Dspiae ES-P electric pen, portable, cordess, low speed, 3mm, grinder, drill, sander, polisher, tool

Подписаться 6 тыс.

Просмотров 10 тыс.

50% 1

Very compact and easy to use tool for the scale modeler. Internet says can charge to 80% in 30 minutes and fully charged in 60 minutes. Uses mainstream Dremel style 3.0mm tool bits.
Internet also says 5000/10000/18000 RPM but highly doubt it based on how slow it cuts plastic at the highest speed.
#dspiae #esp #grinder

Опубликовано:

23 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@MrFish1968 Год назад

I just bought one with the 9 bit set and also sanding disks, I build plastic model kits and I think that is where this will shine, especially as a nice paint mixer. Plus the 3mm shank makes is compatible with a massive range of bits for polishing sanding etc.

@briansrcadventures1316 Месяц назад

It's a shame it doesn't take various sized collets which would mean you could more easily use various sized shanked bits.

@jonflanagin6682 11 месяцев назад

Just bought it and i love it , so far so good.

@arclementsjr 8 месяцев назад

I also own this tool and on the main box it says the rpm at setting 1 is 5000, setting 2 is 10000 and setting 3 is 18000.

@RaNmA5886 Год назад

The bit Set ist very usefull, i Like it. You can Drill holes with the needle bit, but i would Like to have a Drill Bit for it. But i found nothing that fits. PCB Drill Bits are 3.175 and the Dspiae fits only 3mm Bits... Thanks for the Video, regards from Germany

@PeteCourtier 11 месяцев назад

Love mine but it’s a shame it doesn’t take 3.25mm shank bits! Had to buy a separate Chuck.

@Edward-Plantagenet 2 месяца назад

Any idea if this will take their tungsten drill bits. I suspect not.

@smallmodelcollector 2 месяца назад

@Edward-Plantagenet I've never bought the drill bits so not sure.

@joemoore4027 6 месяцев назад

Nice too ,but you only limited to using DSPIAE bit and acessorie's. Very limited selection. You can get a chuck to use other bits but they do not run true and break very fine drills. It's basically a small compact grinder.

@Wilett614 6 месяцев назад

You can Indeed get a "Precision" chuck to fit a 3 MM arbor . I made one : ) Works AWESOME especially when I need to Drill Small holes . I can fit ANY SIZE diameter tool in the collets up to and including .125 inch .

@tomcarrington1086 Год назад

Hi, thanks for the preview.. Where did you order the extra tools for it please? I have one and cannot find where to buy them. Thanks, Regards, Tom

@Kenyj5bv Год назад

Can you please confirm? Are the white spots (Example @12:00) on the body of the pen came from the factory or just dust/plastic particle? Thanks man!

@RaNmA5886 11 месяцев назад

Hi i have bought the 5mm sanding disk's and ITS make fun. You can sanding in small areas. Very usefull. It,s good to Sand Nub Marks down and get a smoth Finish. But i have 1 Problem. My Pen Draw Batterie Status very fast. I charge It at 100% and don't use it for 2 weeks...and the Akku was at 0%... It that normal? I try it 3 Times but every time the Same Problem...

@smallmodelcollector 11 месяцев назад

There's probably no battery management so maybe it slowly loses power like a car battery does. I use mine more often so haven't noticed anything wrong.

@blue2824 9 месяцев назад

Where do you get one?

@hernanrodriguez5082 Год назад

How long does the battery last fully charged?

@smallmodelcollector Год назад

No idea, sorry. Would depend how hard you grind too.

@hernanrodriguez5082 Год назад

@@smallmodelcollector thanks. Sorry but I was talking about when You storage it for a long time. Does the battery drain fast if stored for a long time?

@smallmodelcollector Год назад

@@hernanrodriguez5082So far mine has never been found dead after the months I've had it. I'm sure it loses power slowly like anything with an internal battery. I'd charge it every few months if you are worried.