DIY Robot Liquor Dispenser | Amazing Homemade Alcohol Dispenser | Brilliant DIY Whiskey Dispenser

Подписаться 264 тыс.

Просмотров 100 тыс.

50% 1

#AlcoholDispenser #DIYWhiskeyDispenser #LiquorDispenserDIY
Disclaimer: All parts and fittings that come into contact with liquor were cleaned, disinfected, and of stainless steel and lead free brass materials.
Hello and Thanks for watching. In this video I will show how to make an amazing Robot Liquor Dispenser. This cool and unique idea is not difficult to make and it looks amazing. Below is a list of all the parts. Please let me know if you have any questions or suggestions in the comments below. Like and subscribe if you enjoyed the video. Thanks for your support.
FOR SPONSORSHIPS AND BUSINESS INQUIRIES CONTACT:
infoaxcreates@gmail.com
DISCLAIMER:
All product links are affiliate links.
VIDEO IS STRICTLY FOR ENTERTAINMENT ONLY
TOOLS AND PARTS USED IN THE VIDEO:
Milwaukee Coordless Drill www.amazon.com...
Dewalt 4 1/2 Grinder www.amazon.com...
Hobart Handler 140 Welding Machine www.amazon.com...
Drill Bits www.amazon.com...
FILMING EQUIPMENT:
Camera Cannon Rebel T7i www.amazon.com...
Camera Tripod www.amazon.com...
Mac External Drive www.amazon.com...
FITTINGS THAT MAKE UP THE BODY
FITTING QUANTITY
1) 3/4" NPT Chicago Coupler 1
2) 3/4" Carbon Steel Tee 3
3) 3/4" carbon Steel Street 45 ELL 1
4) 3/4" Standard 45 Elbow 3
5) 3/4" Brass Hex Head Plug 1
6) 3/4" Brass Square Head Plug 1
7) 3/4" Carbon Steel 90 Street Elbow 4
8) 3/4" Standard Carbon Steel 90 ELL 1
9) 3/4" Carbon Steel Cross 1
10) 3/4" Brass Close Nipples 9 ( can substitute with carbon steel)
11) 1" x 3/4" Carbon Steel Bushings 2 ( can substitute with stainless)
12) 2" x 1" Brass Bell Reducer 2 ( can substitute with 2" x 3/4" and eliminate 1" x 3/4" bushings)
13) 2" x 1 1/2" Carbon Steel Bushings 2
FITTINGS IN CONTACT WITH LIQUOR
FITTING QUANTITY
1) 1" x 3/4" Stainless Steel Bell Reducer 1
2) 3/4" Stainless Steel Tee 1
3) 3/4" x 1/4" Stainless Steel Bushing 1
4) 3/4" Stainless Steel Close Nipple 2 ( one end capped on one nipple, 10 Gauge Sheet Metal used to make cap.)
5) 1/4" Stainless Steel Compression x 1/4 MPT Elbow 1
(can substitute with a TEE and connect vent to it if unable to weld)
6) 1/4" Stainless Steel Compression 1
x 1/4" MPT adapter
7) 1/4" Lead Free Brass Nipple 1 (can substitute with stainless steel nipple)
8) 1/4" Lead Free Ball Valve 1 (can substitute with stainless valve)
9) 1/4" Lead Free Barb x 1/4" MPT Adapter 1 (can substitute with stainless steel adapter)
10) 1/4 Stainless Steel Tube Approximately 26" needed
11) 3/4" x 1/4" Lead Free Brass Bussing 1( can substitute with stainless bushing)
12) 1/4" lead free Socket Hex Head Plug. 1(braced/welded to 3/4" x 1/4" Bushing to prevent flow into the arm)
13) 1" x 3/16" Rubber O-Ring Gasket 2
BASE
1) 6 1/2" x 11 1/4" 10 Gauge Stainless Steel Sheet Metal
2) 6 1/2" x 11 1/4" x 3/4" Wood Base
3) 3/4" Flat Washer or any washer with diameter of approximately 1 5/8" diameter, Need 2 (welded to 2" x 1 1/2" Bushing)
4) 1/4" Flat Washer, Need 2 (welded to 3/4" washer)
5) 1/4" x 1" Hex Head Bolts with nuts and flat washers, Need 2 (welded to 1/4" and 3/4" washers)
1/4" Hex Socket Button Head bolts and washers 6

Опубликовано:

27 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 127

@craftstest 3 года назад

Amazing super super super like good luck 😍❤️😍❤️😍

@axcreates_official 3 года назад

Thanks. 👍

@MakeItMetal 4 года назад

My favourite drink dispensed by the coolest of creations! got my sub buddy!

@axcreates_official 4 года назад

Thank you for the positive comment! 😀

@diycreationsvet4878 4 года назад

I like it the way he made it i might do another one. I build mines out of bronse, epoxy resin and gun casings.

@eyjolfurthorleifsson7467 4 года назад

Beautiful work ❤️ Very genius. Thank you for sharing

@axcreates_official 4 года назад

Eyjolfur Thorleifsson Thank you very much for your support. 👍👍

@jtklop 4 года назад

This was very well done. Love the idea for bring in air

@axcreates_official 4 года назад

Thank you and thanks for watching.

@jtklop 4 года назад

DIY Creations please do!

@axcreates_official 4 года назад

@DIY Creations Thank you.

@crazyeyes1533 3 года назад

thanks for the vid! I want to make one for a christmas gift!

@axcreates_official 3 года назад

👍Thank you.

@carldyke5725 3 года назад

Appreciate the "Parts List". 👍🏼 Overall the best "DIY" video I've watched on making a whiskey dispenser. Although, I don't weld/solder.

@axcreates_official 3 года назад

Hi, thank you for your comment. What you can do is replace the stainless tee ( liquor side tee) with a stainless cross and add a stainless valve between the carbon steel tee and stainless cross. Then you can do all threaded and use tubing and compression fittings for the vent. Just like I did in my other dispenser video. Check out the link below. That’s what I’m referring to. I’m sure you can find it cheaper. This is not an affiliate link. Hope this helps. 👍 DERNORD Stainless Steel Ball Valve - 0.75 Inch NPT Threa... www.amazon.com/dp/B07MJ73VKW/ref=cm_sw_r_sms_api_glc_fabc_-pc4FbH9ARAZG?_encoding=UTF8&psc=1

@julianreese6021 3 года назад

i guess im randomly asking but does someone know of a way to get back into an instagram account? I stupidly lost the password. I would appreciate any assistance you can offer me.

@leoantonio5477 3 года назад

@Julian Reese instablaster ;)

@julianreese6021 3 года назад

@Leo Antonio I really appreciate your reply. I got to the site through google and im trying it out atm. Takes quite some time so I will reply here later with my results.

@julianreese6021 3 года назад

@Leo Antonio It worked and I finally got access to my account again. I am so happy:D Thanks so much, you saved my account :D

@tanakornnasaro1567 2 года назад

สนใจสั่งอุปกรณ์ครับ

@thegiant9035 3 года назад

Genius!!

@axcreates_official 3 года назад

Thank you.

@CristianArequipa-w6m 6 месяцев назад

Podría decir los nombres de los accesorios que utilizo por favor..?? Me fascinó mucho quisiera intentarlo.. Gracias de ante mano..!!

@axcreates_official 5 месяцев назад

Toda informacion en la descripcion del video.

@marcelocarvalho7274 3 года назад

Quero um desse

@MrNovruz 4 года назад

Nice

@axcreates_official 4 года назад

Thank you 😀

@JorgeAlberto-oy3de 3 года назад

O cara , pra fazer isso tem que ser dono de fabrica de conexões tubolar

@danielsolorio8215 4 года назад

How much would you sale this for?

@lesliestraw4699 3 года назад

Great build just very expensive on the parts list, my guess £150

@swishersmith1875 8 месяцев назад

Tell me you work in the store room without telling me you work in the store room

@Chevyguyscott 2 года назад

Pretty Cool, But lost me at Golden Knights ;)

@axcreates_official 2 года назад

👍

@florent1239 3 года назад

Bonjour, es ce que vous auriez un site ou on peu trouver toute ses pièces svp ? ☺️

@sarojdhungana8239 4 года назад

Can i get the list of parts that are used in this project 🙄

@axcreates_official 4 года назад

Absolutely, here it is. And as you can see, many of the fittings can be substituted. I used what I had available at the time and that's the reason I mix-matched the fittings. Thank you for watching. FITTINGS THAT MAKE UP THE BODY FITTING QUANTITY 1) 3/4" NPT Chicago Coupler 1 2) 3/4" Carbon Steel Tee 3 3) 3/4" carbon Steel Street 45 ELL 1 4) 3/4" Standard 45 Elbow 3 5) 3/4" Brass Hex Head Plug 1 6) 3/4" Brass Square Head Plug 1 7) 3/4" Carbon Steel 90 Street Elbow 4 8) 3/4" Standard Carbon Steel 90 ELL 1 9) 3/4" Carbon Steel Cross 1 10) 3/4" Brass Close Nipples 9 ( can substitute with carbon steel) 11) 1" x 3/4" Carbon Steel Bushings 2 ( can substitute with stainless) 12) 2" x 1" Brass Bell Reducer 2 ( can substitute with 2" x 3/4" and eliminate 1" x 3/4" bushings) 13) 2" x 1 1/2" Carbon Steel Bushings 2 FITTINGS IN CONTACT WITH LIQUOR FITTING QUANTITY 1) 1" x 3/4" Stainless Steel Bell Reducer 1 2) 3/4" Stainless Steel Tee 1 3) 3/4" x 1/4" Stainless Steel Bushing 1 4) 3/4" Stainless Steel Close Nipple 2 ( one end capped on one nipple, 10 Gauge Sheet Metal used to make cap.) 5) 1/4" Stainless Steel Compression x 1/4 MPT Elbow 1 (can substitute with a TEE and connect vent to it if unable to weld) 6) 1/4" Stainless Steel Compression 1 x 1/4" MPT adapter 7) 1/4" Lead Free Brass Nipple 1 (can substitute with stainless steel nipple) 8) 1/4" Lead Free Ball Valve 1 (can substitute with stainless valve) 9) 1/4" Lead Free Barb x 1/4" MPT Adapter 1 (can substitute with stainless steel adapter) 10) 1/4 Stainless Steel Tube Approximately 26" needed 11) 3/4" x 1/4" Lead Free Brass Bussing 1( can substitute with stainless bushing) 12) 1/4" lead free Socket Hex Head Plug. 1(braced/welded to 3/4" x 1/4" Bushing to prevent flow into the arm) 13) 1" x 3/16" Rubber O-Ring Gasket 2 BASE 1) 6 1/2" x 11 1/4" 10 Gauge Stainless Steel Sheet Metal 2) 6 1/2" x 11 1/4" x 3/4" Wood Base 3) 3/4" Flat Washer or any washer with diameter of approximately 1 5/8" diameter, Need 2 (welded to 2" x 1 1/2" Bushing) 4) 1/4" Flat Washer, Need 2 (welded to 3/4" washer) 5) 1/4" x 1" Hex Head Bolts with nuts and flat washers, Need 2 (welded to 1/4" and 3/4" washers) 1/4" Hex Socket Button Head bolts and washers 6

@sarojdhungana8239 4 года назад

@@axcreates_official Thank you ❤️

@diycreationsvet4878 4 года назад

I like it the way he made it i might do another one. I build mines out of bronse, epoxy resin and gun casings.

@dreadly2010 3 года назад

have you noticed any issue with rubber seals deteriorating because of the alcohol?

@axcreates_official 3 года назад

I haven’t, make sure you select the correct o-ring seal. Nitrile and Neoprene is what I have used.

@dreadly2010 3 года назад

@@axcreates_official Thanks for the quick reply!

@nathanwilson7453 3 года назад

Whats the part called that you screw the bottle into?

@axcreates_official 3 года назад

It is a 3/4" x 1" Bell reducer. This is an affiliate link. Hope this helps. www.amazon.com/dp/B008E338QI/ref=as_sl_pc_qf_sp_asin_til?tag=alexpalominos-20&linkCode=w00&linkId=526d92254918a42341ac17758dded833&creativeASIN=B008E338QI

@faustorodriguez532 2 года назад

Hello can i get a list of the materials. Its amazing thank you in advance

@axcreates_official 2 года назад

Thank you. The list is in the video’s description.

@cain2bad 4 года назад

Nice job. I’ve made my own version but it leaks out my air tube. Would that be because it’s not long enough? It doesn’t go passed the bottle. Thanks for the inspiration.

@axcreates_official 4 года назад

Thank you for watching and your support. Yes. I’m sure that’s the problem. It needs to be higher than the bottle. This one in particular is about 3” pass the bottle and works just fine. I did run into the same problem when I made the very first one, but just made the vent longer and it solved the problem. Hope this helps. 👍

@cain2bad 4 года назад

AX Creates Thanks. I’ll keep you posted when I get me a longer piece.

@cain2bad 4 года назад

@@axcreates_official I did think that also but I’ll send you some pic’s tomorrow bro. I appreciate you for sure

@axcreates_official 4 года назад

No problem. Thanks again for your support.

@Jguirguis1979 3 года назад

Hello.....what stops the liquid from flowing into left arm? Is it just gravity?

@axcreates_official 3 года назад

Hi, the fitting you see @ 6:16 is a 3/4” x 1/4” brass bushing with small 1/4” threaded plug. Which I then threaded into the 3/4” 90. The 1/4” plug is what prevents fluid from going into the arm. This plug only needs to be threaded into the bushing, but as you can see in the video, I welded it. Just some Teflon will do the job, no need to welded. Hope this helps. Thanks for watching and let me know if you have other questions.

@Jguirguis1979 3 года назад

Also, not much if a welder...is there a close nipple with one end closed available for purchase?

@axcreates_official 3 года назад

@@Jguirguis1979 I don’t believe they’re made already capped. However, I’m looking into how the two dispensers I made can be done without any welding. That will be a new video.

@cristianjuarez8257 3 года назад

Donde consigo las piezas. ?

@axcreates_official 3 года назад

Puedes encontrar la mayoría de las piezas en una tienda de plomería.

@mykingischrist167 3 года назад

How did you cut a 3/4 circle into that thick of sheet metal?

@axcreates_official 3 года назад

Manual Metal hole punch, hydraulic metal hole punch, or just a grinder and cut wheel will do.

@mykingischrist167 3 года назад

@@axcreates_official Thanks man! I don't have access to any of that, so I decided to use 3/4 lead free brass check valve instead. I'm also going to use a 1/4 stainless steel check valve for the arm.

@axcreates_official 3 года назад

@@mykingischrist167 Thats a great idea! A ball valve will also work. You can even reduce down to a smaller valve (1/4” or 3/8” with a couple bushings. Hope it works out. 👍

@mykingischrist167 3 года назад

Is there another option if we can't weld a cap on the close nipple? I did see the way to make vent without welding. Thanks man! 3/4" Stainless Steel Close Nipple 2 ( one end capped on one nipple, 10 Gauge Sheet Metal used to make cap.)

@axcreates_official 3 года назад

Glad the idea of the threaded vent helped. Also, I found that just a straight vent with no bends works better. And about the cap on the close nipple, let me see what else I can come up with and I will definitely get back with you. Thanks for your support. 👍

@mykingischrist167 3 года назад

@@axcreates_official Awesome, I appreciate it! Subbed

@axcreates_official 3 года назад

@@mykingischrist167 Thank you for your support. 🙏👍

@axcreates_official 3 года назад

Hi, you can use a check valve or a ball valve in between. The ball valve would just make it a little longer because you'd have to use two short nipples. Check out this link. This is not an affiliate link, just want to show you what you can possibly use.Also, I am sure you can find it cheaper. Hope this helps. www.amazon.com/Stainless-Steel-Valve-Female-Thread/dp/B07PTNQ4WW/ref=sr_1_20_sspa?dchild=1&keywords=3%2F4+one+way+stainless+valve+male+ends&qid=1606408298&sr=8-20-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzVjdTVFhGN1FMQ0RRJmVuY3J5cHRlZElkPUExMDI4ODM0MUNOSUU5UEJJWEhCVyZlbmNyeXB0ZWRBZElkPUEwNTU0NDk4MjBQT1RVTlYySlEyMiZ3aWRnZXROYW1lPXNwX210ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU=

@biracialbabes 3 года назад

So awesome!

@axcreates_official 3 года назад

Thank you.

@raimundocoata3492 3 года назад

Vc fazer para vende

@axcreates_official 3 года назад

Não no momento. Obrigado.

@nickbender7920 3 года назад

You did an amazing job! This is so awesome!! About how much does it cost in parts?

@axcreates_official 3 года назад

Thank you. The cost for all the parts is about $140 -160. It was a fun project.

@nickbender7920 3 года назад

Sweet thanks for the reply. This inspired me. I’m definitely going to attempt this!!

@axcreates_official 3 года назад

You’re welcome. Let me know if you have questions. 👍

@christilley9444 3 года назад

This is awesome! Can you give a list of exact parts by chance?

@axcreates_official 3 года назад

@@christilley9444 Thank you. You’ll find the list of parts in the description.

@R1CAN1 4 года назад

Do you sell them?

@danielsolorio8215 4 года назад

How much? I know the parts and work cost money. Still interested

@gunnarbiker 4 года назад

@ 3:47 what the heck is that fitting called?!?

@axcreates_official 4 года назад

It’s called a 3/4-Inch Male NPT Chicago Coupler or 3/4 Male NPT quarter-turn claw type hose quick coupling used for air and water.

@diycreationsvet4878 4 года назад

I like it the way he made it i might do another one. I build mines out of bronse, epoxy resin and gun casings.

@cesarescutia6185 3 года назад

Perdón desee rrobot

@methot 3 года назад

Very nice work. I'm planning on building one very soon and your work inspired me a lot. Two questions: would the constant contact of alcohol on metal eventually change its taste? Maybe there would be a way to thread a flexible vinyl tube inside the iron pipes? Also, how easy is it to clean it, say you'd want to put some other alcohol in there? Thanks and great work once again!

@axcreates_official 3 года назад

Thank you. Yes, you can feed a small diameter vinyl tube through the pipe fittings. That’s a good idea. But to answer your questions, stainless and copper are often used in the construction of whiskey/alcohol stills so I don’t think it should affect taste. The cleaning is fairly easy, dish soap and hot water does the job. Hope this helps. Thank you for watching.

@matthews2943 2 года назад

Where did you get all the parts? I’m thinking about making one.. these are super cool

@joshgleghorn260 3 года назад

Where did you source the stainless steel tube from?

@axcreates_official 3 года назад

Local plumbing store/supply house.

@CoreyDS40 3 года назад

How much for all the parts?

@axcreates_official 3 года назад

around $140 us dollars.

@mat-bh 3 года назад

Só no brasil q não existe tubo galvanizado. É praticamente impossivel achar essas conexões por aqui. Ainda mais pessoa p fazer rosca na ponta do tubo.

@axcreates_official 3 года назад

Os acessórios são de aço inoxidável. É uma pena que esses acessórios não estejam disponíveis no Brasil.

@mat-bh 3 года назад

@@axcreates_official steel pipes are deprecated in brasil at least 3 decades. Here we only use pvc or copper pipes. Just in a few rare situations the galvanized pipes are used.

@axcreates_official 3 года назад

Isso é lamentável. Eu ficaria feliz em enviar-lhe um no futuro, se possível.

@ravneetgill86 3 года назад

Is it necessary to use brass nipples in between the joints or I can use regular nipples. Thanks great work 👍

@axcreates_official 3 года назад

No, it is not. It is just for looks. As you can see, the liquid doesn’t flow through the body. Just from the back tee to the gun(1/4” valve). Thanks for watching.

@ravneetgill86 3 года назад

@@axcreates_official awesome thanks

@Pupkis86 2 года назад

Классный диспансер, НО ЕБАТЬ какой дорогой, дороже самого напитка в два раза.

@jessikamat1 2 года назад

Pardon me but you are going to make people sick with this design.

@raybans8712 3 года назад

Surely the only reason you could dislike this video is jealousy...... or a deep hatred of whiskey 🥃

@axcreates_official 3 года назад

👍👍

@funf7774 8 месяцев назад

Hi, kann ich eine Liste aller benötigten Teile bekommen? Gerne kaufe ich auch den kompletten Bausatz! LG

@axcreates_official 8 месяцев назад

It’s in the video’s description.

@dom5775 4 года назад

Good job ax creates

@diycreationsvet4878 4 года назад

I like it the way he made it i might do another one. I build mines out of bronse, epoxy resin and gun casings.

@hywhook 3 года назад

lo mesclaste con cola.... por dios, que desperdicio.

@davidvarney7353 3 года назад

Very expensive for all those fittings but still very cool

@axcreates_official 3 года назад

Thank you.

@jrrican5770 3 года назад

I wish it didn’t have any soldered or welded areas so everyone could make one, everything else was awesome

@axcreates_official 3 года назад

Will make one soon where no welding is required!👍

@geronmos9618 4 года назад

Great idea!!! Perfect work!

@axcreates_official 4 года назад

Thank you.

@diycreationsvet4878 4 года назад

I like it the way he made it i might do another one. I build mines out of bronse, epoxy resin and gun casings.

@cesarescutia6185 3 года назад

Encuanto mesaleuno depedos rrobot

@axcreates_official 3 года назад

No los hago para vender en este momento. Gracias.

@durgeshrai8136 3 года назад

So satisfying bro 🙌 Great job

@axcreates_official 3 года назад

Thank you. 👍

@PUKKA18 4 года назад

Very nice work. Is it important to weld on the thin pipe, wich goes straight up into the air ?

@axcreates_official 4 года назад

Hi! Thank you for watching. Yes, It is important because it allows air to enter to get better flow. No, it doesn’t have to be welded. It can be threaded. However, you’d have to replace the T fitting with a cross fitting like I did in this video and use all threaded fittings. Hope this helps. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-aBIc7LcMdPg.html

@PUKKA18 4 года назад

AX Creates Thanks for the quick answer. Do you it is s problem, that the drinks floats through the metal pipes ? I want to built something like this, but am scared that it could be unhealthy.

@axcreates_official 4 года назад

Lukas Quast You should be fine if you make it out of stainless steel like I did and clean it once in a while like everything else. Stainless steel is often used in food processing and facilities like dairies and breweries. And to be honest, I think the cross will work better than the T because you won’t have that loop where fluid will just sit there after you pour a drink. You can eliminate that loop if you use a cross.

@paulben4758 Год назад

Good

@axcreates_official Год назад

Thanks

@raimundocoata3492 3 года назад

Ficou muito bom

@axcreates_official 3 года назад

Obrigado. 👍

@silverman2112 3 года назад

Nice Idea and great work! Where did you get all Pipes and angle ? ^^

@axcreates_official 3 года назад

Most of the fittings and pipe you can find at your local hardware and plumbing supply store. Amazon carries many of the fittings as well. You’ll find the list of all the parts in the description. Hope this helps. Thank you for watching.