DIY Router table part 2 - the fence

Подписаться 7 тыс.

Просмотров 24 тыс.

50% 1

In this second part of my three part series on building a router table attached to a cabinet saw, I will take you through how I built the fence and with a touch of inception, I use the fence to build the fence! :D
Parts used in this series:
Router - amzn.to/39B8vj2
Router plate - amzn.to/3MnSgqv
Levelers - amzn.to/3MnlYMl
Dust port - amzn.to/3nUKI4B
t-track (KM tools) - kmtools.com/co...
t-track (Amazon) - amzn.to/41dsZ6i
Stop block - kmtools.com/pr...
Some of my tools:
Router - amzn.to/39B8vj2
Trim router - amzn.to/3xdowUH
Pocket hole jig - amzn.to/3DxARVG
Woodpeckers stainless steel squares - www.woodpeck.c...
Cabinet Saw (Similar to mine) - amzn.to/43rz0P0
Jig Saw - amzn.to/3j0Eom8
Circular Saw - amzn.to/3v9Nrab
Brad point bits - amzn.to/3K6rnmK and amzn.to/3x7uAie
Right angle clamps - amzn.to/3uP9zX8
Router Template guide bushing: amzn.to/3DcHCOE
Round nose router bit: amzn.to/3AWTsty
Countersink drill bit - amzn.to/3UmxOs8
Flush trim bit (KM tools) - kmtools.com/co...

Хобби

Опубликовано:

30 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 19

@TomsBackyardWorkshop 5 месяцев назад

I dont like that stop block for one reason. To move it out of the way you have to completely remove it.

@bijan4727 14 дней назад

Hello. This was an excellent and very elucidated presentation. I learned a lot. You should make one for router stand and installing a lifter. I followed very well but at the end when you installed the movable fence I got lost. How do you move the fence and lock it ? Please explain. Thanks

@altorres4760 Год назад

Good job on the router fence!! I want to make that one but thinking about adding inserts behind the adjustable fence faces to use it as a jointer.

@sydswaine3627 9 месяцев назад

Same here!

@jimsjacob 9 месяцев назад

The “Skim cut on the table saw…”. I’m wondering how to do that since the side against the fence is unknown with possible squeeze out of glue, etc?? I don’t have a Jointer to true sides so I’m wondering how that is accomplished. Cut one side, flip it and cut the other?

@carterscustomrods 6 месяцев назад

Nicely done! @1:55 What table saw is that? I ask because im curious as to whether that riving knife is stock, DIY, or aftermarket?

@mwreyf1 7 месяцев назад

Why restrict your bit opening to just 2 1/8"? Seems at least 2 5/8" would have left you with the option to run raised panel bits if you ever so choosed to.

@MMMS75 6 месяцев назад

Excited to be working on a router table next! I see you’ve got the triton tra001, told my wife that’s what I want for my bday/father’s day this year! Can’t wait!

@RedcarWW 6 месяцев назад

Just came across you vid searching for a way to integrate a router table with my Delta/Rockwell contractor saw. I bought a Delta's T3 fence system to replace the original fence. Just wondering why you wouldn't use the existing table saw fence?

@macsworkshop 6 месяцев назад

I guess I could have built into the existing fence but it would have been hard to incorporate dust collection into it then

@leanwoodworks 9 месяцев назад

Good Lord.. That’s a Great Makita Miter Saw. I was just reminded of how big a foot print those older saws have. Good vid kid!

@macsworkshop 9 месяцев назад

Yea is is a good saw but you’re right, I’d love one that doesn’t have such a big footprint, the bench I made for it has to be too wide to fit it

@leanwoodworks 9 месяцев назад

@@macsworkshop Yep that’s why I waited 10 years to build my Paulk Workbench’s yes 10 years!! I have a LS 1019 now. Snagged a deal on Craigslist 475 American still in box!! LS is 365 MM From the Front of fence to the wall. FESTOOL is 360. Speaking of FESTOOL we have had issues in America with FESTOOL motors burning up. I don’t think they covered everything as far as 50hz to 60hz conversion. My CT VAC is fine but it has a switch you can change it from European to USA however there’s a pretty large array of electronics under the hood in that vac.

@SteveA58 Год назад

Your channel found me recently. Love the Router Table & Fence! Looking forward to the dust collection.

@macsworkshop Год назад

Thanks Steve 😊 I’m in the middle of editing it but it’s been bad weather here so I haven’t been able to record an intro/outro because of the rain I’ll hopefully have it done within a week

@SteveA58 Год назад

@@macsworkshop I do have a question. What is the clear plastic you use when doing glue-ups? I have never seen anyone else use something like it.

@macsworkshop Год назад

It’s just a roll of plastic I picked up from a craft store we have in New Zealand called spotlight A lot of woodworkers use a formica bench to do glue ups on as the glue doesn’t stick to formica, but I don’t have space for that so it’s just a roll of plastic 😆