Тёмный

DIY FPV power filter for under $3 

Подписаться
Просмотров 129 тыс.
% 1 919

If you're flying an FPV RC plane or multirotor and find you have unwanted lines on the video image, you may want to add a power filter to you system.
This video demonstrates how a toroidal inductor and a capacitor can significantly reduce the amount of noise on the power feed to your FPV camera and thereby significantly improve the clarity and quality of the image it generates.
The Soft Ferrite Rings are available from HobbyKing for under $1 a piece (in a 5-pack) and you can pick up the required 470mfd capacitor from any number of sources - or just rip one out of an old computer or TV set. Just make sure that it's rated for at least 16V if you're using a 3S battery or 25V if you're using a 4S. And watch the polarity - it's important.
The enameled copper wire can be picked up in small reels from a hobby store or you can scavenge it for free from an old transformer if you feel so inclined.

Наука

Опубликовано:

 

29 апр 2014

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 272   
@zhenya1343
@zhenya1343 3 года назад
I, for one, love the whiteboard thing. It's awesome to see the theory explained behind the application! Thanks again for this great tutorial!
@SvenOkonomi
@SvenOkonomi 10 лет назад
Ive used these for years, this is one of the best tips you can give for FPV, especially when you are flying on a single battery. The pulsing ESCs induce a really nasty bit of noise.Good on ya, Bruce!
@MyTechWebTV
@MyTechWebTV 10 лет назад
GREAT Bruce! I have learned more about the technical side of this hobby from you than from all other sources combined! Thank you for taking the time to educate once again!
@bgdwiepp
@bgdwiepp 10 лет назад
Great video bruce! I think i remember mentioning inductors in another videos comments! Also, protip; put the toroid in the middle of the piece of wire and wind, it's quicker because you have to pull half the amount of wire through (distance), and you bend the wire strand half as much, fatiguing it less. Plus, half of the toroid is wound when you start the second half, holding it tight allowing you to pull the wire very close to the toroid, and thus more turns! Good video nonetheless!
@midasg1
@midasg1 7 лет назад
I put an LC filter on my VTx power supply line today, and what a difference! I used to have horrible black lines all over the video signal when the throttle was beyond 25 %. But now I get a crystal clear video signal even at full throttle. Thanks a lot for the tip Bruce!
@fokke1037
@fokke1037 8 лет назад
Excellent, this seems to have solved my horizontal line issue on my boscam VTX / Runcam 2 setup. My video was clear, until I increased the throttle... ;-) I tore an old PC PSU apart, used an inductor (with copper wire already attached) and a 16V 2200 capacitor. Many thanks for explaining the background info, it's helped me a lot in partially understanding what we're dealing with here. For those that are wondering: I am running 3S, 12V is coming from my Matek PDB (with 12V BEC) . This is a safer solution in my opinion, for when I choose to run 4S Lipo's later on, I won't have the risk of frying the capacitor.
@louletuga
@louletuga 10 лет назад
"just a short video today folks" ...16 min lol Keep them coming Bruce. Love your white board videos! You explain difficult stuff in a very easy to follow manner! WE WANT MORE WHITE BOARD VIDEOS!!! :)
@servoman11
@servoman11 9 лет назад
You Sir are the best teacher I have ever viewed on The Tube! Thank you for all of your excellent video's.
@beyondfossil
@beyondfossil 9 лет назад
Excellent demonstration with the oscilloscope. Simply excellent!
@hiwayM9
@hiwayM9 10 лет назад
I only recently subscribed... because I only recently discovered your channel... I have lost hours sitting here learning. Bruce, you are by far the most succinct, the most respectful, and the most enjoyable mentor I have ever had in this hobby... and you wouldn't know me if we passed on the street. Bloody damn fine work you do, and I am a better hobbyist for it. *on a related note- I bought a lc common mode filter on advisement when I built my mini 250 and I am glad. *on an unrelated note... I use the Naze... and that is a sweet FC, so based on the comments down there, I am looking forward to your vid on that. You may want to break it into 2 or 3 parts since it can get heady.
@xjet
@xjet 10 лет назад
Why thank you so much for your kind words, they are much appreciated.
@chatwithpete2734
@chatwithpete2734 6 лет назад
Gratitude :) nice work!!!
@The2ndKeepsUsFree
@The2ndKeepsUsFree 10 лет назад
Fantastic information and video Bruce! Great work as always.
@hansleatherby1032
@hansleatherby1032 10 лет назад
Thanks for passing on your knowledge in such an easy way - keep at it Bruce
@EgoIsFlawed
@EgoIsFlawed 8 лет назад
great video, excellent shop presentations, learning electronics has never been easier.
@daretattoo1
@daretattoo1 8 лет назад
Started to LOVE electronics since I started watching your videos. Thanks for your educational and inspirational videos.
@alexadabic
@alexadabic 7 лет назад
thanks man, i was stuck in this filter stuff till i watched your video. Love your videos, keep making them :D
@stephenclute
@stephenclute 7 лет назад
Love the videos, Bruce, been watching since my budget mini-quad build many years ago! I wanted to thank you for this video particularly, as I recently bought the Foxeer Arrow with built in OSD. Adding this style filter cleaned up the noisy video when powered straight from a 4S LiPo, while giving me my battery voltage on the display. Good stuff!!
@tnicod
@tnicod 10 лет назад
Very interesting recap! It took me few years back into the basic electricity field! Thanks very much!
@richa8383
@richa8383 10 лет назад
Bruce I've recently done some experiments with RL, RC and RLC filters at university, so I understand it but wouldnt have thought to use in this application. Nice work. Keep up the great ideas.
@davidringler40
@davidringler40 10 лет назад
bruce by far your videos not only show us how to make equipment and explain how to make and why and what its does and how. that's awesome thank you and GOD BLESS
@MrCottonmouth
@MrCottonmouth 10 лет назад
I really like this video. Very good refresher course. Not only described how to build it, but also how it works. Very good easy to follow explanation. :) 2 thumbs up!
@PauMallol
@PauMallol 10 лет назад
Châpeau Bruce! Precisely considering to get a second power filter from Fatshark to clean up my FPV power lines but your solution is so much more sleek! And I even have the components lying around... :D Thanks, again, for your vids and, especially, your explanations: I like to know why things happen and how the solution works, not just copy the procedures. Happy flying!
@Masterpj555
@Masterpj555 10 лет назад
I really love your videos. I can place your channel right next to the eevblog, ben heck show and dangerous prototypes as one of my favourite electronics related youtube channels. Thank you for doing this!
@renoflash06
@renoflash06 10 лет назад
Bruce, I find these educational videos great to watch. I probably would have paid more attention in my circuits class if the teacher would have talked about RC gear in his lecture. I hope you produce more of these types of videos. I really enjoy the white board videos.
@EhnTeePee
@EhnTeePee 10 лет назад
Also, I watch every minute, you are an excellent orator,sir.
@bigbadalphawolf9330
@bigbadalphawolf9330 7 лет назад
I like watching your videos. You are a great instructor. everything is broken down and you take us step by step explaining everything, which makes learning enjoyable. Thank You. oh, plus you're very funny.
@Walt1119
@Walt1119 10 лет назад
Bruce Thanks so much, especially for the white board schematic and explaination!! My electronics has gotten really rusty, such great fun when you explain it all!!!!! W
@matrixate
@matrixate 6 лет назад
When you know what you're talking about...it makes sense. Good job.
@KiyoCabessa
@KiyoCabessa 9 лет назад
Amazing Tutorial as always :) Thank you Bruce And greetings from Spain
@maikel1707
@maikel1707 8 лет назад
Thank you very much Mr. RC for the perfect explaining about this subject. :)
@keystonerenovation8687
@keystonerenovation8687 9 лет назад
Hi Bruce! I would like to thankyou for the video. I enjoyed watching how you connected it to your QC and i absolutely loved the scientific explanation at the end. At first i was lost but now i am found and it's as clear as day or should i say as clear as a 12v FPV camera mounted with a 400mh conductor and a capacitor :) I'm new to the QC hobby and electronics hobby so i have my new favorite channel. I'll look fwd to seeing more videos like this one! Cheers mate!
@godsgifttocockpit
@godsgifttocockpit 10 лет назад
Thanks again for the video! I only wish our electronics professor would've used some similar practical examples and analogues to explain things. We mostly did just the math around all this without really understanding anything what the circuit actually did or why we needed to bother changing it. Keep up the good work! :)
@fod3er
@fod3er 8 лет назад
That was a really great video to watch, Thanks for sharing your knowledge with us :)
@Hotwire_RCTrix
@Hotwire_RCTrix Год назад
This is a great tutorial. Thank you for your time Bruce. 👍
@peaps
@peaps 10 лет назад
Nice video Bruce. A lot of other sources suggest wrapping servo wire around the core, but on reflection, it makes sense that you'd get more inductance with more turns using thinner wire.
@dave_s_vids
@dave_s_vids 10 лет назад
Great video! Loving the electronics ones, keep them coming please!
@waspmeat
@waspmeat 9 лет назад
What a lesson! Taking me back to Electrical Circuits 101!
@aboldy
@aboldy 9 лет назад
Great article. Really enjoy the way you presented that really made sense. Thanks
@cloudninefpv
@cloudninefpv 10 лет назад
Awesome Bruce!!!! Thanks for the excellent vid
@NormanLedoyen
@NormanLedoyen 10 лет назад
Great video of information Bruce. Please keep it up.
@michealwithington
@michealwithington 7 лет назад
I have been watching your video's since I started in RC and it has been a huge help over the past 3yrs, Also a kiwi. Good Value. Thanks.
@andywonline
@andywonline 10 лет назад
Awesome video, as always. Thanks for sharing.
@heiligcrt
@heiligcrt 10 лет назад
Another great video, thanks Bruce
@jasoneyes01
@jasoneyes01 8 лет назад
Love this guy,, a simple man with fantastic physics mind!
@Jimmehify
@Jimmehify 10 лет назад
Thanks bruce, as always informative and furthering this great hobby! I have no doubt that blackout will include this on their future versions as standard.
@SYNFPVPILOT
@SYNFPVPILOT 10 лет назад
Fantastic video. Thanks Bruce!
@lynx_nz
@lynx_nz 8 лет назад
Awesome video. Thanks for your efforts!
@MrHandsomejackuk
@MrHandsomejackuk 9 лет назад
thanks Bruce.... I wish i never went back to my afternoon lectures drunk.... when i did my HNC electronics....I usually fell asleep.. great information
@TheFarleyGordon
@TheFarleyGordon 10 лет назад
Cheap as beans Bruce just love this stuff Thanks
@timomartens99
@timomartens99 10 лет назад
Super explination! As good as always!
@SWFLJetSkiRiders
@SWFLJetSkiRiders 8 лет назад
Love your videos , keep it up my man
@rick6633
@rick6633 10 лет назад
Always appreciate your explanations. Keep up the good work. Thank you.
@Norminal1
@Norminal1 7 лет назад
Thanks. It's been driving me nuts. I'll give it a go.
@MrCasehatter
@MrCasehatter 10 лет назад
Dang Bruce I do thank you for the education electronics for Dummie's That's me I can trouble shot and change boards but now I'm starting to understand them, I like it, thanks again..!! Hey guys don't forget to go to his web site and donate to keep him alive and helping us...!!! Thanks and keep the education coming it's great..!!
@didgydont
@didgydont 10 лет назад
Thank you for your wonderful explanation
@mattb1967mb
@mattb1967mb 10 лет назад
Dang you're smart... Love your videos !!!! 👍
@zimmy1958
@zimmy1958 10 лет назад
great stuff Bruce. THANKS
@RcBuddy
@RcBuddy 10 лет назад
"Bruce yet another great educational video." indeed +1
@willywgb
@willywgb 10 лет назад
Hi Bruce. Great Video. Would love to see more Electronics Videos. Examples: Buck Converter design, ESC design, Antenna tuning. Cheers Bill
@ME-zu5kg
@ME-zu5kg 10 лет назад
Another educational Video Great going to use it as soon as i get a few ferrite rings. Also the Mice was acting up on the vid as I am sure you said Spasmodic.;)
@N7CX
@N7CX 10 лет назад
excellent demonstration.
@TotallyGlitch
@TotallyGlitch 10 лет назад
As always, thank you Bruce
@RenatsMC1
@RenatsMC1 7 лет назад
I came a cross your videos and you explain similar as my physic teacher easy to understand and interesting to learn ;)
@darrelldixon8248
@darrelldixon8248 7 лет назад
trinity indoor flying
@DENMONKEY
@DENMONKEY 10 лет назад
Excellent video.
@grahamhall1607
@grahamhall1607 8 лет назад
very good just about my level. Enough info to be really useful. Thanks
@icyburger
@icyburger 7 лет назад
awesome vid!
@3deeguy
@3deeguy 8 лет назад
Thank you! I bought a cheap PAL camera and tested it on my NTSC TV (before I received my monitor in the mail) I thought the lines and the tendency of the screen to go black were the result of mixing 60Hz and 50Hz. When I got my monitor and tried to fly FPV I found that the monitor screen would still go black 'until' I pushed the throttle, and I still had lines. I don't have a scope so this video was really helpful.
@fredbutlerfb
@fredbutlerfb 8 лет назад
try to use a non-blue/black screen to avoid this. like the cheap screen the quanum FPV goggles use :)
@grim-upnorth
@grim-upnorth 10 лет назад
Great video, it actually inspired me to go out to the shed and make an inductor... I have a few ferrite torroids and some enamel copper wire. There's just one thing though, you glossed over how to actually "make" the filter. the science and explanation was brilliant, I understood it very well. but it would have been nice to see how you connected up the capacitor (i'm sure there's a right and a wrong way) and then how you would connect this in a real life circuit... still a great video... I actually do like the whiteboard stuff :)
@JavierDiazMn
@JavierDiazMn 10 лет назад
Excellent video, thank you very much
@bigcountryforever
@bigcountryforever 10 лет назад
what a great video very well explained :-)
@snaprollinpitts
@snaprollinpitts 9 лет назад
thanks Bruce, I love when you show us the electronics and the theory behind it, great vid!!! a quick question about coil saturation, can you use a small board inductor as a pick up, and with a scope see the spikes or if it's saturated it should come up to a level and stop moving? what do you think? thanks again for your engineering expertise!!!
@PHILSWINGIT
@PHILSWINGIT 6 лет назад
Hi Bruce love your vids but this one for me is a winner thanks mate
@pixelpusher3589
@pixelpusher3589 7 лет назад
thanks Bruce.......the great explainer
@baccus61
@baccus61 9 лет назад
Great info and very well explained. Love ya work. :-)
@1TheBurner99
@1TheBurner99 10 лет назад
Very very cool and helpful.
@bobot021070
@bobot021070 9 лет назад
That is kinda Big help for a guy like me Whos into this hobby. Big thanks to you and hope u have more helping vids to come. Thanks Daddy white BEARD. 😁😁👍👍👍
@Hoverbot1TV
@Hoverbot1TV 9 лет назад
Thanks Bruce making 1 right now,
@lolmadmaxlol
@lolmadmaxlol 10 лет назад
Great video as usual :) Thanks for all your instructions, explainations and hints. But one short question. If i have a 5V FPV camera should I put the regulator before or after this LC-lowpass filter?
@ahmedashraf8294
@ahmedashraf8294 6 лет назад
excellent ! you are a legend sir
@MrAlvaromendes
@MrAlvaromendes 9 лет назад
realy nice your explanation, take my like!
@oman636
@oman636 8 лет назад
mate your a legend love the videos , keep up the swagger
@alexisrazon6239
@alexisrazon6239 10 лет назад
As always another awesome, educational video! I am almost confident in building one even with my zero electronics knowledge. Two questions though... what are the resistors for and what are their ratings? I want to get this right the first time. Thanks!
@SmokinMesa
@SmokinMesa 7 лет назад
Cheers Bruce. Every day's a school day
@joacimwennerberg8310
@joacimwennerberg8310 10 лет назад
Thanks. Great video :-)
@RakishRc
@RakishRc 3 года назад
I had the same problem with my 1500mw video transmitter I use for my rc car fpv with 1.2ghz video. I had the tx connected to lipo I use for my rc esc to power up via balance adapter. On high throttle I'd loose the video with black lines. I simply used a separate 3s lipo to power the tx and haven't had any problems yet.
@Flash1940
@Flash1940 10 лет назад
Good job Bruce....Everybody needs to know about an L..C filter. Maybe another winding right on top of the first...then you may haqve been able to use a slightly smaller cap. Saving some space,,,,maybe. I have some of those from Amidon that have different mixes for upper frequencies.....I have a homebrew converter that converts from 50MHZ to 14MHZ. Used a Grid Dip meter to line it all up.
@flymrc77
@flymrc77 10 лет назад
Clever man.
@PhilLucasVLOGs
@PhilLucasVLOGs 8 лет назад
Very informative video. Thanks for putting it up. I understand that putting a capacitor in parallel effectively grounds the peaks in voltage due to the motors need for pulsed supply. Have you tried either putting the capacitor in series or and additional capacitor in series (in addition to the parallel)?
@OverdoseCule
@OverdoseCule 8 лет назад
Thanks a lot for this video
@TeamIcarusRC
@TeamIcarusRC 10 лет назад
Very cool!
@CorieRC
@CorieRC 10 лет назад
amazing. Thank you!!!
@zorglev
@zorglev 10 лет назад
Great video. A question was asked about stripping the lacquer from the enameled wire. I find furniture stripper containing methylene chloride works very well. Just a tiny dab is necessary. Won't work on epoxy.
@RCbattler
@RCbattler 9 лет назад
Bruce I just wound one toroid (Hobbyking one 16mm dim). I was able to wind the wire 31 times. I am using 32 AWG. I think i used ~ 70cm of enameled copper wire. It is interesting that i am getting only 120uH. Do you have any suggestions on what wire to use, or what could i be doing wrong? Thanks.
@ahmedagbabiaka
@ahmedagbabiaka 9 лет назад
another excellent one Bruce. Question if you run your camera off a 12v BEC and vtx off a 5v BEC, do you use one LC Filter before both BECs or do you run an LC filter after each BEC?
@JeffInflyt
@JeffInflyt 8 лет назад
Brilliant explanation as always! I don't know much about electronics but in this example, the fpv cam is drawing power after the motors. If the cam was connected to the battery first before any load, would that have fixed the problem also?
@c0p0ut
@c0p0ut 8 лет назад
I love your videos. They have helped me so much in this hobby. Keep them coming! I just have one question. At 2:20 you mention the copper wire thickness is unknown but it will be added to the video. I'm having a hard time finding it. Can you tell me what thickness you used, and/or what range is best to use? I am about to place an enameled copper wire order and they are asking what thickness I need. Thank you!
@simonnaughton2272
@simonnaughton2272 10 лет назад
Awesome video ***** Sadly I'm only learning this electronics stuff as an adult, but better late that never right? Thanks again.
@williamstewart1269
@williamstewart1269 7 лет назад
Do you connect ferrite ring and cap in the vtx power feed line, cap across and ring inline, add cap across esc leads also? Your diagrams are great for us visual learners. Thx from the States
@TeodorD
@TeodorD 8 лет назад
Hello Bruce, love your videos .. keep it up. Was wondering does the transmitter need to have power filtration, or does that have it already on board? I know it can depend but just as a general rule:P Thanks ;)
@kericole5802
@kericole5802 9 лет назад
First I want to say thanks Mr bruice for all the awesome videos.. Very inspired... Part 1 Now I went to a electronic wholesalers and found everything except the 2a resistor because they where measured in ohms... Maybe I'm that noobie but even the employees had no idea how to help...can you give me more info on the resistor part/type... Part 2 If I run a 4s battery with this setup and the 12v camera and tx can I just run a resistor to cover the tx and camera for both 3s and 4s applications. this is an open question thanks for reading.. :)
@spirulinedfpv6792
@spirulinedfpv6792 9 лет назад
Excellent. To make more windings, can I use just the red (+) cable and not the black one ? Also... Should it be better done before the camera, or before the Vtx ? Or Both ? Cheers.