No video :(

DIY Shoe Rack | Build It | Ask This Old House

Подписаться 2,1 млн

Просмотров 170 тыс.

50% 1

Ask This Old House general contractor Tom Silva and host Kevin O’Connor build a combination bench/shoe rack out of fir decking.
SUBSCRIBE to This Old House: bit.ly/Subscrib...
Time: 4-5 hours
Cost: $150
Skill Level: Moderate
Tools:
Miter saw [amzn.to/2KneNCF]
Table saw [amzn.to/2KpFzub]
Sanding block [amzn.to/3cBzPJN]
Drill driver [amzn.to/2RZfZQV]
Pocket hole jig [amzn.to/3avZLoL]
Shopping List:
1x4” fir porch decking [www.homedepot....]
2x2” baluster stock [www.homedepot....]
Sandpaper [amzn.to/3cFBv4Q]
Wood glue [amzn.to/3bydBIC]
Pocket screws [amzn.to/34YTAbK]
Spray-on high gloss urethane [amzn.to/2RYEg9A]
Spray-on satin urethane [amzn.to/2VKiyY0]
Steps for building a shoe rack:
1. Start by cutting all the pieces of the fir decking. To ensure each repetitive cut has the same dimension, Tom recommends using the stop on the miter saw. Cut pieces for the rails and slats that will eventually make up the shelving for the shoe rack.
2. Using a table saw, cut dados into the rails and rabbets on both ends of each slat.
3. Sand all the pieces individually before assembling using a sanding block.
4. Insert the slats into the rails. Add filler pieces the thickness of the dado and the same width as the slates into the dado to fill in the holes between the slats.
5. Once the positioning of the slats in the dados are correct, pull each filler piece out individually and apply wood glue to the joint. Repeat this process for the rail on the other side of the shelf.
6. Pull out the slats and sand the filler pieces in the rail smooth.
7. Apply wood glue to the slats and push them into the rails.
8. Clamp everything together and allow the glue to dry.
9. Assemble the shelves using pocket screws.
10. Put the boards together for the top. Place the shelves and the base on top of the shelves to determine the right location for the top. Secure the base to the top using more pocket screws. The top does not require wood glue or any additional connections.
11. Apply a finish to the shoe rack. In the video, Tom and Kevin applied a high gloss urethane.
12. Allow the coat to dry and then apply a second coat. Repeat this process for the third coat. For the second and third coat, apply the satin finish.
Resources:
For lumber, Tom and Kevin used fir porch decking, which can be found at home centers.
To assemble the shoe rack, Tom and Kevin used a combination of wood glue, which is made by Gorilla Glue [amzn.to/3bydBIC] (www.gorillatough.com) and pocket hole screws using a Kreg K4 jig [amzn.to/3avZLoL] (www.kregtool.c....
For the finish, Tom applied a combination of Clear Satin and High Gloss Water-Based Interior Polyurethane Spray Paint [amzn.to/2RYEg9A], which is manufactured by Varathane (www.rustoleum.....
Build It:
This Old House general contractor Tom Silva, This Old House host Kevin O’Connor, and special guests including Jimmy DiResta, take you through step-by-step DIY projects in this popular video series. From end-tables to cutting boards to wine racks to chicken coops and more, learn how to build from the best pros in the game. Segments include mention of all tools and materials needed to get the job done.
Looking for more step by step guidance on how to complete projects around the house? Join This Old House Insider to stream over 1,000 episodes commercial-free.
bit.ly/2GPiYbH
Plus, download our app for streaming full episodes to your connected TV, phone or tablet:
bit.ly/34RYEP5
Follow This Old House and Ask This Old House:
Facebook: bit.ly/ThisOldH...
Twitter: bit.ly/ThisOldH...
bit.ly/AskTOHTw...
Pinterest: bit.ly/ThisOldH...
Instagram: bit.ly/ThisOldH...
Watch the full episode:
www.thisoldhou...
DIY Shoe Rack | Build It | Ask This Old House
/ thisoldhouse

Опубликовано:

28 апр 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 94

@jk_22 6 месяцев назад

I'm impressed with your ability to pick out straight lumber at a home center

@persontimr5052 4 года назад

This is insane work for a shoe rack. Framing a house seems easier. But gosh darn nice end product.

@kevinremsen5627 4 года назад

Beautiful piece. The banter between the guys cracks me up.

@djxxxplicit 4 года назад

Tommy is the best! Wished he was my uncle teaching me the tricks of the trade.

@M4st3r0fN0n3 4 года назад

legend says that to this day, rich still owns that pair of holy socks

@electricalron 4 года назад

Tom is a gift to the American fabric.

@faghihimohammad 4 года назад

3:37 using ear protection while hand sanding means you consider yourself to be powerful like a power tool ! :D

@lennykrapitz4794 4 года назад

Kevin is most definitely a tool.

@txshah78 4 года назад

Yes

@JArias2012 4 года назад

Tommy is a master! I was amazed by it!

@debiallen4053 2 года назад

Have been looking for a good plan for 2 days. One that doesnt take a lot of room. Wow! This is perfect. I should know I can always count on Tommy. My go too for everything. To heck with scrolling. I know where to look every time . Thanks again Tommy. I love it. Will be building tomorrow for myself and another for my sis. Perfect!

@crmcbrideww 4 года назад

Good for carrying a lot of weight I see 🤣🤣🤣

@larrymoore6640 4 года назад

Richard gave it the real test... lol. Nice job guys.

@TheBritishPatriot 4 года назад

Tom makes everything look so easy, the only problem is you need years of experience, the right tools, wood and make the right measurements beforehand. What was his wife thinking when she bought that cheap thing!

@TheBritishPatriot 4 года назад

@Jbog07 yeah, probably just a conversation starter for show purposes.

@steveide2062 5 месяцев назад

I was looking to build a shoe rack-bench when I found this video. So I decided to use this design, however, I didn’t want the pocket hole screws to be visible, so used a combination of wood dowels and pocket hole screws. I used dowels to assemble all the pieces that make up the sides and legs. Then I doweled and glued all the top bench-top boards together to eliminate flexing between boards and need for a center brace underneath. I made the slatted shelves in the same manner as Tom did. After sanding all the various parts, I used pocket hole screws to assemble it all together. It came out great, however there is a slight amount of side to side (shearing) movement that could become problematic over time with heavy use. This is something I realized was lacking in Toms design, so I plan to address it in some manner. A lot of people made comments about not having a table saw/fancy tools to use when woodworking. Videos such as these are intended for those who are into basic modern woodworking and the first and most important tool one must have when woodworking is a table saw. I started out 35 years ago with a small 8” $150 tabletop saw and have made quite a number of projects with it.

@deanslegos1990 4 года назад

Right on time, I'm going to do this tomorrow night

@deanslegos1990 3 года назад

11 months later and I'm still planning on doing this tomorrow 🤣 I actually built a hall tree last year instead

@htcinfinity 3 года назад

@@deanslegos1990 That's the story for most of my projects.

@charleshartman8036 4 года назад

Don’t need it. Gonna watch it.

@tranlee5622 3 года назад

Reefdd

@heathdetweilerRealtor 3 года назад

That’s why I’m here. 😂🤪

@sethromusic 2 года назад

They made that look way easier than it actually is 😂

@BB-uz4tc 4 года назад

Nice fellas! Stay handsome. Love the NYC Peaky Blinders

@hujohnny7785 Год назад

Great product, easy to clean -worked out great !

@johnroberts9560 4 года назад

Hi TOH , that's a nice shoe rack that you built there tommy , nice job !!! 👍😊🛠

@maxgarcia7056 2 года назад

Very nice, but what are your dimensions and rabbit and dado widths? I didn't hear any in your video. Can you PLEASE reply. Thanks

@josephmelvin9882 4 года назад

Terrific project and top shelf! Just curious why aren't you more specific about specs and dimensions?

@SportsFan0027 4 года назад

Nice appearance from Richard 😂😂

@JoseHernandez-tc1kl 4 года назад

Wow I’m going to try it I don’t have all time he fancy tools but I think that I can come close .

@esbreidenbach 2 года назад

Couple of other things to take into consideration after having built this: 1) the width of the shelf rails is listed as 1 and 3/4 inches, while the legs are listed as 2x2's. However, the true width of the 2x2s is probably 1.5 x 1.5, so you may want to rip those shelf rails to match the width of the 2x2's. You also may want to make the length of the slats 0.5 inches longer than the width of the end rails, to account for the width of the 1/4 inch rabbits on each end of the slats. 2) If you assemble as shown in the video, you may have a hard time with attaching the base to the top because the shelf spacing is 6 just inches and might not allow enough room for your drill. It is probably easier to attach the top after you attach the top rails, but before you attach the shelves.

@crmcbrideww 4 года назад

I miss Norm Abram

@justinwoods240 4 года назад

I built one a couple of weeks ago

@RaineyPowerTraining 4 года назад

Can you make videos for the layman too? I don't think most people have table saws for the notches and so on

@GrahamDIY 4 года назад

Good old Tommy. He might have slowed down a little (haven’t we all) but he’s still got skills on the table saw All these guys are great 👍 I’m in the uk 🇬🇧 and I wear my This Old House hooded top with pride. Great show.

@studiogerk Месяц назад

Was it really easier to do the fake mortise and tenon? I dunno, seemed like a lot of fiddly prep work ... for me this is a job for a floating tenon or dowels or similar.

@VictorRodriguez-dn9vk 3 года назад

There’s always that, one guy! 8:38

@courteousanalyzer 2 года назад

Holy moly!

@esbreidenbach 2 года назад

Love the shoe rack, and the video and I am in the middle of building it. It does require a table saw and chop saw, which seems reasonable to have for a do-it-your-selfer. The only thing which they skip which seems critical is how to make the little 1/4" by 1/4" by 1" "blocks" to fill in the dado. Trying to make those on a table saw seems dangerous unless there is some trick I am not aware of. Noticed that the measurements on the top boards are posted wrong (18 inches, but the bench is 33 " wide. But more concerning is that the lenght of some of the slats differs between what is visible on the "cut list" showing on the web site and what you get if you click on "download cut list". And to add to the confusion, the clips of Tommy cutting some of the items in the video does not match either! I am using the "downloaded cut list" as it seems to match up with the final dimensions the best.

@txshah78 4 года назад

Better than magic

@anthonycantoni7823 3 года назад

Tony C. Would like to build this project, where's the cut list?

@1sttigertiger426 4 года назад

Tommy's got mad skilz!

@hayalbert Год назад

everytime best solution

@joshsavage1093 3 года назад

That's alot of work for 6 pairs of shoes

@dwoodog 3 года назад

I wanna make something like this. Mine would need to be able to accommodate gum boots.

@greglebeau9477 3 года назад

WHAT IS THE SPACING OF THE SHELF SLATS

@XPStartupSound 4 года назад

Kevin: So no glue in those slats? Tom: NOT YET

@dabeamer42 4 года назад

of course...give the (boring) sanding job to Kevin. :-)

@dabeamer42 4 года назад

@Joe Kinchicken LOL!!

@draffter4055 3 года назад

At what point in this video did you give any dimensions?

@JohnJones-it3us 4 года назад

Just curious why there doesn’t seem to be any concern for wood movement in fastening the top to the frame. Thanks.

@cdee2456 3 года назад

its not glued, only screwed, shouldnt be a problem no?

@User556q 2 года назад

because you exagerate the wood movement. in a small piece like that it wont be alot of movement

@jmfia2391 4 года назад

"It's good for holding a lot of weight too." 😭😭🤣🤣🤣

@benbuckley2738 4 года назад

Why a gloss finish then satin?

@lonewolf3564 3 года назад

It takes the glossiness down a notch

@johnfithian-franks8276 4 года назад

Hi, Can I get one of those usfull items that do my sading for me, but where do you store him when he is not in use?.

@rushsh10me 4 года назад

I miss Norm

@nicholasstone1826 3 года назад

I imagine Tom's wife getting tired of asking for a shoe rack and so she buys the cheapest thing she can cause she knows it'll drive him nuts.

@dangkolache 4 года назад

fake mortise/tenons and pocket holes, matthias is screaming right now

@plasmac9 4 года назад

It's a good thing Norm wasn't around the shop that day.

@TheLovelyMissBeans 3 года назад

Don't be woodworking snobs. This is obviously mesnt for beginners. Everyone has to start somewhere.

@muchobaratodop 7 месяцев назад

It works.

@tedanzigg 4 года назад

A bit convoluted to say the least, could have made two in the time.

@tylercorbin8073 4 года назад

6:00 why so quiet?

@persontimr5052 4 года назад

Tyler Corbin because it took 40 hours...

@tylercorbin8073 4 года назад

Daniel Daniel Still not a reason to sound like that

@hubbell627 3 года назад

How to make things with equipment no one has.

@RC51Rod Год назад

Bahahah! I just bought that piece of crap online shoe rack! I here looking to make my own!

@gerryryan9666 2 года назад

how long is table top boards

@justinwoods240 4 года назад

I'm surprised you let tommy go to the store for this project plus where was his mask

@yangchangjiang 3 года назад

Maybe it is easier to use epoxy wood filler to fill the dado.

@AstridmauMaulidin 3 года назад

Amazing tool amazing skill

@heathdetweilerRealtor 3 года назад

I wonder what that blurry glue is. 😂

@renswic 4 года назад

"you on a budget" 'uh ya' *proceeds to use a $200,000 plus shop and paid assistant* Love it though.

@justinwoods240 4 года назад

I’m not quite sure but I think this was filmed before 2014 I did a little research and I’m not sure why I was but I have clues that I hope aren’t right

@debandmike3380 2 года назад

Funny how Kevin always gets stuck doing the sanding

@randomsanwhich2 4 года назад

Most DIYers won’t have a table saw

@Popcorncedar 4 года назад

I really wish you would push your local lumber yard a bit more. The whole “home center” thing is tiresome.

@400voltas4 4 года назад

The reason they do it because Home centers are much more accessible. People know where they are. Easy to spot one. but local lumber yards are hard to find sometime

@Jwwwwwww300 4 года назад

Home Depot is a sponsor of This Old House that's why.

@RWW1980 4 года назад

What watch is Kevin wearing?

@meelamiela Год назад

Could I diy this out of an old bookshelf? Like the basic composite wood kind they sell in stores?

@foxfiresidechats5227 4 года назад

Hahaha Richard

@exmember1607 4 года назад

So much work! I’d rather spend the $10 and get one at Walmart

@jameskappel 4 года назад

wonder what are the people going to do in the trade industry for 😷 N95 Respirator Face Mask like Tommy had on?

@lonewolf3564 3 года назад

If you go onto a website called 1,000 bulbs.com they sell PPE equipment and have n95 respirators/make that are CDC approved and the same masks doctors use. Yes, I know it's weird that a light bulb website company would have PPE equipment but I guess they caught on to the market need, but be paired to pay a high price. They charge $120 for a box of 20 and will only sell them in quantities of at least 20. wow that's not exactly cheap It's still a reasonable price to be well protected. Think about how much more a hospital stay would cost.