DIY Carbon Fiber Skinning Fiberglass Overfenders | Part 1

Подписаться 9 тыс.

Просмотров 32 тыс.

50% 1

What up fam,
in this video we will be skinning the rear over fenders on the 370z to carbon fender. I will be adding a base coat and adding the carbon fabric on top for it to stick properly. stay tuned for part 2.
Materials used below
black epoxy paint
www.amazon.com/dp/B06XD39K55/...
2k clear coat
www.amazon.com/dp/B00W2D806Y/...
Epoxy resin and hardener
www.amazon.com/dp/B0181M6U5C/...
Carbon fiber fabric
www.amazon.com/dp/B08KYJ6BNQ/...
Scale
www.amazon.com/dp/B078SNH83F/...
brushes, cups purchased at local hardware store homedepot
follow me on Instagram at chrizleyva

Опубликовано:

12 мар 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 39

@bobbysuncin4368 3 года назад

Hard brush roller for next time. Keeps the fibers from spreading out and pushing the fabric down .. prepreg also keeps the ends from fraying

@meroocars4005 2 года назад

Good job 👍🏻

@dennisarriola3807 3 года назад

this is dope!

@Justin8152000 8 месяцев назад

I will always use a strip of duct tape before i cut the carbon where it needs cut/trimmed before I lay it on my piece.. Then cut right through the middle of the tape. This kelps keeps the strands/pattern intact and has always worked very well for me. I tried painters tape once and it just was not sticky enough. Anyone that has cut this stuff and had the loose ends mess up their pattern will appriciate this tip. Hope it helps someone. Great vid

@Chrizleyva 8 месяцев назад

Thank you for the info 🙏

@heemdollas8016 3 года назад

Nice

@revcliqueracing8461 3 года назад

That actually looks crazy sheeeshh did it come out cheaper than if you were to buy a whole carbon panel ?

@Chrizleyva 3 года назад

Yea it would come out cheaper but I'm just doing a top layer if you plan to create your own from scratch it would be more since you would need like a mold.

@humble.53 3 года назад

Nice, the fiberglass fender is made with polyester resine or epoxy?

@Chrizleyva 3 года назад

That I don't know I had already bought it like that I think its epoxy since the back is yellow from fiber glass strands

@JAWS_2K 7 месяцев назад

If my fender is already painted, should I sand off all clear coating before attempting this? Or does it make a difference

@tehrtehr8783 Год назад

Hi can i use acrylic paint to make epoxy black

@gopherchucksgamingnstuff2263 3 года назад

Looks really good.

@Chrizleyva 3 года назад

Appreciate it fam 🙌

@joe9349 3 года назад

Good vid man thanks, I didn't even know what it was called. A, so you can't lay it on the car without taking the panel off?

@Chrizleyva 3 года назад

Appreciate it and you should take it off yo wrap it around

@nickskolsky2560 3 года назад

Brah you need to get your hands on a twin turbo carpet cleaner ! I’m just playing but for reals your garage floor is cleaner than the living room JK !!! You always do ballsy difficult stuff and I admire that my dude 🤙🏼👌🏼🤜🏼🤛🏼

@Chrizleyva 3 года назад

Lmao it just has pieces of the carbon on the floor it's actually clean. Appreciate you fam 🙌

@mikey6.17 3 года назад

Can I do it with black paint on the fender or do I have to sand down the paint completely?

@Chrizleyva 3 года назад

You have to sand it down especially if the paint is peeling because it will just come off

@gearhead3500 Год назад

I have a carbon hood that has clear coat cracks I was thinking of sanding it down completely smooth then adding a carbon material over it thoughts an subjection ?

@Chrizleyva Год назад

If the carbon it's self is not damaged then you should not have to add more carbon on top. You would just sand down, add more resin and then clear coat once all smooth