No video :(

DIY Ferrari 360 Driveway Clutch Replacement Saves Thousands

Подписаться 270 тыс.

Просмотров 295 тыс.

50% 1

My Ferrari 360 has been off the road for over a year, today we are going to change that and start with a complete clutch change. But I am taking it to extremes to show this can be done by almost anyone with the will do have a go. I will perform the FULL clutch change on a driveway with basic tool and single handed using just a jack stand.
Parts required:
Diagnostic Computer: Please contact me scott@ratarossa.com
EMO Affiliate Work Shop manual: bit.ly/3rK6jtV
All Clutch ideas used available here: www.superforma...
Original Valeo Clutch: Part 201680
Flywheel: 181596 HE used in video
ThrowOut/ Release Bearing CRB-360/430-F1S HE used in Video
Ring Gear (6 Bolts) 186157
Flange for Bearing: CRBF-360/430
Clutch sensor 178060
Clutch bolt stop (end of stroke) x 2 205396
Special Tool for EOS pin AV3048
Flywheel washer Spacer 103876
Flywheel bolt x8 201755
Crankshaft spirit bearing 103877
Rear main seal 200323
Clutch alignment tool CAT-360
Cotter pin 14158570
O ring Gasket (oil filler) 176388
Screw for Sensor bracket x2 14358524
O rings (behind clutch flange) x2 166432
Rear cover Gasket (to change Rear main seal easy) 170529
/ ratarossa
/ ratarossa
/ ratarossa
For Sponsorship Enquiries.
Email: scott@ratarossa.com
www.ratarossa.com
#ratarossa #AD #ferrari

Опубликовано:

5 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 842

@DestroyerWill 3 года назад

Ferrari Workshop: it’s a 4 person job. Scott: I’m going to do it with one hand and hold a camera with the other.

@flir67man84 3 года назад

With flipflops!

@Ratarossa 3 года назад

don't forget the sunglasses

@JayEmmOnCars 3 года назад

@@Ratarossa and a hot cup of Joe

@VortechBand 3 года назад

Well, it doesn't count as his uncle is Bob

@Dolebludgeoner 2 года назад

I understand the multitasking with the camera, but put a rubber mat down under the flywheel to avoid the starter ring gear impacting the hard concrete next time... or slip a thong/flipflop under it

@nickhannaford3253 3 года назад

My OCD is freaking out every time Scott puts a tool or flywheel on the bodywork 😱😂.

@Woods_Hiker 3 года назад

I thought the same when I saw him jostle the flywheel on the left rear quarter panel :p ;) Its his car though and he knows what bits he values or are due for a refresh anyway. Very thorough job Scott that would give me confidence if I were to attempt it. IOWs- I would be terrified withpout first watching one of Scott's vids

@Cenetoceki 3 года назад

Same when he was bleeding the lines and it started to rain. Minute later he said "it looks a bit milky" haha

@fredpinczuk7352 3 года назад

Or the engine intake uncovered.

@767dag 3 года назад

Me too

@A.I.Michelsen 3 года назад

Just about the same I was thinking

@chompeyboy 3 года назад

Most mechanical workshops couldn't do what you just did in your driveway, often one handed. That's the truly impressive part. Seriously fantastic work mate, keep sharing.

@Ratarossa 3 года назад

Wow, thanks!

@chrisk5305 3 года назад

The most amazing one man band on a driveway seen in 2021.

@MrMairu555 3 года назад

One of the most impressive things about this video, is the fact you completely removed the transmission just for the sake of your RU-vid followers. You actually created additional work for yourself, just to make our experience better.

@wernerdanler2742 3 года назад

I've taken on some complicated jobs on cars and other machines on my own and wouldn't hesitate to do this one if I were 40 or 50 years younger. The sense of accomplishment when you complete a job like this is priceless! No left over bolts or nuts either. Lol

@elliottd770 3 года назад

Why would anyone thumbs down this video.? This fella should have 1 million subs by now. Great video thank you.👍🏻👍🏻👍🏻

@Samcrac 3 года назад

Hey Scott, excellent job mate. I really appreciate how you got every single little seal possible while you're in there; If you take this car to Ferrari, they literally don't touch about half the amount of parts you replaced unless requested or unless there is obvious failure.

@Ratarossa 3 года назад

Cheers buddy, a very wise fella RU-vidr told me about half of them wink wink.

@clifbradley 3 года назад

I find this comment absolutely epic considering Sam literally just released his video on it. I know when that video was done because I live close to him and can tell by the weather. But either way, awesome

@markusklose11 3 года назад

Nice removal-job of the engine-bearing with the "stiffler". 👍

@jeffmac3071 3 года назад

@@Ratarossa Scott, definately need to look into getting a few chickens and cows to boost your subs. Maybe Samcrac can let you some of both.

@TROdesigns 3 года назад

Facts, and this is the case with a lot of mechanics

@sruk 3 года назад

I don’t want any more stick about my white trainers I just watched some dude change a Ferrari clutch wearing flip flops

@Ratarossa 3 года назад

Ha ha ha I knew you would spot that

@pm1104 3 года назад

Dude or Dildo………..at least you have protection…….what if he’d dropped a spanner on his toe……….!

@PeteCourtier 3 года назад

😂If Ratarossa was an Aussie :- Man changes Ferrari clutch wearing thongs😮🤢

@spyder_man 3 года назад

That are safety sliders, all good 👍🏻

@organiccold 3 года назад

Hahaha nice one Rob lol

@kenvaleriano613 3 года назад

Samcrac is crying over watching scott change a clutch with its bits and bobs in 1 video while it took him more than a year and the car havent moved since

@PixelVogue 3 года назад

LOL i was about to post the same thing! Sam the clown

@PeteCourtier 3 года назад

Yeah, but his “Mom” keeps tiring him out😮

@guesswho8628 3 года назад

@@PeteCourtier telling me you wouldn't? Loool

@PeteCourtier 3 года назад

@@guesswho8628 well😂 Throw in Xev Bellringer and party time🥰

@machiningbasics1729 3 года назад

Most of us will never work on a Ferrari but I think we could all have a go now you’ve shown us how

@patrickhostler5939 3 года назад

I don’t own a Ferrari, but I still find watching these films fascinating and relaxing

@1PotatoeMasher1 3 года назад

Maybe one day your friend will give you an amazing deal on their classic Ferrari and this could come in handy! Until then it’s good entertainment.

@xXsatx210Xx 2 года назад

Same 😆

@xXsatx210Xx 2 года назад

I watched the whole thing without skipping forward 🤙🏽

@awedwardscleaningsolutions 3 года назад

These are my favourite kind of Ratarossa videos. Love the way you use your Ferraris like they're some old Citroen and not in a garage under sheets scared that one spec of dust touches the paint. Top man 👍

@Ratarossa 3 года назад

Thank you very much!

@awedwardscleaningsolutions 3 года назад

@@Ratarossa great content mate. You never see stuff like this and this in detail on these kind of cars. Cant wait for the BBI to get back together. Love that era of cars 👌

@samuelbartle7136 3 года назад

Love the way you lump the fly wheel around on the rear quarter 🤣 proper use of a proper car 🚗 👌 👏 👍

@massimomerisio4829 3 года назад

I got scared when dragging the crown fly on the fender .. :D

@anthonythomas9456 3 года назад

Why have you not got more subs this guy just changed a clutch on his ferrari on a drive way himself

@mikaeljonsson4686 3 года назад

He's King! 😊👍

@deonmeyer9127 3 года назад

That was cool reminded me of a Wheeler Dealer episode on steroids well done.

@_RicksGarage 3 года назад

Great video. Thanks for taking the time to film it despite it making the job ten times longer! You didn’t even need to completely remove that gearbox out of the engine bay but you did for the sake of making this video. It’s good to know I’m not the only one who makes life harder for myself just for the sake of filming haha. Enjoying the content. Keep up the enthusiasm 👍🏼

@deanbailey2183 3 года назад

RataRosa one man band, no no conductor of his own Italian orchestra Cheers

@stevierea70 3 года назад

You have some set of balls to tackle such a huge job, in your driveway, in a pair of flip-flops. I don’t think even manscaped could tackle them balls….. they’re huge! Fabulous video. Your knowledge and skill is an absolute credit to you and it was intriguing to watch. Thank you for such detailed and entertaining content.

@Ratarossa 3 года назад

Ha ha ha Stevie .... I'm packing a couple of space hoopers down there !

@zxr750boy 3 года назад

Great to see a car like that getting worked by a DIY'er. Fab job!

@ProdicalMan 3 года назад

Only channel I have the bell notification on for

@Ratarossa 3 года назад

much appreciated

@mstathis1979 3 года назад

Servicing Ferrari in sandles. One of a kind you are man.

@alannewland5933 3 года назад

We changed the cam belts on my 308gtb and were pleased with ourselves. You are a legend.

@Czechbound 3 года назад

This was really fantastic. I think the main benefit of videos like this is that they give us confidence to tackle thinks that stop working/ need replacing/ repairing on our cars, whatever the type/ value/ condition of the cars. Doing your homework beforehand, diagnosing the problem, confirming the initial diagnosis, ordering the right parts, having the right tools, and following the instructions seem to be the way to do. Well done, that was really great !

@Ratarossa 3 года назад

thanks you buddy, kind words

@kieranshanley7365 3 года назад

Great to see a return to classic ratarossa content. You make it look so much easier than samcrac !

@marksbikeexports5123 3 года назад

I was wondering if Sam set his clutch properly.... Probably not

@Goc67 3 года назад

I love that you are working with "Hugh Jackmans" on your drive way.

@B2daBaZ 3 года назад

So much respect and admiration for this, changing a Ferrari clutch on a drive way outdoors in uk weather in flip flops🤣🙌🏻👌🏻

@paulthompson5416 3 года назад

Well done Scott 👍🏼 Making a fool out of the £200 per hr Ferrari "Technicians" that suck air through their teeth when they hear 360 clutch 🤔🧐😬 And here's Scott the one man tech team changing it on the driveway with one specialist spanner and his Puma flip-flops 😂😂😂😂👏🏼

@massimomerisio4829 3 года назад

flip-flops are the best, accident prevention! :DDD

@mgc1970 3 года назад

The Puma flip-flops keep it real!!

@conniebenny 3 года назад

That might be easy for you, but to me that was incredibly impressive! Well done on having the skill, knowledge and confidence to tackle such a job yourself... And you also saved yourself God knows how much by not taking it to a Ferrari mechanic! Top marks, mate :-)

@nigeljames1109 3 года назад

A great source of education for those with this system. Very well done.

@dan3092 3 года назад

Scott the only man alive to fix his Ferrari clutch on the drive in Flip Flops in the rain on his own bar some borrowed muscle.....top work fella

@Ratarossa 3 года назад

cheers Dan , i love to show it done in the plain garage environments without special tools so inspire anyone to have a go

@hennybutabi 3 года назад

You are a legend doing this job alone, without a lift, outside in english weather, on a Ferrari!!! Amazing work!

@Ratarossa 3 года назад

Wow, thanks!

@swieberrr Год назад

Wow Scott! What an amazingly satisfying video. So cool to see that you are not afraid to take stuff apart yourself and the way you do it thoroughly! I don't own a ferrari, but this is great content!

@SurfGreenTelecaster 3 года назад

Really glad to see a video doing major Ferrari work back in your driveway, in flip flops. That’s the true Ratarossa form. 🤌😆

@curvs4me 3 года назад

A tip on a rear main seal cap like that. You would want to leave the plate bolts just slightly loose. This will allow the plate to center on the rear main. It can definitely make a difference in the longevity. It's standard practice on most performance builds. Talking general, not Ferrari.

@AutomotiveEvangelist 3 года назад

Thanks for that tip, it makes complete sense but I probably wouldn't have thought of it and now will keep it in the back of my brain for the next time I do one (which hopefully isn't soon.)

@punkrocktv8229 3 года назад

Who winched when dropped the flywheel on the rear fender..how many days did this take?

@punkrocktv8229 3 года назад

I think i know ehy the clutch lasted longer. He said he used race mode....that would give harder shifts, thus less slipping...less clutch wear. Lesson dont slip the clutch....

@artysanmobile 3 года назад

Ferraris are made for people like you. Fear is half the fight to servicing this car. Obviously a very complex job and you’ve done the required research. One aspect many don’t know is what a joy it is to work on a machine with such flawless fit. The precision actually makes every job easier.

@silverado123 3 года назад

Scott, you do such a great job at explaining everything. I really enjoy your channel. Every video you make keeps our attention through the whole thing.you have a great personality too.

@Ratarossa 3 года назад

thanks buddy thats very kind to say

@chenglo8999 3 года назад

Awesome work! Thanks for sharing. Love to see this job on an F430 someday!

@andyMSH700 3 года назад

Great to see people taking on projects like this.....life is all about the amount of effort you put into it...effort in and results out.

@sotirisbakaimis3276 3 года назад

I admire your courage to do all this by yourself!!!

@chrissax5477 3 года назад

I missed the driveway videos so much! Thanks for going back to the roots! :-)

@bakhteria 3 года назад

i don't even a ferrari, but I gave ur video a thumbs up because anyone that can do a ferrari clutch in their driveway is on another level!

@danielbrown7077 3 года назад

the most bad ass driveway clutch job I have seen by far! and I have changed clutches in car parks out front of race tracks at 3 AM to make racing next day. love the work keep it up

@Ratarossa 3 года назад

THANKS that really means a lot, appreciate the comment

@sidrens5292 3 года назад

I would love to see you do a full clean up of the car - get it back to former glory 🙌🏼

@Ratarossa 3 года назад

i'm thinking about doing that

@Valvey789 3 года назад

Isn't that what he's doing on the Ferrari 512 BBi ?

@mancaveproductions00 3 года назад

It wouldn't be a ratarossa car if its to clean.

@sidrens5292 3 года назад

@@Valvey789 yes, however that’s not the Strad. 😁

@sidrens5292 3 года назад

@@mancaveproductions00 it’s not the Ratarossa - it’s the Strad 🙈

@rashidmarillier7525 3 года назад

lol... one man band replacing sports car clutch in his drive way wearing slip slops. Goes to show anything is possible. Stealership must be having a hissie fit. I love this...

@mftwohill51 2 года назад

Very well presented as you are very talented using the camera to give us all clear crisp shots. So Glad to see, Ferrari use a solid flywheel rather than one of those 2piece flywheels with a solid clutch plate. I am a bit old fashioned , I love the flex to be in the clutch plate, not the flywheel. Thanks for the post, well done.

@Ratarossa 2 года назад

Many thanks!

@jacquesraymond6892 3 года назад

WOWWW!!!!!! I'm amazed looking at you pulling off all these parts to achieve that task. It must be a very expensive job at the Ferrari dealership. Do you realize you are among just a few Ferrari owner's in the world who has the ability to play like that in LA BELLA MECHANICA and to save all that money? You also are for sure the only guy in the world to use a TESTAROSSA as a workbench. CONGRATE AND RESPECT.

@Ratarossa 3 года назад

Thank you buddy

@paperboy7364 3 года назад

Another awesome video Scott! If you can do the clutch on your very lovely Ferrari on the driveway, all driveway mechanics should feel encouraged! Also very much enjoying the BB videos, and envious of the facilities you have to carry the restoration.

@aretardridesmotard6128 3 года назад

I love this so much. I always assumed these were much more complex than they are actually are.

@enochpowellslibrarian5595 3 года назад

I love the way you use your Ferrari's as daily drivers 👍

@Ratarossa 3 года назад

They are cars to be enjoyed and you only live once. I'm not going to my grave regretting I didn't enjoy the cars I worked hard to buy as much as I could. Otherwise its like having a beautiful wife/girlfriend and not 'enjoying' your time with her, only to then die and the watch next man get to enjoy her instead LOL

@enochpowellslibrarian5595 3 года назад

@@Ratarossa I'd be the same m8 👌

@roberthargrave573 3 года назад

As I've never owned a ferrari and never will own one that was a great video everything done to detail congratulations on your work

@slasher9883 3 года назад

Not only did Scott change a Ferrari clutch on his paved driveway in the English weather but he did most of it one handed. Take that so called "Ferrari Techs".!

@leftycarbon 3 года назад

Not sure you'll ever see this comment, but I had to say I enjoyed every minute of this video. Well done!

@Ratarossa 3 года назад

thanks buddy

@XB3Gaming 3 года назад

I love how Ratarossa takes the mysticism out of Ferrari maintenance. Aside from the F1 actuator and tests this doesn't look much harder to do than a Miata clutch.

@328gts1987 3 года назад

impressive to do this alone and on the driveway! Listing to your intro: my car drove 67.000km's on original clutch (F1). It is all in the understanding and feeling how to shift & lift. Put your foot down and keeping it down during shifting (F1) is killing (like in stick-shift car). By lifting the throttle during the shift (upward), the flywheel (& clutch) go down in rpm's (compression reduces the rpm) and by shifting (up-ward) the drivetrain also lowers in rpm's and by this lifting the throttle the clutch "slips" less. However as you have a upgraded ECU as explained in the video, I think that makes all the differance as I have a F430 with same ECU. In short: shift & lift during gear change (=shifting up) helps. Let the ECU shift down as you have lift the throttle to reduce speed and downshifts (during breaking) are done perfectly by ECU. Upgrade the ECU to expand the lifetime on your clutch is key

@grimson 3 года назад

This is inspiring. I don't have anything like a ferrari, but I do have an MR2 and no garage and the clutch is going to need changing soon. I know it can be done, but it's daunting, so good to see someone doing it with a much bigger and heavier transmission!

@thechallengestradale Год назад

I’ve watched this video like 3 times now and feel like I now know how to do this. When I’m done, I feel like I need to pay you because it would have been a LOT harder to do this without your video!

@garybrooks2463 3 года назад

Awesome video! Nice to see you up and back at it. Thanks for all the little details, it makes all the difference. Also big appreciation for the special deals, us do it yourselfers’ find that any little bit of assistance makes all the difference… Love your channel, you’ve open my eyes to the possibility of Ferrari, moments away!! All the best to you, GMB

@turdrocket Год назад

I redid my 612 clutch for 125$. Local shop relined clutch, and ground flywheel and pressure plate. Shifts silky smooth

@reefbloke 3 года назад

Top work!! Who’s tummy rolled over when the old flywheel tapped against the paint/clear coat on the rear wing/fender when Scott was holding the camera one handed .

@malcolmscott4150 3 года назад

You’re amazing Scott, brains and automobile surgeon plus the ability to really drive a Ferrari - great video and content 👍

@Ratarossa 3 года назад

Thanks Malcolm

@michaelkyriacou7026 3 года назад

Nice one Scott, we missed a gritty episode!! 🙂❤️

@burville100 3 года назад

I really miss tinkering on my old 'sh*tbox' cars when I first started out with cars. Great work Scott.

@rogerbarrett9920 3 года назад

Great video with superb narration - I've literally done around 50 clutches a year for all of my working life ( but never on a Ferrari ) and have always worn overalls and proper work shoes. You're a brave man wearing flip flops, as even with the most careful working practices, I've dropped a few things on my feet and been glad of the gear I've had on.

@LouTrottier 3 года назад

My man, you are incredibly brave for tackling that repair in your driveway.

@hpt08 3 года назад

Brilliant work. I often do "crazy stuff" like this with my twenty year old Jag. If you can get the car into a take off/landing style angle, you're probably got the right height for removals of diffs & gear boxes 😁 ... Just be careful with trapped toes, or heads!

@rob_whitney Год назад

Amazing work Scott - I can only imagine how much cash you saved by DIYing it. Proper job 😎

@silver750iL 3 года назад

Great. Just need a 360 now (ideally a cheap one needing a clutch ;)

@motosteggy3980 3 года назад

Scott this is brilliant - The level of detail is what we love, thank you

@mattpovah5952 3 года назад

Very instructional. Any decent shade tree mechanic could follow your instructions here and accomplish a Ferrari clutch replacement - very well done.

@kes7u 3 года назад

Thank you SO much for doing these videos. I can't tell you how much I've learned about my car and how useful these have been. We need to keep as many of these on the road as possible for the NEXT 20 years!

@rousemotorsport 2 года назад

You are a brave man to do this in the driveway. It pains me to see all that stuff all over the paint and the scratches but if you do not care, nor should I. I think your clutch lasted so long because you drove the heck out of it. I am also a Ferrari owner and they are VERY reliable cars if you drive them. I drive mine everyday and I have no problems.

@kevinc31 3 года назад

Love the driveway grind for the repair. Great job!

@miken389 3 года назад

Tks Scott, just snuck in my Superperformance order before the end of the month (to Aus, no less) to take advantage of the free shipping. I've bought from these guys before but the 308 has languished for some months and needs a bit of maintenance so I've loaded up for a couple of future to-do's as well. Had a part query on rear stabiliser bushes which was answered in a flash. Great people to deal with.

@kbrickell4732 3 года назад

the bleed nipple in on the bottom of the clutch actuator unit ,, causes lots of bleed problems really needs to be at the top

@megaman9039 3 года назад

Loved every minute of this video!! More please!!

@philgrimsey3637 3 года назад

I was wary enough doing the clutch on a fwd Rover but damnit, I'd be scared as hell of this.. Good work man. 👍

@windronner1 3 года назад

The rear trans may be more accessible, but it’s your knowledge and experience that makes the scope of difficulty so manageable. Ain’t no such thing as an easy ‘driveway’ clutch job on a Ferrari. Terrific video once again. Cheers Scott 👍

@TheRay280 2 года назад

If I don't understand everything I like your channel. I work at Mercedes and think that changing the clutch on the W906 Sprinter is much better 😂 Greats from south west Germany 👋🏻

@EnglishTurbines 3 года назад

Kudos for doing this video and the clutch...So impressed, I'm not even going to mention your Flip flops..Stuart, and his little doggie were hilarious...🤨😳😳😄😄🇬🇧

@KSL12 3 года назад

I am in admiration of the work you do without a lift. I am spoilt .Well done.

@farewell_to_normalcy9352 3 года назад

Wonderful video once again, Scott! Least I’m not the only person that works on my cars in flip flops 🩴 👍🏻

@flir67man84 3 года назад

these cars are beautifully built..

@rugu6869 3 года назад

You have the best "workbench" using the Ratarossa! Love your content Scott. Keep it coming!

@MachineGunMike Год назад

So legit offer. I’ll pay for you to come to Hawaii if you‘ll come teach me how to change my clutch on my Challenge Stradale. The offer stands!

@randybomar700 3 года назад

Dont own a ferrari but love the channel you lost me when you started to take everything apart im an old guy used to muscle cars .

@glenmeyer5079 3 года назад

Good job Scott! Enjoy your DYI work on the 360. You really need to get a shop with a lift. Hopefully that's in your future.

@georgimihalkov4781 3 года назад

Awesome video! I really missed those complex DIY jobs.

@johnnystoka6625 3 года назад

Good to see a thorough nice clean job .

@stuffa01 7 месяцев назад

WOW, you tear into a Ferrari with more confidence than most guys on a Lawn Mower...

@curvs4me 3 года назад

Gotta be your experience in repairing the F1 hydraulics and your proficiency in driving a manual gearbox. It shifts by itself but you know how it should feel. Not to hold a car on a hill or move forward 5ft at a time in traffic. Wait for a gap, give it a bit of gas and let off quite a bit as soon as it breaks inertia to creep forward. Just a guess, but realistically it should make a big difference. Great work.

@James_Sovereign 3 года назад

And I thought my 996 Turbo was a PITA to work on. Well done mate.

@broomad 3 года назад

Great video Scott - you are really dispelling the myth about Ferraris being difficult to work on. With access to the workshop manual and a suitable diagnostic tool, it looks like anyone could do the work if they are mechanically savy :-)

@Ratarossa 3 года назад

absolutely buddy, its not difficult simple rule is just dont rush the job and double check everything

@mgc1970 3 года назад

Mate.....you are the BOLLOCKS!👍🏻🥃. Outstanding job.... outstanding video.... your knowledge of the inner workings of the Ferrari transmission is epic...AND, the fact that that everything you do is "learn as you go", makes your videos even more enjoyable. Thanks for the incredible content! Please keep it coming!

@gman1003 3 года назад

Amazing that there could be quality 'upgrades' to a car which just by sheer cost should have the finest quality parts available anywhere.

@richarddarsa6353 3 года назад

You are SHOCKINGLY good at this. What a brilliant presentation. Thank you!

@Ratarossa 3 года назад

Wow, thank you!

@richarddarsa6353 3 года назад

@@Ratarossa I saw your Ratarossa at British GP. What a thing!! No roof needed on a day like that!

@MetalTeamster 3 года назад

Yes, I am not a pro mechanic, but I tallied it up recently, and I have done 21 clutch jobs over the last 40 years. A couple semi trucks , a couple medium size trucks, a 1 ton truck , a Fiat X 1/9 , a Lancia Scorpion , a Datsun 280z , a number of Japanese pickup trucks , a Toyota 4x4 , and a Mazda RX - 7. None of those were difficult, and I would not be afraid of this either. Plus..if I got bogged down, which I doubt I would, I could watch your video. Nice job by the way...

@daevidcrawley6936 3 года назад

Genuinely enjoyed that. I'll never own a Ferrari....but now I know how to change a clutch on a 360....love it 😁

@xg5zm 3 года назад

I don't see it been very difficult. BUT thats because I allready saw somebody else doing it. If I did not it will be a different thing 😉😂 Great job nice to see you going back to your origins.

@RobertSmith-qz4zx 3 года назад

love the fact that you clean the parts before you put them back in. So many rebuilders don't

@Voiceofreason99ify 3 года назад

Just love the way you replace all gaskets, o rings etc! Very much my way of working. Only wondered why no thread locker used on clutch flywheel screws.

@Ratarossa 3 года назад

cheers man, yes i used thread lock i thought i showed that in the video ?

@Voiceofreason99ify 3 года назад

@@Ratarossa sorry missed it! Great to see the 360 content again! Best