцев назад

Could you share the links to all the products that you used?

@davevickers4592 Год назад

Thanks for the video! How many Tapcons are needed for bottom plate to stay in place?

@77Avadon77 Год назад

you should use concrete anchors not tapcon screws

@trp2413 11 месяцев назад

Very few I did every other stud bay so about 32” I also used a powder a hated load gun, they are cheap

@patty109109 9 месяцев назад

Sometimes building walls on the floor is a pain getting them into position depending on what’s going on above… also if you make it too tall you gotta redo it. I think I’ve done that.

@barriersurf16 Год назад

Wait, should he have framed the 16OC studs on the ground or no?

@markk5295 Год назад

How far apart should tap con screws be in the bottom plate. I’ve heard every 3 to 4 feet.

@LuisRios-m4n 11 месяцев назад

I just got to the framing part, aren't basement walls suppose to be floating?

@dawnwinter4471 4 месяца назад

How do I get Armstrong to sponsor my drop sealing

@rhemamachaira8763 Год назад

Make two cheater boards for 16" on center measurements. I have ductwork where I can't prefab walls

@RR-vf2bd Год назад

Interesting review! Can you give pricing for items.

@AndrewThronImprovements Год назад

Hi! Check out the video description - most of the tools and materials should be linked there!

@derekgusoff6768 11 месяцев назад

I bought the powder actuated nail shooter thingy. It isn't working. The nails don't go into the concrete.

@joethegamer1709 Год назад

Did you water seal the basement because you should so your flooring won't get messed up.

@scottanthonyd Год назад

How do you recommend sealing the basement?

@deeshad Год назад

I used the same adhesive and supported with 2x4 but it doesn’t stick

@Cccc-ky4vq Год назад

I’ve always heard to use metal studs for framing in the basement whats everyone’s opinion

@bikramsingh2014 Год назад

Very informative. What nail gun and nail size you use for framing projects?

@derekgusoff6768 11 месяцев назад

I tried the dewalt t1000 with 3" fasteners. It wasn't powerful enough.

@JimWatsonTheframingMagician 10 месяцев назад

Nail your bottom and top plate in place and then you can take each stud and stand it up in position and mark it in place by scribing it with a pencil using the underside of the top plate as a guide.

@jiovannijiuseppe Год назад

Isn’t stick framing the best way to do this? Should really be the only way; Reason I say this is because your foundation is going to naturally dip in some places same with the beams you’ll attach a horizontal frame on top to the basement ceiling Because of this each stud is going to be completely different in size, so while it is super tedious, it’s probably the best way to go about it correct?

@AndrewThronImprovements Год назад

That was my logic - but it did take a lot longer… thanks for watching!

@r.j.andmegp2073 Год назад

What software do you use to plan out the project?

@AndrewThronImprovements Год назад

Sketchup! I just use the free version

@tabletappedgameplays7475 Год назад

Somebody really beat you down about the framing, didn't they? You mentioned it in every minute of the video. Lol. Maybe it was you beating yourself up. Either way, this video is very helpful. Thanks!

@tireswing Год назад

Powder actuator drill gun from the wire would have done the job well.

@AndrewThronImprovements Год назад

Totally agree - I noted that in the vid, but I did not have a Ramset nailer at the time of filming.

@snackbardipper 10 месяцев назад

I’m stuck @1:05, 1/2” + 1/2” = 3 inches part ?

@EliVeach 8 месяцев назад

he meant to say 1 1/2 + 1 1/2. 1 1/2 being the thickness of a 2x4

@myuyguncaable 10 месяцев назад

thank you for your videos I have an unfinished 2500 sf. basement. you gave me to encourage

@jasonreed7608 4 дня назад

Fire blocking??

@dabig_guy2204 11 месяцев назад

Basement framing

@hamamunashe 5 месяцев назад

Am here coz they want $9k for a 12 X 12 feet room

@jackryder6732 Год назад

I have a few questions. Can I ask. As few videos dont even respond

@owodeone 4 месяца назад

I got £5k estimate for my 86 sqft. Thats why I am here also

@firemanemt51 Месяц назад

Wait with what math does 1/2 inch +1/2 inch = 3 inch

@josephmercado1408 3 месяца назад

Use the stud master

@cwcadventures9987 Год назад

What does crown up mean?

@AndrewThronImprovements Год назад

crown is the "natural curvature of the board when looking down the boards shortest edge". Hope that helps

@Rellikman Год назад

I read that insulating your inside foundation isn’t good as it keeps the warmth of the home from warming up your foundation where your foundation and soil outside of it can expose the foundation to Adfreezing and possible foundation damage?

@bhadz100 Год назад

How long were the tap cons used for the bottom plate

@AndrewThronImprovements Год назад

I believe 3"

@RealtorDanielMedina Год назад

1/2+1/2=1 and not 3. So idk if I could trust this

@AndrewThronImprovements Год назад

Haha 1.5” + 1.5” = 3 might have been talking faster than I thought

@stephaniebachman397 7 месяцев назад

Does he mean 1 1/2 and 1 1/2????

@AndrewThronImprovements 7 месяцев назад

Yes!

@izznice6969 4 месяца назад

I would recommend not using tape to seal foam. From experience, tape will come undone over time. Leave a small gap and spray foam.

@josephmercado1408 3 месяца назад

This dude would of been done and 16 on center every time 😅

@JasonEllingsworth 10 месяцев назад

im a kid i work with my dad downstaris

@lewis6699518222 Год назад

Be aware, xps is only moisture resistant, most rigid board can only be technically considered a vapour barrier at certain thickness’ depending on jurisdiction. Without water proofing on the outside wall (which I’m sure this guy has as it’s cinder block wall), the cost of xps as a vapour barrier in cold climates as in Canada is extreme, may as well use 2” eps and poly in behind framing, would be a fraction of the price for better r value.