No video :(

DIY STEERING WHEEL ARDUINO LEONARDO WITH FORCE FEEDBACK

Подписаться 2,2 тыс.

Просмотров 73 тыс.

50% 1

DIY STEERING WHEEL ARDUINO LEONARDO WITH FORCE FEEDBACK
DIY Materials :
1. PVC Sheet Size.10 x 20 cm Thick 5 mm
2. Pillow Block Bearing Type.KFL-08
3. Bolt + Nut + Ring M4 x 1.5 cm
4. Fully Thread Rod Size.M6 x 20 cm + Ring + Nut
5. DC Motor 12V Merk.NISCA Type.NC5475C
6. Timming Pulley 20 Teeth Bore 6.35 mm
7. Fully Thread Rod Size.M8 x 15 cm
8. Timming Pulley 40 Teeth Bore 8 mm
9. Timing Belt Type.2GT-200
10. Encoder + Sensor Canon Printer IP2770
11. High Current Motor Driver Type.BTS-7960
12. Connector DB15 Female
13. Bolt + Nut + Ring M3 x 1 cm
14. DC Power Connector Size.5.5 mm Female
15. Jumper Cable Arduino
16. Boss Kit Racing Steering Wheel
17. Skeleton Steering Wheel SKT-A SW8914
MORE VIDEO TUTORIALS
ARDUINO CONTROLLER BOX FOR DIY STEERING WHEEL
• ARDUINO CONTROLLER BOX...
DIY PEDALS GAME SIMULATOR
• DIY PEDALS FOR DRIVING...
ASSEMBLY 12V DC POWER SUPPLY FOR DIY STEERING WHEEL
• ASSEMBLY 12V DC POWER ...
DIY H SHIFTER FOR DRIVING SIMULATOR
• DIY H SHIFTER FOR DRIV...
SETTING STEERING WHEEL ARDUINO LEONARDO
• SETTING STEERING WHEEL...
TUTORIAL UPLOAD FIRMWARE TO ARDUINO LEONARDO
• TUTORIAL UPLOAD FIRMWA...
Source :
www.kaskus.co....
Credit :
- AI WAVE
- Arduino.cc
- Forum Kaskus

Опубликовано:

24 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 410

@muhammadrijalalmahdi5704 Год назад

Turotial terlengkap dan terjelas yg ada di youtube.. Mantapp🎉😅

@edipurwanto25 Год назад

Terima kasih, semoga tutorialnya bisa bermanfaat 🙏

@Ch10ne 3 месяца назад

excelente proyecto, pero tengo una duda ¿como conectas el motor a la fuente de la pc?

@edipurwanto25 3 месяца назад

utiliza un conector de alimentación de 3,5 mm

@hafeezunban6003 Год назад

THANK YOU BROOO!!! ITS NOW WORKKKKK

@edipurwanto25 Год назад

Good work Bro

@0utj 10 месяцев назад

Hello, I made it as in the pictures, the same firmware. Well, FFB doesn't work for me. Poking with a multimeter, I discovered that the PWM signal (which comes out from pin 10-11) produces a low level of 0.9V. and for this reason, the motor driver supplies only 3-4V to the motor and it hardly turns. I don’t know where to dig anymore, all the components are fully functional.

@3xAudio 3 года назад

cool project

@edipurwanto25 3 года назад

Thank you very much

@GT_FREAK 3 года назад

Great build bro!, How much torque does it have?

@edipurwanto25 3 года назад

Thanks bro, the torque is not big because it's for playing ETS2.

@GT_FREAK 3 года назад

@@edipurwanto25 Ahh ok thanks

@edipurwanto25 3 года назад

@@GT_FREAK You're welcome

@julianpussetto9739 Год назад

amazing, which encoder can I use if I don't have the Canon IP2770?

@edipurwanto25 Год назад

Can, but you have to know the ppr value, vcc+, ground, rx and tx encoder to be used

@MrAndrjuha 3 года назад

At some point i think 8mm rod can be changed to 10mm,but I realise too late already ordered 8mm pulley😄

@edipurwanto25 3 года назад

You can also change the timing pulley to 72 teeth for more torque.

@MrAndrjuha 3 года назад

Maybe later will do,but first have to finish this:-)

@jetpatrick6503 2 года назад

Nice work bro. Does the m8 fit tight on boss kit? How did you plant the m8 in if it is not fit?

@edipurwanto25 2 года назад

Thanks bro, in the middle hole of the bosskit I planted M8 nut

@Odadingmangoleh-b1k 2 года назад

mantap bang

@edipurwanto25 2 года назад

Terima kasih

@voxalonarlok4934 3 года назад

any chance i could get the arduino sketch for the encoder? im building a flight simulator and i think these would work nicely

@edipurwanto25 3 года назад

Sorry bro I don't have 🙏

@bossoy0769 3 месяца назад

how much ppr does the printer encoder have, that you use?

@Jackson_labely Год назад

@edi purwanto bang coba buat video untuk instalasi kabel nya pusing kalo liat dari foto

@edipurwanto25 Год назад

Lebih mudah belajar lewat gambar wiringnya mas

@sudiptmandal5607 Год назад

bro i am trying to do this but i am using epson 4800 printer encoder but not work just wheel is rotade continusly tell me why?

@edipurwanto25 Год назад

I don't know bro, it could be that the cable path is not correct or the encoder doesn't match 🙏

@simulatormania1831 3 года назад

Kerennn

@edipurwanto25 3 года назад

Terima kasih

@khdevofficialyt8856 9 месяцев назад

permisi bg mau tanya , knpa punya saya ga berfungsi ffb nya , sya pakai psu pc yg udh sya buang proteksinya . bts7960 udh saya coba ganti² ttp aja , kira² ada dimana ya Salahnya

@edipurwanto25 9 месяцев назад

Kalau semua komponen elektronik sudah dipastikan normal kemungkinan ada kesalahan/instalasi jalur kabelnya.

@mugendramon8377 Год назад

Bang itu di tengah as drat 8mm apa namanya yg item item nempel sama kaya ring gitu

@edipurwanto25 Год назад

Itu ring terbuat dari karet tebal untuk menempel rotary Encoder

@CrappyDude 2 года назад

You already answered the total cost of this project i mean the paddles shifters etcc.. which is 100$ But i want to know the total price of thiss gaming wheel Only the wheel which your building in this particular video.

@CrappyDude 2 года назад

Also (Robocraze BTS7960B Bridge Motor Driver) can i use thiss instead of BTS 7960..

@edipurwanto25 2 года назад

@@CrappyDude Estimated around $39.5 because I bought a used Canon printer encoder + sensor and dc motor

@edipurwanto25 2 года назад

@@CrappyDude I don't know if there is any difference between BTS7960 and BTS7960B

@CrappyDude 2 года назад

@@edipurwanto25 its same but can you once check it cuz then i have to order it and also thank you for replying me🔥🤗

@edipurwanto25 2 года назад

@@CrappyDude If I look at the specifications and functions are the same

@rickyrifaldy9992 4 месяца назад

bang nyari bahan2nya online apa di matrial sama bengkel2?

@edipurwanto25 4 месяца назад

Ada yang online dan ada yang beli ofline

@jokokelono5561 3 года назад

nice

@edipurwanto25 3 года назад

Thanks

@arnautandrei5786 2 года назад

How many degrees does the steering wheel rotate? Is it doable for someone who didn`t use Arduino before but programmed in C#? nice vid

@edipurwanto25 2 года назад

900 degress, the program is used for arduino

@arnautandrei5786 2 года назад

@@edipurwanto25 no, I mean is it hard to use for someone who programmed before but not in arduino

@edipurwanto25 2 года назад

@@arnautandrei5786 I got the program from the source which is written in the description and used for arduino. I don't know if it can be used for anything else.

@arnautandrei5786 2 года назад

@@edipurwanto25 no bro, I mean is it hard to learn programing in Arduino?

@edipurwanto25 2 года назад

@@arnautandrei5786 Not hard bro, I also just started making this steering wheel a year ago.

@lurkingcorsa10 9 месяцев назад

omm mimin, itu motor dc ny koq dcari gk ketemu. ad alternative laen kgk?

@edipurwanto25 9 месяцев назад

shp.ee/e866tkq

@edipurwanto25 9 месяцев назад

Bisa juga diganti motor DC lain

@lurkingcorsa10 9 месяцев назад

@@edipurwanto25 kalo pake rs 775..?

@mugendramon8377 Год назад

Dc motor merk nisca bisa diganti sama yg lain bang?

@edipurwanto25 Год назад

Bisa diganti merek apa aja, sesuaikan spesifikasi yang dibutuhkan

@MrAlejandroexe 9 месяцев назад

Could you provide us the WheelConfig_0.21 software?

@_Itachi_240_ Год назад

is it possible in arduino uno

@edipurwanto25 Год назад

Arduino Uno does not support force feedback

@_Itachi_240_ Год назад

@@edipurwanto25 oh ok Thanks for the reply

@edipurwanto25 Год назад

@@_Itachi_240_ You're welcome

@_Itachi_240_ Год назад

If I don't need Force feedback can I use Arduino uno

@edipurwanto25 Год назад

@@_Itachi_240_ Can Bro

@rileytedja2475 2 года назад

halo gan pnya sya calibration eror terus, saya sdh rubah tpi mai blm bisa.

@edipurwanto25 2 года назад

Kalau calibration error pilih advance setting -> reset to default

@atengtong3501 4 месяца назад

Bang cara nambah tombol untuk steering wheel ny gimana ya apa harus tambah lgi arduino ny?

@edipurwanto25 4 месяца назад

Mau tambah berapa tombol ?

@atengtong3501 4 месяца назад

Kira² 10 tombol

@edipurwanto25 4 месяца назад

@@atengtong3501 kalau nambah sepuluh tombol bisa pakai module joystick PS atau keyboard

@atengtong3501 4 месяца назад

Berarti dual kontroler gpp ya bang 1 pakai arduino satunya pakai joystik gitu bisa ya

@p1gxz535 2 года назад

caa masukin drat ke piloblock gmn?

@edipurwanto25 2 года назад

Tinggal dimasukin aja ke lobang bearingnya tapi baut pengunci as di bearing di kendurkan dulu.

@Anadisty Год назад

Sensor encoder pake punya arduino sensor kaki 5 inputnya 360 apa gimana bang?

@edipurwanto25 Год назад

Sensor dan encodernya pakai punya printer Canon iP2770

@Anadisty Год назад

@@edipurwanto25 ok bang udah ketemu PPR dari sensor ada yg nyebut 20 lumayan hemat biaya masih riset per part nya gimana

@pianomusic4754 2 года назад

Like si no entiendes Ingles

@edipurwanto25 Год назад

Yes my english is bad

@kentin6348 Год назад

hello bro, where can i find the arduino program to make all of this work? Thannnnks :)

@edipurwanto25 Год назад

You can download it here drive.google.com/file/d/1te7JQN99EqIt1OpGkDNpAO1ezo7XkxAt/view?usp=drive_link

@nge-gamebae7940 7 месяцев назад

Halo pak, setting encordeenya gimana ya??

@edipurwanto25 7 месяцев назад

Cara settingnya ada di channel yang judulnya setting steering wheel arduino

@hafeezunban6003 Год назад

Hi bro my steering wheel is broken at first i thought it was encoder sensor then i replace it nothing happend then i thought it was encoder so i replace it same nothing happend but i remember that my first time try it work but after i install xloader and the forum it broke😢

@edipurwanto25 Год назад

Why is it broken bro? I've been using my steering wheel for over two years and it's fine

@hafeezunban6003 Год назад

@@edipurwanto25 idk after i install xloader and upload the forum its not detect

@edipurwanto25 Год назад

@@hafeezunban6003 Maybe there was an error that you made during the upload process with xloader or indeed your arduino is having a problem. The solution is you have to replace it with a new one

@hafeezunban6003 Год назад

@@edipurwanto25 ok thanks😥

@mugendramon8377 Год назад

Kalo ada blue print diameter lubang sama jarak antar lubang di pvc sheetnya boleh dong bang di share

@edipurwanto25 Год назад

Kebetulan pas buatnya langsung ukur dan coret di papan PVC jadi tidak ada drawingnya. Saran saya kalau mau buat untuk timing pulley yang ukuran 40 teeth ganti ke ukuran 80 teeth supaya ffb nya lebih besar

@Mert-ot8db Год назад

How did you fix it to the table at the end?

@edipurwanto25 Год назад

For installation on the table using brackets and clamps

@modssrcreation2222 5 месяцев назад

Z toggle buat apa ya bang

@edipurwanto25 5 месяцев назад

jika firmware terbaca 0.00 di wheel config matikan Z-toggle dan putar stir ke kiri dan kanan sampai terbaca 0.16 lalu hidupkan lagi

@MrAndrjuha 3 года назад

Hello,what lenght of Timing Belt Type.2GT-200 you have there? Is it 100 mm?

@edipurwanto25 3 года назад

Length 200 mm, width 6 mm

@MrAndrjuha 3 года назад

@@edipurwanto25 OK thanks,I following your video and started buy all parts I needed.By the way is 775 dc motor will be OK for this project?As I don't have anything else,I would like to reuse it

@edipurwanto25 3 года назад

@Andrejs Gerasimovs You can use 775 DC motor but the bore timing pulley adjusted to the diameter of the 775 DC motor shaft

@p1gxz535 2 года назад

Untuk bts 7960 pakai apa, untuk si sekrup di pvc

@edipurwanto25 2 года назад

Saya pakai plat tipis bekas bracket motor printer

@RecehDIY 2 года назад

om, motor nya kuat kah? bisa bikin pegel tangan gak? lebih kuat mana torque nya ketimbang 775 om?

@edipurwanto25 2 года назад

Motornya kuat, kalau mau torque besar bisa pakai 2 motor dan pulley nya juga di ganti yg lebih besar. Saya belum coba pakai 775

@Potatoleague-ux2zc Год назад

Hi can I use DC motor with encoder instead of canon sensor I don't need to have force feedback too

@edipurwanto25 Год назад

You can use another brand of encoder, but you must know the PPR value. If you don't need force feedback don't use DC motor

@Potatoleague-ux2zc Год назад

@@edipurwanto25 so if I have DC motor with encoder and I know the ppr what is next I can follow the video and btw your videos are great

@Potatoleague-ux2zc Год назад

@@edipurwanto25 and I found online the same encoder you have but I don't have the disk you used

@edipurwanto25 Год назад

@@Potatoleague-ux2zc Of course, you must know the PPR value because when making settings in the wheel config, you must enter the PPR value

@Potatoleague-ux2zc Год назад

@@edipurwanto25 thx

@Escarabajo69 2 года назад

Se te derretirá?? Ajjajaj veremos este verano…

@edipurwanto25 2 года назад

No entiendo lo que quieres decir

@tbilal11201 2 года назад

ini bosskit nya punya mana bang? ada link pembelian?

@edipurwanto25 2 года назад

Bosskit untuk Suzuki carry

@aldythsatya601 3 года назад

Ganti pulleynya ke htd yang 3m 72t lebih mantep torsi ffbnya

@edipurwanto25 3 года назад

Terima kasih sarannya bang, nanti di coba untuk stir yang satunya.

@aldythsatya601 3 года назад

@@edipurwanto25 saya dah coba dengan htd3m 72t untuk as stirnya dan 20t untuk motornya, set ffb 80%, spring 40% dampernya 30% dah kayak bawa truk tanpa power steering. Berat banget ffbnya hihi. Oh iya saya pakai motor dc my1016 psu 24v 20a, kalo abang pake apa?

@edipurwanto25 3 года назад

@@aldythsatya601 wah kalau kaya stir tanpa power steering tangan pegel kalau mainnya lama. Hahaha Saya pake motor Nisca NC5475C dan power supply 12V 10 Ampere.

@MrAndrjuha 3 года назад

Hi again,I got issue with encoder i have 4 of them but I don't now pinouts of them,can't find online eather. I have 2 Epsons and two hp printers encoders.

@edipurwanto25 3 года назад

To make it easy you have to get an encoder + sensor Canon Printer IP2770. Is it not available in your country?

@MrAndrjuha 3 года назад

@@edipurwanto25 Unfortunately nope.

@MrAndrjuha 3 года назад

Just need to find pinouts for them and wola job done:-D

@funny-mannyvor8jahren583 Год назад

Sorry, but can you tell me what exactly z toogle (26:00) is and what it is used for? And is it possible, to use more than two extra buttons? (Maybe you can switch it with the z toogle lever)

@edipurwanto25 Год назад

Z toggle function if the firmware is not read in the wheel config (0.00) then you have to remove the Z toggle, turn the steering wheel left and right. The firmware will change to 0.16. You can add buttons using arduino pins D12, D13, A3, A4 and A5

@funny-mannyvor8jahren583 Год назад

@@edipurwanto25 Thank you for the answer 😁

@funny-mannyvor8jahren583 Год назад

@@edipurwanto25 But I have to change the code in I want to add buttons, right?

@edipurwanto25 Год назад

@@funny-mannyvor8jahren583 You're welcome, yes you have to set it in the wheel config to add buttons

@funny-mannyvor8jahren583 Год назад

Wait, is the firmware supporting that?

@tristan6509 2 года назад

Itu bosskit untuk mobil apa bos? Soalnya tiap mobil beda2, takutnya mur nya terlalu longgar kalo salah tipe

@edipurwanto25 2 года назад

Buat mobil carry bos

@tristan6509 2 года назад

@@edipurwanto25 ok makasih bosqu

@mugendramon8377 Год назад

Total budget abis brp bang buat steering wheelnya?

@edipurwanto25 Год назад

Komplit dengan pedal, shifter, box control arduino dan power supply kurang lebih 1,5 juta

@MrMarto 3 года назад

does it have delay?

@edipurwanto25 3 года назад

I use playing ETS2 doesn't delay

@ninjagola8471 2 года назад

Bang habis berapa ya kira kira total bikin setir,pedal sama shifternya. Soalnya mu nyiapin dananya

@edipurwanto25 2 года назад

Kurang lebih 1,4 juta bang

@kennethmanthis2457 3 года назад

i have a Rotary Encoder instead a Encoder + Sensor of printer how to put it in.

@edipurwanto25 3 года назад

Sorry bro I haven't tried using the rotary encoder, maybe the working principle is the same 🙏

@kennethmanthis2457 3 года назад

@@edipurwanto25 here's what i am thinking. put a gear on Rotary Encoder and at the end of the thread that is connected to the steering wheel. or adding one more Timming Pulley and belt connected to rotary encoder and the steering wheel. that;s gonna work right?

@edipurwanto25 3 года назад

@@kennethmanthis2457 I think the gears or timing pulley are the same and you can try, but the rotary encoder settings may be different in the wheel config. Try looking for tutorials using a rotary encoder.

@jorgesernaque2349 2 года назад

how much did you spend to buy everything?

@edipurwanto25 2 года назад

To make the steering wheel, pedals, shifter and arduino controler box estimate of approximately $100

@josiah.cameruh 2 года назад

Can I use a 1000 rpm motor or less, if soo Dow low rpm can I go

@edipurwanto25 2 года назад

Yes, can

@josiah.cameruh 2 года назад

@@edipurwanto25 what rpm can I do

@edipurwanto25 2 года назад

@@josiah.cameruh You don't need to use large rpm but use large torque for force feedback.

@edipurwanto25 2 года назад

@@josiah.cameruh The DC motor I use force feedback is sufficient for playing ETS2 but for playing Dirt4 force feedback is lacking. Maybe later I will make it with another DC motor.

@adimulyadi4469 2 года назад

Udh coba di test buat ngedrift ga bang,?

@edipurwanto25 2 года назад

Belum bikin handbrake nya, tapi saya yakin bisa di pake ngedriff 🤭

@hafeezunban6003 Год назад

Hi bro can you give me the most latest firmware thanks

@edipurwanto25 Год назад

I only have this drive.google.com/file/d/1te7JQN99EqIt1OpGkDNpAO1ezo7XkxAt/view

@hafeezunban6003 Год назад

@@edipurwanto25 ok thanks

@edipurwanto25 Год назад

@@hafeezunban6003 You're welcome

@ongguen Год назад

Bang, ko pake 2 motor rs 775/795 apakah psu nya jga ditinggikan bang? Misal dari 12v yg awalnya cuma 1 dc, klo pake 2 motor apa psu harus up ke 24v ya bang?

@edipurwanto25 Год назад

Tidak perlu kalau pakai motornya 2 x 12V tetap power supply nya pakai yang 12V

@ongguen Год назад

Klo untuk ampernya apa ttep 10A atau 20A duakali lipatnya bang?

@edipurwanto25 Год назад

@@ongguen untuk 2 x motor DC 775 menurut saya sudah cukup pakai power supply 10A

@ongguen Год назад

Brarti 10-15A gpp ya bang? Makasih ilmunya bang, sangat bermanfaat, sukses slalu

@hafeezunban6003 Год назад

hi bro can it use on forza horizon 4?

@ernestoutright6265 2 года назад

Mas ada link pembelian. Baut panjang, pulley dll gak

@edipurwanto25 2 года назад

Saya beli online di shopee mas, nanti saya copy linknya

@Memescience 2 года назад

Ijin kak untuk power suply ny pakek punya ap kak

@edipurwanto25 2 года назад

Ngerakit sendiri, cek video yang judulnya assembly 12V DC Power Supply. Bahan2 beli di toko online.

@musichero945 2 года назад

can use arduino uno ?

@edipurwanto25 2 года назад

Can, but arduino uno does not support force feedback

@hafeezunban6003 Год назад

Hi bro i have buy 2 arduino at first it was detect as keyboard then i refund second i buy it was same thing happened and it was tested the seller say the refund arduino was not broken please help me

@edipurwanto25 Год назад

Why is it like that bro, it should be detected as arduino. I have tried on 2 PCs and 1 laptop, all are detected as arduino.

@hafeezunban6003 Год назад

@@edipurwanto25 bro i have upload the firmware using xloader and it detect as other device but then when i test on wheel confiq its not moving the steering

@hafeezunban6003 Год назад

@@edipurwanto25 i have complete the steering wheel 99% just 1% is the problem😭 please help me bro

@edipurwanto25 Год назад

@@hafeezunban6003 Have you installed arduino drivers? You have to make the device detect as arduino for the steering wheel to work.

@hafeezunban6003 Год назад

@@edipurwanto25 yes done

@viniciusschmidt9050 3 года назад

can i use the 775dc motor?

@edipurwanto25 3 года назад

You can use 775 DC motor

@fajaroutbox847 Год назад

Mas, saya kemaren rakit stering whell pakai puly mesin jahit, dinamo RS 795 PSU pakai bekas PC 12v, -+14A, diconfig stir sudah sukses, dimainkan di ETS2 berat banget lalu pas belok itu lawan arus putaran dinamo ko bisa short ke PSU nya, kira2 knapa ya? & juga kabel PSU ke motor driver nya panas

@edipurwanto25 Год назад

Saran saya setingan spring, dumper dan lain2 jangan terlalu besar karena motor akan kerja keras dan panas sehingga bisa mengakibatkan short. Saya sudah 2 tahun pakai steering DIY belum pernah mengalami short cuma motor saja yang terasa panas makanya di video DIY yang lain saya tambah cooling fan biar motor tidak terlalu panas.

@fajaroutbox847 Год назад

Ok trimakasih mas jawabannya 👍

@fajaroutbox847 Год назад

Oh ya mas klo pakai PSU bekas PS3 12v 32A kuat ga?

@edipurwanto25 Год назад

@@fajaroutbox847 Sesuaikan dengan motornya mas, saya pakai motor nisca NC5475B dan pakai power supply 12V 10 Ampere sampai sekarang aman tidak ada masalah.

@fajaroutbox847 Год назад

Terlalu besar ga puley nya?

@hafeezunban6003 Год назад

Can it use on ps5

@edipurwanto25 Год назад

Sorry I don't know and I don't have PS5 🙏

@hafeezunban6003 Год назад

@@edipurwanto25 ooh ok btw im 80% complete

@edipurwanto25 Год назад

@@hafeezunban6003 Good job bro 👍

@nico_poriol 2 года назад

Will this work on forza horizon 4 and 5?

@edipurwanto25 2 года назад

I haven't tried it yet but I'm sure it works

@egofficial581 Год назад

Bro kalo mau pesen bsa ga, biaya brpa?

@edipurwanto25 Год назад

Maaf bro saya tidak menjual 🙏

@MrAndrjuha 3 года назад

Is it ok to use Freenove because that what i have or it only work with Arduino?

@edipurwanto25 3 года назад

I don't know bro, it's better if you buy arduino leonardo R3 clone the price is around $6

@MrAndrjuha 3 года назад

@@edipurwanto25 Thanks bro!

@edipurwanto25 3 года назад

@@MrAndrjuha Okay

@MrAndrjuha 3 года назад

@@edipurwanto25 There is no chance download firmware,wheel config file,and .hex file can you help me get them please?

@edipurwanto25 3 года назад

@@MrAndrjuha m.kaskus.co.id/show_post/5879c1b9ded770e7728b456c/1326/tutorial-steering-wheel-with-arduino-leonardo

@muhammadsafarif125 2 года назад

Mas ada skema pemasangan db15nya?saya gk paham soalnya, pake db15 kelihatan simple buat dipake

@edipurwanto25 2 года назад

DB15 ada 15 pin jadi bebas pakai pin mana saja asalkan pin yang dipakai antara DB15 male dan DB15 female sama.

@muhammadsafarif125 2 года назад

@@edipurwanto25 jadi untuk kabel penghubung antara db15 itu juga harus sama ya?

@edipurwanto25 2 года назад

@@muhammadsafarif125 iya mas harus sama.

@kisarasiriwardhana4243 2 года назад

Can I use any printer encorder+sensor How to buy the encorder sensor you used

@edipurwanto25 2 года назад

You can find it in the online shop

@kisarasiriwardhana4243 2 года назад

Can you give me a link

@kisarasiriwardhana4243 2 года назад

Can I use any sensor encorder

@edipurwanto25 2 года назад

@@kisarasiriwardhana4243 You can search for recommendations on google

@edipurwanto25 2 года назад

@@kisarasiriwardhana4243 can, if you know the pin out.

@anggitarwianata3827 2 года назад

step upload program nya ke arduino Leonardo, kemana bang ? kok di skip

@edipurwanto25 2 года назад

Cek di deskripsi / beranda yang judulnya tutorial upload firmware ke arduino leonardo

@onurcanylmaz1917 2 года назад

I am also using printer encoder but i dont know ppr and stuff can u enlighten me? I need Command mode, PWM frequency, Encoder ppr

@edipurwanto25 2 года назад

Settings using the encoder canon ip 2770 PWM 20 kHz and PPR 2150

@agungwibowo24 3 года назад

Encordernya pake EPSON bisa ga bang...

@edipurwanto25 3 года назад

Saya belum coba pakai encoder lain 🙏 Beli saja yg punya Canon iP2770 di online ada. Saya beli second 2 set murah dan keduanya bisa digunakan.

@bangkurosok7641 2 года назад

Download ai wavenya dimana ya om linknya pada mati semua 🙏🙏🙏

@edipurwanto25 2 года назад

Lihat di kolom komentar ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-KFkdccBlhwk.html

@bangkurosok7641 2 года назад

@@edipurwanto25 makasih om Edi 🙏🙏🙏

@edipurwanto25 2 года назад

@@bangkurosok7641 sama - sama

@holdenlasepy8029 Год назад

Bro ada tutorial kalau mau nambah bbrp tombol pakai rangkaian ini?

@edipurwanto25 Год назад

Mau menambah berapa banyak tombol bro ?

@holdenlasepy8029 Год назад

@@edipurwanto25 misal lebih dr 2 tombol, hrus nambah controller kah?

@edipurwanto25 Год назад

@@holdenlasepy8029 saya menggunakan pin di arduino D12, D13, A3, A4 dan A5 untuk tombol dan pin lainnya untuk stir, shifter dan pedal.

@saddammurtadho6167 2 года назад

selain motor merk nisca apalagi om rekomendasi ?

@edipurwanto25 2 года назад

Untuk motor bebas mau pakai merk apa saja yg penting 12V DC contoh seperti motor DC 775 dll. Motor 24V DC juga bisa tetapi power supply juga gunakan yang 24V DC

@saddammurtadho6167 2 года назад

@@edipurwanto25 ig apa om kalo mau nanya"

@edipurwanto25 2 года назад

@@saddammurtadho6167 ada di deskripsi channel

@zilcard959 Год назад

Power supplynya pakai apa om?

@edipurwanto25 Год назад

Power supply 12V 10A, beli di shopee

@zilcard959 Год назад

@@edipurwanto25 ok om, ceritanya aku mau ambil motor rs775 dua buah, apa power supplynya masih cukup

@edipurwanto25 Год назад

@@zilcard959 cukup mas

@zilcard959 Год назад

@@edipurwanto25 kalau masalah kabel, kabel awg berapa om? Lalu kalau mau pakai motor my6812 kan 100 watt tuh, nah harus pakai psu apa?

@mysongs6386 2 года назад

Klo tombol" lain seperti lampu, klakson, sein dll itu bisa ngambil ke arduino gk bang? Makasih🙏

@edipurwanto25 2 года назад

Bisa bang

@Muhammad_rifqi_fauzi 2 года назад

@@edipurwanto25 bang di jual gak bang

@edipurwanto25 2 года назад

@@Muhammad_rifqi_fauzi Tidak untuk di jual hanya digunakan sendiri.

@Muhammad_rifqi_fauzi 2 года назад

@@edipurwanto25 pandu cara buat nya bang minta nomer wa atau social media lain nya

@edipurwanto25 2 года назад

@@Muhammad_rifqi_fauzi sosmed ada di channel dan cara membuatnya sudah ada videonya

@agung8374 3 года назад

Mas punya saya ffb nya nggk berfungsi, terus di wheel config wheel error

@edipurwanto25 3 года назад

Pemasangan kabelnya sudah sesuai belum mas coba di cek soalnya butuh ketelitian dalam pemasangan.

@edipurwanto25 3 года назад

Kalau pemasangan sudah sesuai pasti bisa berfungsi, lihat link di deskripsi ( forum Kaskus ) ikuti petunjuknya.

@agung8374 3 года назад

Mas punya no wa atau FB, biar saya tanya2 bisa lebih jelas lagi

@edipurwanto25 3 года назад

@@agung8374 chat di FB atau IG mas

@agung8374 3 года назад

@@edipurwanto25 ini udah saya susun ulang kabel nya tapi malah stirnya muter terus

@zokey2222 2 года назад

Csá tesó más játékokhoz is használható vagy csak ets2? Can it be used for other games or just ets2?

@edipurwanto25 2 года назад

Most próbáltam ki ETS 2-n és Dirt 4-en a források szerint más játékokhoz is használható

@Automaniac2021 2 года назад

Bro Any alternative encoder bcoz it's not available here

@edipurwanto25 2 года назад

Can use other encoder but you have to know pin out and ppr value.

@Automaniac2021 2 года назад

@@edipurwanto25 ok thank you

@edipurwanto25 2 года назад

@@Automaniac2021 You're welcome

@Automaniac2021 2 года назад

@@edipurwanto25 is there any options to change code

@edipurwanto25 2 года назад

@@Automaniac2021 What code do you want to change?

@psatirhandal6927 2 года назад

Masang kabel dari dinamo sama Colokan DC, ke motor drivernya kebalik gpp kan bang? Takut konslet 😂

@edipurwanto25 2 года назад

Kalau yang konektor DC ke motor driver jangan kebalik mas takutnya motor drivernya rusak 😀

@josiah.cameruh 2 года назад

What rpm is the motor

@edipurwanto25 2 года назад

2700 rpm

@ferijo5091 Год назад

Link wheelconfig nya tidak bisa om?

@edipurwanto25 Год назад

drive.google.com/file/d/1t6pmFPTaj8-_hdmIv8C6xW7wvoXgMMKL/view

@ferijo5091 Год назад

@@edipurwanto25 yg wheel config om, bukan wheelcheck 😁

@edipurwanto25 Год назад

@@ferijo5091 drive.google.com/file/d/1qqn_AB4W4dVudkD8PfeNCIyneriHxDsL/view

@ayrtonmarin6778 2 года назад

I want to build one with a Nema 34 8nm or 12nm stepper motor, what do you say?

@edipurwanto25 2 года назад

I have stepper motor but haven't tried it yet.

@shilviayufitrya7259 7 месяцев назад

Dijual gk?

@edipurwanto25 7 месяцев назад

Tidak di jual 🙏

@shauf_gaming Год назад

bahannya saja habis brp om?

@edipurwanto25 Год назад

Kalau yang model begini komplit sama pedal & shifter biaya bahannya kurang lebih satu jutaan.

@groovy8829 2 года назад

Can we use Table Fan motor ac

@edipurwanto25 2 года назад

Can't, because the motor driver used is DC

@groovy8829 2 года назад

@@edipurwanto25 okay thank you

@groovy8829 2 года назад

And one thing,can we use another printer encoder

@edipurwanto25 2 года назад

@@groovy8829 You're welcome

@edipurwanto25 2 года назад

@@groovy8829 It's possible if you know the pinout and ppr value

@p1gxz535 2 года назад

bosskit nya suzuki apa gan?

@edipurwanto25 2 года назад

Suzuki carry gan

@p1gxz535 2 года назад

@@edipurwanto25 pnya sya jga gtu gan, tpi kok bolongan lebih besar dri 8mm

@edipurwanto25 2 года назад

@@p1gxz535 lihat di video saya mas di lobang bosskitnya saya tanam mur M8

@p1gxz535 2 года назад

@@edipurwanto25 mksih

@edipurwanto25 2 года назад

@@p1gxz535 sama-sama

@dimaselonmusk4908 Год назад

Bang buat pedalnya Bang tutorial buat pedal gue bayar Rp200.000 di shopee Bang Bang gue bayar shopee bikin pedangnya aja Bang kalau nggak bikin pedangnya bikin sekarang pegang sama Arduino nya Bang

@edipurwanto25 Год назад

Tutorial bikin pedalnya sudah ada di channel saya, mohon maaf saya tidak jualan 🙏

@p1gxz535 2 года назад

bang potong pvc pakai apa

@edipurwanto25 2 года назад

Potong manual pakai gergaji besi

@p1gxz535 2 года назад

@@edipurwanto25 ada link pembelian mas?

@edipurwanto25 2 года назад

@@p1gxz535 shopee.co.id/product/42165804/6279352184?smtt=0.154633846-1651488911.9

@toastedbagel9095 3 года назад

Is it any better than G25 or G27? Also, how much did it cost in total (USD)?

@edipurwanto25 3 года назад

I haven't tried the G25 or G27 yet and I made steering wheel to be able to play the simulator at low cost ( the estimated cost is around $100 )

@toastedbagel9095 3 года назад

@@edipurwanto25 Does that come with the pedals or $100 for the wheel only? Is it noisy? Sorry for many questions

@edipurwanto25 3 года назад

@@toastedbagel9095 for all ( steering wheel, pedals and shifter ) not noisy

@toastedbagel9095 3 года назад

@@edipurwanto25 okay thanks for answering my question!

@edipurwanto25 3 года назад

@@toastedbagel9095 You're welcome

@anggasetiawan7988 2 года назад

itu pake stir yg brpa inci om

@edipurwanto25 2 года назад

Diameter 320mm ( sekitar 12,5 inch )

@05iketutsagotrawangsa59 3 года назад

Dinamo belinya di mana bang?

@edipurwanto25 3 года назад

Di toko online shopee

@p1gxz535 2 года назад

Cable db15 gimana gan?

@edipurwanto25 2 года назад

Maksudnya gimana apanya ?

@p1gxz535 2 года назад

@@edipurwanto25 pemasangan cable db15 gimana

@edipurwanto25 2 года назад

@@p1gxz535 DB15 ada 15 pin jadi bebas pakai pin mana saja asalkan pin yang digunakan antara male dan female harus sama

@p1gxz535 2 года назад

jadi kalau solder 8/15 pin msi bsa?

@edipurwanto25 2 года назад

@@p1gxz535 pakai 8 kabel bisa kan maximal 15 kabel

@dennywahyu9233 2 года назад

Bang , disini arduino , di controller box juga arduino , berarti btuh 2 bang arduinonya

@edipurwanto25 2 года назад

Cuma satu arduino yg di controller box, kalau yg di stir cuma motor driver.

@dennywahyu9233 2 года назад

Yg di belakang motor driver , ada tanda merah & biru itu apanya bang ???

@edipurwanto25 2 года назад

@@dennywahyu9233 Itu terminal kabel untuk paralel tegangan 5V dan ground.

@dennywahyu9233 2 года назад

Memang namanya terminal kabel gitu ya bang ??

@edipurwanto25 2 года назад

@@dennywahyu9233 Terminal Paralel Warna 2 Input 6 Output SPL62 Itu namanya cari di shopee

@suharyono1236 3 года назад

Pake dinamo beda bisa

@edipurwanto25 3 года назад

Bisa mas

@suharyono1236 3 года назад

@@edipurwanto25 dinamo printer bisa

@edipurwanto25 3 года назад

@@suharyono1236 stir saya yang satu lagi juga pakai 2 dinamo bekas printer.

@wahidkurniawan1174 3 года назад

Review pedalnya om

@edipurwanto25 3 года назад

Kalau ada waktu nanti dibuatkan juga videonya, masih sibuk kerja dan bisa buat video ketika libur 🙏

@wahidkurniawan1174 3 года назад

@@edipurwanto25 sip om ditunggu 👌

@rayhanfadilah171 2 года назад

Om itu dinamonya kuat ga,pakai stir asli,,bukan stir racing

@edipurwanto25 2 года назад

Kuat mas

@rayhanfadilah171 2 года назад

Siap makasih infonya om,tapi kalau mau tambah jadi 2 motornya bisa ya

@edipurwanto25 2 года назад

@@rayhanfadilah171 bisa malah lebih bagus pakai dua motor

@rayhanfadilah171 2 года назад

@@edipurwanto25 ada ig,atau apa gitu om biar nanti ngobrolnya enak

@edipurwanto25 2 года назад

@@rayhanfadilah171 ada di channel saya

@gindiyanti4976 3 года назад

Total berapa

@edipurwanto25 3 года назад

Total biaya untuk semuanya ( stir, pedal & shifter ) kurang lebih 1 - 1,5jt

@Thegreatdrive41 2 года назад

bang kira2 habis berapa ya

@edipurwanto25 2 года назад

Untuk semua ( stir, pedal, shifter ) biaya nya kurang lebih 1 - 1,5 JT bang. Kalau menggunakan kayu dan part2 bekas bisa lebih murah ( di bawah 1 juta )