Тёмный

drilling cases stihl ms660 and husky 372xp 

Gangster Builder
Подписаться 2,9 тыс.
Просмотров 3,3 тыс.
50% 1

Опубликовано:

 

30 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 16   
@jamiebouchard9862
@jamiebouchard9862 3 года назад
It would almost seem like a good idea to do 1 hole, tap it and then u can secure the cylinder and do the remaining 3
@eddiewilson3419
@eddiewilson3419 4 года назад
Thank goodness the cylinder doesn’t have studs like the original head. I put a two piece cylinder on a case made with the single piece cylinder without a drill press. What a bitch to get the studs straight enough for the cylinder to fit just right ugh 3 hours it took when I thought it was gonna be 20 minutes. You do good work man this shit isn’t as easy as people think. Much respect for you and the very helpful videos you make! Thanks man
@jrsimpson8194
@jrsimpson8194 3 года назад
How much faster does that make it go
@TheLouisamite
@TheLouisamite 2 года назад
How do you get anything done with that mess on your work table
@vampire7878
@vampire7878 2 года назад
how did you line up the cylinder to be perfect so it don't cease? I seen another video of a guy do this and at part 3.5 when he had engine running it ceased 1.9 seconds in 0-0
@gangsterbuilder
@gangsterbuilder 2 года назад
I ran one 3 years. Engines that lock up are usually the circlips in the piston.
@gangsterbuilder
@gangsterbuilder 2 года назад
If you lower your piston to bottom dead center the piston will hold it in place
@YorHighness
@YorHighness 5 лет назад
Yes this helps tremendous..Nice Approach.
@maxscianimanico7279
@maxscianimanico7279 3 года назад
What size rod is that for the ms 660
@gerestevenson4484
@gerestevenson4484 3 года назад
What size studs do i need
@donaldellis9004
@donaldellis9004 4 года назад
You have got to use some editing software, I don't know nothing about the you tube thing and I'm trying to give you some kind constructive criticism, bro if you get your act together you will have thousands and thousands of subscribers man you could be making so much money BUT YOU HAVE GOT TO GET PROFESSIONAL FAST!! ALL THIS CLUMSY THIS AND THAT HAS GOT TO GO. Again I say that with kindness bro get it together and start getting paid big bucks!!! You are the only one on the whole internet that is showing this , I have searched and. Searched , one and only one other and it shows him cutting with a saw zall and he uses a bushing that he said got over heated, people are going to watch this and not come back unless you get your act together, instesd of making a whole video waiting on folks to ask questions why don't you do a video and tell us all about how you got started and all the ends and outs of putting a m660 on a China block I mean I have watch like 10 video and learned nothing but how to drop stuff and do stuff half way and wrong tools for the job just please don't get mad at me get it together!!
@eddiewilson3419
@eddiewilson3419 4 года назад
Your right man lol. I tried decking the cases and putting the 54mm chainsaw cylinder on mine but I’m stuck on the wristpin. I’m gonna drop down to the 52mm because it has the same 10 mm pin and hope I didn’t go to far decking because I want a engine without a spacer plate
@donaldellis9004
@donaldellis9004 3 года назад
@JERRY DINGLEBERRY I am convinced now
@gangsterbuilder
@gangsterbuilder 2 года назад
@@eddiewilson3419 use a 12x14x13 bushing instead
@cliffbradford4679
@cliffbradford4679 8 месяцев назад
It looked fine to me
Далее
Basic work saw porting tips
21:15
Просмотров 135 тыс.
stihl ms 660 on a motorised bicycle
22:27
Просмотров 9 тыс.
Brawl Stars expliquez ça
00:11
Просмотров 7 млн
The Gas Chainsaw Powered Railroad Impact Wrench
16:44
Просмотров 523 тыс.
TOP100 Woodworking Tools Hacks | Woodworking Ideas
1:39:21
Stihl MS660 investigative repair
32:26
Просмотров 20 тыс.
Weird 49cc Issues (Motorized Bike)
25:33
Просмотров 21 тыс.
4 handmade tools idea
16:53
Просмотров 1,2 млн