Тёмный

Dry And Wet Mode in Supercritical Boiler 

PowerPlant By BS Rathore
Подписаться 4,4 тыс.
Просмотров 4,5 тыс.
50% 1

Опубликовано:

 

30 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 17   
@lingarajpradhan
@lingarajpradhan 5 месяцев назад
Sir Very nicely explained. I will share with my colleagues.
@BhagwanSRathore
@BhagwanSRathore 5 месяцев назад
Thanks
@e-music3845
@e-music3845 Год назад
I looked for every video
@MrSomenath1986
@MrSomenath1986 Месяц назад
Why this parameter archive eco inlet feedwater temperature and high pressure heater outlet difference more than 10deg during wet to dry mode change over
@NarendraKumar-uk7wd
@NarendraKumar-uk7wd Год назад
This 660mw blr is made of BHEL OR SOME OTHER COMPANY?
@BhagwanSRathore
@BhagwanSRathore Год назад
Bhel
@desseado1234
@desseado1234 2 года назад
Nicely explained Rathore sir. One doubt sir . How to know which saturation temperature to check at separator outlet ? When we are slowly increasing the load of the boiler , pressure is increasing, so is the saturation temperature ? .
@BhagwanSRathore
@BhagwanSRathore 2 года назад
You can get saturation temp from the steam table or from your operating system which gives you sat temp wrt pressure If you increase the pressure the saturation temp will also increase accordingly till you get 221 bar at this point 373 deg c is the sat temp this is the maximum saturation temp of water or say critical point condition after this if you increase the pressure the saturation temp will always be 373deg c Case 1 Sep temp is less than or equals to saturation temp than water will rise in the seperator you need to control it by lowering feed water Case 2 if sep temp is very high compared to sat temp you need to give more water to maintain proper dT So if the separator is going down it means you are maintaining higher dt And giving less feed water And if the separator goes high it means you are giving more feed water than required Thats why we maintain greater than 17 deg c dT in dry mode so there should be no water present in the separator
@motive0507
@motive0507 Год назад
Sir,Could you please tell me about BMCR and TMCR simply
@motive0507
@motive0507 Год назад
Sir please explain this simply BMCR is maximum MS flow right? please tell me about TMCR
@BhagwanSRathore
@BhagwanSRathore Год назад
Boiler maximum continuous rating or the highest capacity of boiler to continuous steam produce Turbine maximum continuous rating is the maximum load capacity which is generally 10% higher than rated like for 660 mw unit it will be 660+10%
@gopikrishna.m8460
@gopikrishna.m8460 9 месяцев назад
sir, please explain feed water control loop, keeping in auto
@BhagwanSRathore
@BhagwanSRathore 9 месяцев назад
Please go through the playlist on the channel so you will find what u looking for
@e-music3845
@e-music3845 Год назад
Sir please make grade video in power plant
@BhagwanSRathore
@BhagwanSRathore Год назад
You mean grid?
@sudhirsingh3328
@sudhirsingh3328 2 года назад
Sir make a video on feedwater controller of super critical Boiler
@BhagwanSRathore
@BhagwanSRathore 2 года назад
Thanks for the comment i will try to do so
Далее
Ледник 1:0 Мужик
00:53
Просмотров 2 млн
Самое большое защитное стекло
00:43
Supercritical Boiler
14:28
Просмотров 52 тыс.
Motor Driven Boiler Feed Pump (MDBFP)
15:04
Просмотров 3,2 тыс.
SCB   Super Critical Boiler
4:01
Просмотров 39 тыс.
Boiler Water and Steam Cycles - Understand the working
16:01