DIY porch | FREE STANDING PATIO COVER | material from HOME DEPOT

Подписаться 8 тыс.

Просмотров 234 тыс.

50% 1

I built a patio cover for the first time, I got all material from home depot. Total for everything was $3000. It's a big PATIO cover for being the first one I built, 25x16 ft 6x6 post 2x8 rafters 6x10 beam 3 inch screws, 3\4 sleeve anchors and strong tie post base
here are some tools I use for this build .
amzn.to/3uFoyGA 72in level
amzn.to/3RmRw6S drill set
amzn.to/47YMi6O circular saw
amzn.to/3sWSpty string level to do a slope for water
amzn.to/48bSDvT tape measure 25'
amzn.to/3Tp9iIp framing hammer
amzn.to/3uOSPTj square 12"
amzn.to/47RNzNl Ear Protection
amzn.to/3Nh6qte work gloves
amzn.to/46SqVTN construction pencil
Construí una cubierta para patio por primera vez, obtuve todo el material de Home Depot. El total de todo fue $3000. Es una cubierta de PATIO grande por ser la primera que construí, poste de 25x16 pies, 6x6, vigas de 2x8, viga de 6x10, tornillos de 3 pulgadas, anclajes de manga de 3\4 y una base de poste de amarre resistente.

Развлечения

Опубликовано:

30 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 154

@alfredo2824 10 месяцев назад

Always put the nut on the bolt then hammer it to the concrete that way you don't mess up the threads

@Redblocksvideos 10 месяцев назад

thank you that’s great advice 👍🏾

@MrFaststang 8 месяцев назад

Most anchor bolts are designed to where you won't mess up threads when hammering down

@advert1984801 5 месяцев назад

Thats a false statement, you will mushroom the top if you strike it to much or wrong on any anchor, always put the nut to where its flush to top of anchor@MrFaststang

@hectorcisneros1376 5 месяцев назад

Negative. Do not hammer. Your gun has hammer mode with no spin setting. Bolt has a dimple on threaded end. Set nut and use hammer gun to drive in bolt

@titdtv2400 Месяц назад

Dude, very very solid tip. My dumb ass would have never thought of that and I’ve done 5 jobs w posts lmao

@DavidLee-b9k 17 дней назад

Miller Richard Thompson Paul Taylor Jeffrey

@syd8699 6 дней назад

Jackson David Robert Jason Henry Roger

@andydinh7863 10 месяцев назад

Nicely done but I would love my patio cover to attract tightly to the house so when rain I walking out without getting wet

@Redblocksvideos 10 месяцев назад

There are two ways to have this done, one would be to see one side of the patio cover on top of the roof and the other will be called lean in patio cover. When it is lean into the house is attached to the side of your home and this way it will cover you from the rain or the sun.

@JoshR512 4 месяца назад

@@RedblocksvideosI’m trying to build one, with permit. House already has a flat roof addition to the back. There’s a pergola at the moment nailed to the fascia, but it looks ghetto. Do you think it’s possible to build one a bit higher than a flat roof , so it over laps maybe a foot? Pitch the rain away. Thanks !!

@Redblocksvideos 4 месяца назад

@@JoshR512 yes, it’s possible to make it higher. Just check with the city for the permit

@SonyaMoore-l8k 22 дня назад

Harris Angela Robinson Richard Thompson Christopher

@JoanWanda-l5t 10 дней назад

Garcia Eric Martinez Shirley Young Timothy

@mikeinna2814 11 часов назад

How did you anchor the rafters to the beams? Great work by the way.

@EthelWest-f4o 10 дней назад

Smith Sarah Williams Robert Brown Frank

@johnbiknobarrington1403 16 дней назад

Gonzalez Eric Robinson Maria Harris Amy

@strategy400 День назад

No mask, cutting treated lumber

@RittikaHatun-c8p 20 дней назад

Hall Nancy Young Ronald Anderson Karen

@WereDiamonds 10 месяцев назад

Is there a slope on the roof? I didn't see one, if there is how did you make that heppen?

@Redblocksvideos 10 месяцев назад

That’s a great question. In my county the minimum slope that this construction built has to have is a quarter of an inch for every foot minimum , this cover has 3” slope because it is 16 feet long. i used a string line level for this.

@OneAcer 9 месяцев назад

Great job! What height did you cut the posts at? Doing mine this weekend similar to yours, free-standing with the high side of the roof just above the house to keep the area under the patio cover dry. I like how this design maintains easy access to service the gutters.

@Redblocksvideos 9 месяцев назад

I don’t remember the height of the post, I honestly didn’t measure how high they were going to be. They are the same high as the roof, and from there I did a slope of a quarter of an inch for every foot with my string level. I left a link for the string level from Amazon. If you want to purchase it it’s about three dollars. The actual party cover was about 14 to 15 inches above the roof total counting beam, and the Raptors going across. Hopefully this makes sense.

@OneAcer 8 месяцев назад

@@Redblocksvideos Oh yes this makes total sense, thank you! I installed the 3 posts near my house first to get the height of the beam on the posts correct then installed the remaining 3 posts and beam away from the house. I used your string level idea too, thanks. My rafter length is 12 feet, have not decided if I will slope to quarter of an inch or higher because I'm concerned of rain water not falling fast enough down the metal panels. Maybe I will go 3/8 of an inch and use galvanized roofing screws that have the rubber washer and caulk them all.

@leanderyoung1119 4 месяца назад

Do you have a listing of parts, dimensions and plans?

@Redblocksvideos 4 месяца назад

I do not have a complete list, but I did use 2 x 6 regular number by 16 and 6 x 10 x 14 beams, and 6 x 6 post, 6 x 6 house brackets and 3/4 of an inch by six anchor bolt, also bracket and a tie tie bracket for a 6 x 6 beam, I also use 4 x 8 half-inch plywood for the roof and six by one facia board

@spotonndiyvids6065 10 месяцев назад

What size post beams are those I can’t find them that length came out beautiful 😻

@Redblocksvideos 10 месяцев назад

if you’re looking for than at home depot, you won’t be able to find it in stock. they are spacial order head over to customer service and place the order. 6x10x14 this is the size for the beams and for the post i use 6x6x8. 👍🏾

@yorvelisfalcon651 5 месяцев назад

@@Redblocksvideos What type of wood did you use?

@Redblocksvideos 5 месяцев назад

@@yorvelisfalcon651 pressure treated 6x6 for posts , 6x10 for beam and normal 2x6 for rafters

@JuanCoolDad 2 месяца назад

Are the black simpson T brackets the only thing holding the cross beams to the posts or is there other hardware?

@Redblocksvideos 2 месяца назад

i did a few 3in screws before the T bracket

@JuanCoolDad 2 месяца назад

@Redblocksvideos That makes sense, thank you!

@salp541 7 месяцев назад

How did you prevent this from wobbling? I find when I don’t bury the post in concrete or tie into the house these structures always move a bit…?

@Redblocksvideos 7 месяцев назад

I really don’t have a problem with that, probably because it’s pretty big and he has six post instead of four. It does move a little bit if push on purpose, otherwise it’s just fine.

@DavidSanchez-365 2 месяца назад

Why don’t you show the cuts for the slope?

@Redblocksvideos 2 месяца назад

I forgot to record , I’ve forgot to record a few steps like a hole to pour the cement and also part the cement and other things too. i’m gonna build another one soon and I’m gonna make sure to record every step of the way from start to finish.

@ray6808 10 месяцев назад

Great job. What is the square footage? And what's the estimate of all the materials for this project? I like to do something similar on my back porch with a screen.

@Redblocksvideos 10 месяцев назад

thank you 😊. it was 400 sf, just on material was $3k i got everything from home depot

@FaithNoFear00 5 месяцев назад

This one is interesting because you chose to separate the house from the patio. Was it just preference that you didn't adjoin the roof of the house with the patio? I mean you wouldn't be worried weather or not rain or high wind and rain could plummet in between the two? It's still a great job but gutsy, lol.

@ApexxJimmy 5 месяцев назад

I think he would need a permit and whatnot, if he attached it to the house, regardless of square footage.

@FaithNoFear00 5 месяцев назад

@ApexxJimmy Yeah that came to mind. As a mortgage-free homeowner here in my state, we don't have to have to have any permits. As long as it's code.

@Redblocksvideos 5 месяцев назад

I didn't want to complicate the construction of the patio, tying it to the house would be more steps to follow. Just like that it was faster and easier.

@FaithNoFear00 5 месяцев назад

@Redblocksllc Yeah that's what I figured. Keep it simple right.💪👍🏼

@JuanMartinez-nz4vx 4 месяца назад

I actually like the idea of not disturbing the house roof, my house is only a year old so I’m weary about messing with a new roof. I did notice the rain gutter so that should help with most rain water coming through the separation. I’ve seen quite a few videos and after seeing this video I’m pretty much going through with this set up.

@lizardman1303 7 месяцев назад

Looks good but been having so much trouble these kind of post they been splitting apart so much

@Redblocksvideos 7 месяцев назад

what type of post wood do you use? I used the pressure-treated and I chose them. I didn’t let this store close for me, that usually keep out the worst ones.

@Timotheoreviews 3 месяца назад

Do you get snow in your place? Just wondering if this could handle snow loads, which I assume it does

@Redblocksvideos 3 месяца назад

it’s does but not as much, i believe it could possibly hold 6- 12 inches of snow not sure to be honest

@thisisatest6495 3 месяца назад

I'm wanting to do something like this for my patio which is 33' x 9', that means I'll have to get different lengths 6x10 beams and posts be distanced unevenly. Anyone know if that'll affect the weight distribution?

@Redblocksvideos 3 месяца назад

you can use the same size post but yes you’ll definitely different beam size you coil decide it in 11’ section and get 6x10x12

@jlacson74 4 месяца назад

This is probably a dumb question. Does free standing means it is not attached to the house?

@Redblocksvideos 4 месяца назад

yes that’s exactly what it means

@provokn 2 месяца назад

How deep are the footers for the post and how much concrete did it take to fill them?

@Redblocksvideos 2 месяца назад

They were about 2 feet deep and I don’t really remember how much concrete I got. I believe I use 2 to 3 60lbs bags for each post.

@lore4357 5 месяцев назад

Hello, in your cost does that include the brick pavers?

@Redblocksvideos 5 месяцев назад

nope just the patio cover

@DIYHome-9 10 месяцев назад

Good quality❤

@KB-sm6pj 4 месяца назад

This is a great job! Great video! How much of overhang did you do? It looks like you put it just a little bit past the Gutter so when you walk out, they’ll be no dripping in between that crack is that right? Is that how you did it?

@Redblocksvideos 4 месяца назад

thank you, it’s 2 feet both sides and yes that was the plan

@jose9899 6 месяцев назад

very nice. How much did you spend on the supplies for this build ? I want to build the same for my backyard

@Redblocksvideos 6 месяцев назад

it’s was about for $3000

@Grandpa_RLP Месяц назад

Does your patio cover stop even with gutters edge of the house or go over the gutter to edge of house? I want free standing to get more height but I also don't want rain to get between house and patio cover. How far do you think you can over hang house without interfering with future roofing replacement?

@Redblocksvideos Месяц назад

this patio cover is high enough so it doesn’t interfere with the house roof and goes 2 feet past the gutters. I don’t remember the exact measurement, but I did make it where it’s not too high that when the wind blows it doesn’t bring the water with it. I did it this way so I could walk outside and not get wet.

@Grandpa_RLP Месяц назад

@@Redblocksvideos that is what we want too. Thanks

@harvortiz4756 4 месяца назад

You’re missing a lot of steps in your video. This shoddy project won’t last 2 years.

@Redblocksvideos 4 месяца назад

it already has two years, still in a good shape

@alejandrovalencia7971 2 месяца назад

Of course it is, it’s a Timelapse summary of a build not a “how to” video….. also nobady is building something in 17 minutes so of course it’s not going to have everything

@razajamali2801 2 месяца назад

Great work. Was the floor made of concrete or did you dig hole and put concrete to hold the posts. If dug hole, how deep and wide did you pour concrete?

@Redblocksvideos 2 месяца назад

thank you I did a hole about 2 feet deep and it was about 12 inches of diameter

@razajamali2801 2 месяца назад

Thanks @Redblocksvideos . Shingles on roof ?

@jhoff1970 9 месяцев назад

How did you fasten the rafters?

@Redblocksvideos 9 месяцев назад

I used 3” screws in an angle

@FaithNoFear00 5 месяцев назад

@@Redblocksvideos I was wondering that also because I didn't see you do it.

@RicDog120 3 месяца назад

I thought I was the notches. But just to verify. Did you bird mouth the rafters?

@snicklesnockle7263 4 месяца назад

This house has no yard. Dystopian.

@Redblocksvideos 4 месяца назад

it does probably not as big as you would like yours.

@jocktheglide 8 месяцев назад

can you hang out up there say two people just sit and enjoy the top view?

@Redblocksvideos 8 месяцев назад

not a bad idea haha

@stevenhicks815 4 месяца назад

How do you fasten rafters to beam where you over hung the from past beam?? Thanks for any help

@Redblocksvideos 4 месяца назад

I did a small notch to the Rafters so they can see flat on the on the beams, and then ice crew both size of the rafters 3 inch screws

@stevenhicks815 4 месяца назад

@@Redblocksvideos awesome thank you. Is that patio all free standing not attached to house anywhere correct

@rileycrain5784 2 месяца назад

How was the permit process for this?

@Redblocksvideos 2 месяца назад

no permits on this for me

@UberWagen 7 месяцев назад

Glad to see you used hex bolts instead of the little 3 1/2" screws and the 'finishing' washers that are fake nuts. The finish solution from simpson is like 3x as much compared to using 6" bolts that will be stronger anyway.

@Redblocksvideos 7 месяцев назад

the simpson it’s just for looks 😊

@armandomtecu575 3 месяца назад

How yoi nailed the wood above the beams

@Redblocksvideos 3 месяца назад

i used 3” deck screws

@AdrianRodriguez-ik4eh 3 месяца назад

I'm trying to build aa 18 x 18 with max height of 8ft. What would you recommend

@Redblocksvideos 3 месяца назад

you just use 4x4 for post and maybe 4x6 for a beam

@AdrianRodriguez-ik4eh 3 месяца назад

@@Redblocksvideos due to a door being in the way of walkway would need to do a 4 foot over hang from on end of the beams would that be an issue if i used 12 foot beams

@AdrianRodriguez-ik4eh 3 месяца назад

@@Redblocksvideos due to a door being in the way of walkway would need to do a 4 foot over hang from on end of the beams would that be an issue if i used 12 foot beams

@Tierone1337 10 месяцев назад

What is patio vover

@Redblocksvideos 10 месяцев назад

PATIO COVER. A structure with open or glazed walls that is used for recreational, outdoor living purposes associated with a dwelling unit

@kevingp12 4 месяца назад

Are those plans running across the beams notched slightly?

@Redblocksvideos 4 месяца назад

do you mean the rafter 2x6 ? yes

@kevingp12 4 месяца назад

@@Redblocksvideos yes ok!

@tonyduran9956 4 месяца назад

Una pregunta. Si lo mueves se mueve mucho o no ?

@Redblocksvideos 4 месяца назад

muy poco , brazos que tienen en 45 en los postes ayuda.

@MegaBlizzard911 5 месяцев назад

Searched through all the comments rough estimate on the build costs

@Redblocksvideos 5 месяцев назад

it was $3500

@MegaBlizzard911 5 месяцев назад

@@Redblocksvideos thank you for the reply!

@ajyoung4530 5 месяцев назад

12:55 these were put on backwards.

@Redblocksvideos 5 месяцев назад

The T strap?

@trahuynh_usa 4 месяца назад

Did you screw down all the rafter across the beams?

@Redblocksvideos 4 месяца назад

yes i did 3in screws

@mp-sv2cp 4 месяца назад

Did you?

@TannerRoberts-k2i 7 месяцев назад

What size post beams are those I can’t find them that length came out beautiful

@Redblocksvideos 7 месяцев назад

they are pressure-treated 6 x 6 x 8. They were a special order at Home Depot. If you go to the pro section you can order any size you like they do not have it in stock.

@rodolfovalle120 2 месяца назад

Yo acabo de hacer un porch de 28 x 12 pero se muebe poquito es normal?? Tiene 8 postes grandes que puedo hacer para que sea mas resistente ayuda porfavor

@Redblocksvideos 2 месяца назад

si copiaste la manera que lo hizo igual que el que yo hice si tiene poquito juego peor es normal, no sea cae. en casa poste de vería tener una madera que corra del poste a la viga en grado 45. eso hace que se sienta más estable

@rodolfovalle120 2 месяца назад

Oh grasias ya estaba asustado grasias por responder

@robser2324 5 месяцев назад

Did you have to get city permits?

@Redblocksvideos 5 месяцев назад

no i didn’t but it would be a bad idea to check if you need one in your location

@AdrianRodriguez-ik4eh 8 месяцев назад

Where do you attach the string for the slope. Do you attach it to the post on each end and and then mark for the cuts?

@Redblocksvideos 8 месяцев назад

yes, i first cut all the post from one side of the cover and have them level, after a run my string from the top of the post to the other side and marked it

@chentez1 6 месяцев назад

Cuanto mas o menos el precio de material?

@Redblocksvideos 6 месяцев назад

cuando lo hice fue como $3000-$3200.

@betuldaglar3469 2 месяца назад

The cost how much

@Redblocksvideos 2 месяца назад

it was $3000 in materials

@Unknown-yc3nc 8 месяцев назад

how much was for the cross beams?

@Redblocksvideos 8 месяцев назад

I can’t remember how much he was but for all the material was $3000. This is a 28 feet long patio cover. probably was around $300 per beam 6x10x14

@abelperez2466 6 месяцев назад

what sizes is this pergola?

@Redblocksvideos 6 месяцев назад

27’x16’

@johnnychingas7573 8 месяцев назад

How far apart are the posts?

@Redblocksvideos 8 месяцев назад

11ft. it’s 26 ft long with 2ft overhang around

@roberto6870 6 месяцев назад

Did you stain those posts?

@Redblocksvideos 6 месяцев назад

no i did it, that’s just the color of the pressure treated wood

@roberto6870 5 месяцев назад

@@Redblocksvideos do you know the item number on those posts from homedepot?

@plataurieta9168 8 месяцев назад

Excelente trabajo muy profesional, donde están localizados ??

@Redblocksvideos 8 месяцев назад

gracias, en salem oregon!

@plataurieta9168 8 месяцев назад

Pásame tu información amigo

@roberto6870 6 месяцев назад

Does the rain go through the gap where house roof is and patio?

@Redblocksvideos 6 месяцев назад

only when it is raining with a lot of wind

@roberto6870 5 месяцев назад

@@Redblocksvideos also what’s the slope?

@Redblocksvideos 5 месяцев назад

1/2 for every foot

@yashuwbyisrael2324 5 месяцев назад

You said quarter inch for every foot in another reply?

@Redblocksvideos 5 месяцев назад

@@yashuwbyisrael2324 both works just fine 1/4 or 1/2

@MarkoJ-k7u 6 месяцев назад

what type of wood did you use? pressure treated pine or ceder?

@Redblocksvideos 6 месяцев назад

pressure treated 6x6 for post and 6x 10 beam

@MarkoJ-k7u 5 месяцев назад

@@Redblocksvideos did you paint or seal it?

@roberto6870 5 месяцев назад

@@MarkoJ-k7uthat’s what I thought also pressure treated usually more lighter looks stained

@Redblocksvideos 5 месяцев назад

i didn’t do any painting nor sealing, but it wouldn’t be a bad a idea to seal the rafters, the ones i use are normal 2x6

@MarkoJ-k7u 5 месяцев назад

@@roberto6870 thank you

@marcossalcido8823 7 месяцев назад

Cuanto de profundidad el footing??

@Redblocksvideos 7 месяцев назад

24 pulgadas

@marcossalcido8823 7 месяцев назад

Muchas gracias

@jesusvaldez2869 5 месяцев назад

Que buen jale se aventaron. Cuánto cuesta un trabajo así ?

@Redblocksvideos 5 месяцев назад

Gracias si yo lo hiciera para alguien yo cobraría unos $8000-$7000 pero me salió $3500 en materiales

@gensanchez9535 4 месяца назад

@@Redblocksvideos Excelente trabajo !! Muchachos : este trabajo el costo $$$ de $7,000 / $8,000 tambien incluye ? lo del Piso los Pavers ?

@Redblocksvideos 3 месяца назад

@@gensanchez9535 no, los pavers alguien más se los aventó. creo cobraron por día

@Roberto72722 5 месяцев назад

What distance did you put the rafters spacing?

@Redblocksvideos 5 месяцев назад

16”

@fergferguson7370 3 месяца назад

Overkill for home and neighborhood.