DIY Toddler bed / Montessori bed Easy to build // transitional period before a larger bed 

Well I would love to see the picture you can Instagram me at Kushnirmike

0:53 dhdbdjjdndkdhdkdhdjdhhdk😢d dhdkddj😅dhe

Thanks I appreciate it🙏

Thanks 🙏

In the Center from bottom to top Peak is 66 1/2 inches and the side from bottom to top this 50 inches

Material list 6 Pieces of 3x3x8 or 2x4x8 3 Pieces of 2x6x8 Box of screws 3 inches I’m using 3/8 drillbit to pre-drill the holes for the screw Side posts Cut 4 pieces out of 3x3 to 4ft long one of the ends in 22 1/4 degrees Rooftop Cut 4 pieces out of 3x3 to 43” long one of the ends in 22 1/4 degrees Cut 2 pieces of 2x6 74 inches long Cut 3 pieces of 3x3 38 inches long Cut 2 pieces of 2x6 38 inch long

You’re the best ! Thank you so much 🙏🏼✨

You’re welcome

@@mikekushnir6978 thank you so much, I am a total newbie and I ll try it for my son. Thank you so much, which brand of drill do you recommend me to get to do work with wood ? Thank you

Your video says the roof trusses are 43” long but here you say they’re the same size as the side posts (4 feet or 48”) I’m following your instructions but the 74” sides were too short and I couldn’t figure out why until now. Also, the 2 1/2 inch screws were too long for the roof trusses, they went through and were showing about 1/2 an inch through the other side.

I got it. Starting at 2:56, any measurement that would be 38” will be 76”.

Yes you’re correct The highest edge is still 4 feet

Thank you for this answer lol, just about to cut my 3x3’s and was like wait a minute… 🤔🤔

Thank you for watching 🙏 Yes I primer first and then paint it with some white paint I had and I believe it was eggshell finish The measurements for a full-size is So instead of cutting 38 inches wide for a twin size you will be cutting 53 inches wide for a full size and the rest is the same

@@mikekushnir6978 perfect thank you so very much! Im hoping to get started this week.

Deidra Wills You are welcome

kreg jig pocket hole

sorry I do not have any plans But I wish I did ,maybe I need to look into it

Thanks 🙏

Around $50

www.homedepot.com/p/8-ft-Landscape-Timber-288731/301802514 www.homedepot.com/p/2-in-x-6-in-x-8-ft-2-BTR-KD-HT-SPF-Dimensional-Lumber-058443/312528832

www.homedepot.com/p/Kreg-2-1-2-in-Coarse-Zinc-Plated-Steel-Square-Head-Pocket-Screw-50-Pack-SML-C250-50/205377485

www.homedepot.com/p/Kreg-Pocket-Hole-Jig-KPHJ320/310410050

Drill, a strong one Bits, maybe like 3/8 or 1/2 bit to drill the holes The tool that was already suggested by the first reply Wood Table saw and if possible a chop saw Measure 3 times then cut Good luck

appreciate it thank you, yes you are correct Kreg jig is for 1.5 thickness And my 3 x 3 is more like 2 3/4 and no problem with It , it work out really good

www.homedepot.com/p/Kreg-Pocket-Hole-Jig-KPHJ320/310410050

This pocket hole jig it’s really handy, it makes building is easy

Are used 40 screws and they were 2 1/2 inch long any type Screws will be fine, and I used 120 grit sandpaper , good luck and thanks for watching

@@mikekushnir6978 Thank you for your response!

Yes and that a great idea

No I don’t have a material list for a full size But I think it would be mostly the same just the width would be wider depending on how wide is your full-size match

Kreg Pocket Hole #8 x 2-1/2-in

@@mikekushnir6978 nice. I was playing a guessing game based on the video. Hit it right on the money😎😎😂 thanks a bunch

Do not buy a table saw like the one he used. That thing is outdated and incredibly dangerous. The way he used it is also very dangerous if you’re not incredibly careful. If you buy a table saw make sure you fully understand all the ways you can be injured using one.

It was fairly cheap if I can remember it less than $45 for the materials thanks for watching 🙏

This is a twin size mattress measurements . If that’s your question?

Do you actually have written form of supplies that is needed. It is little unclear on the video. Would greatly appreciate if you could send all the supplies needed with measurements.

Ok gotcha i’ll get you the sizes soon

@@mikekushnir6978 still did not get the sizes. Do you mind sending it please. Also, what was the size of the whole that you made from kreg jig?

Material list 6 Pieces of 3x3x8 or 2x4x8 3 Pieces of 2x6x8 Box of screws 3 inches I’m using 3/8 drillbit to pre-drill the holes for the screw Cut 8 pieces out of 3x3 to 4ft long one of the ends in 22 1/4 degrees Cut 2 pieces of 2x6 74 inches long Cut 3 pieces of 3x3 38 inches long Cut 2 pieces of 2x6 38 inch long

You’re welcome thanks it’s called Kreg Pocket-Hole Jig

@@mikekushnir6978 thank you so much!

Pocket hole is the best investment I ever did for my projects lol

@@CIAragDe yes same here

I would recommend screws because nails will pull out

@@mikekushnir6978 okay so I can just use a basic drill?

Yep you get it

www.homedepot.com/p/Kreg-Pocket-Hole-Jig-KPHJ320/310410050

Material list 6 Pieces of 3x3x8 or 2x4x8 3 Pieces of 2x6x8 Box of screws 3 inches I’m using 3/8 drillbit to pre-drill the holes for the screw Cut 4 pieces out of 3x3 to 48”long one of the ends in 22 1/4 degrees (( walls)) Cut 4 pieces out of 3x3 to 43” long both ends in 22 1/4 degrees in parallel to each other ((roof)) Cut 2 pieces of 2x6 74 inches long ((bottoms sides)) Cut 3 pieces of 3x3 38 inches long ((too)) Cut 2 pieces of 2x6 38 inch long (( bottom)) Thanks for watching

Oh yeah that will work great , I just personally like the thickness of 3 x 3 look and 2 x 2 was a little too narrow of a look for me

Oh ok thanks

To follow up on this. Other than you not liking the look of a 2x2 look could it still work? Was considering cutting my 2x4 into a 2x2. Thoughts?

Sorry I don’t have plans

It cost me under $50 I can’t remember exactly

Yes it will 38 inches wide by 75 inches

@@mikekushnir6978 If i were to make this a toddler bed, would the lengths of the 2X6 boards be all that changes? 28X53?

I use 3 inch screws from Kreg jig screws