DX6i Stick Calibration Procedure 

Thanks dude. All sorted. Lassie the rescue boat really for action! 😀

Just what I needed! My aileron setting of my DX6i was off a bit. Thanks for this great video.

I read an instruction but your video was easier to follow, thanks!

Great bit of info,This will help lots with the stick centre problem. I was wondering how to sort this out. Thank you for doing the video.

Still relevant in 2020 with my first gen 6i! Thank you!

Thanks for this video. Great presentation and information. I wish I knew this a few years ago, my DX6i had very poor calibration on all axes and I just gave up on it and bought a DX8 (which you can calibrate from normal menus) I'll dig out my DX6i and use it for the foamies now.

nice man. I had some problems with my potmeter, so I fixed that. but then it was of center like you had. now everything is alright again thank you!

Very clear, sound advice. Thank you.

Thanks bro still a useful video in 2021! 😁👍

Omg exactly what I was looking for! Thanks!!!!!

That was just perfect. Thanks! Georg

I know this is like old news probably... But anybody searching these videos.. learning how to calibrate their sticks... I should mention when you do this all your pitch and throttle curves... Travel adjust... End points ect should be at default settings... Otherwise on your monitor screen.. the arrows will be off from where they're supposed to be

1st thx for vid. 2nd, my DX6i looks exactly like yours- throttle a little up at the beginning of procedure and at the end. It is not because there's something wrong, it is because it is showing where your throttle is in relation to your throttle curve you set. I have one of my profiles set up for mcpx2, and the stock throttle curve from manual. At center stick it is up a little. When I switch to my linear 120SR profile, the throttle is directly in the center on monitor like it should be.

I was getting erratic movement around center stick and rudder was drifting to the right. Calibration sorted that out! Thanks

Good point. You should definitely set a linear throttle curve before doing this procedure. Having a throttle curve with the middle point off of 50% will definitely make the spot look off in the monitor at the end of the procedure. I'm not sure why you were getting error messages when you tried to comment to this video. Please rest assured that I did not block you. I think the discussion could be beneficial to someone trying to troubleshoot their DX6i.

No worries, it was a youtube issue. Yesterday a bunch of vids weren't working, then they did an hour later, today my comments are showing up with a big error message after I type them, but then go up delayed. I deleted the two other duplicates. Yeah so it is a good thing to know to set a linear throttle curve or at least know that if you don't the calibration will still work, but it may look "wrong" on the monitor. I cannot believe they didn't put this procedure in the manual though!

Great info...I subscribed!

Well done! Thank you Sir....

Worked perfect. This should be the first thing you do to a new controller.

thanks I had to do the opposite with the throttle cut , My Airlon is most likely no good, thought I give this a try. time to open up and see if swapping parts will fix.

Thanks Alot this Really help me!!

You are a life saver man! Why isn't this in the manual? Ugh

NOTE: this will work if you choose a 'un set-up' model on tour tx if you use a model that you've changed tho curve and duel rates it will show on the tx

Thank you!

Thanks. Helped me a lot :) :)

Fantastic thanks

merci pour ce tuto

Thanks you, Sir.

Thanks a ton.

it helped me too.

I assure you, my throttle stick was out of calibration. Setting a linear throttle curve was the first thing I did. I should have mentioned that a linear throttle curve should be set when determining the need for stick calibration. However, this calibration procedure is completely independent of model selection and throttle curves because it uses the raw inputs from the sticks. While stick calibration may not always be necessary, it will never hurt to re-calibrate the sticks.

I did the calibration when I turned Tx off when it was in the mcpx2 profile, if I did the calibration after I was in the 120SR profile (linear throttle curve), it would have shown on the monitor exactly center throttle when stick was in the center. Try that, or make a profile with linear throttle curve to try. Nothing wrong w/ your DX6i I don't think.. I did have a sketchy rudder center though, and this might fix it,I haven't tested it yet but it looks good in monitor.

Thanks I noticed while setting up my new Blade Nano QX that the Aileron was offset on the monitor screen and I was having to hold in rht aileron to counter that I believe.... aileron now shows as centered ok next recharge the Nano batteries and try flying again....Rgds...Laurie

Works with transmitter clones as well!

I was getting error messages when trying to comment, then a triple post happened. Anyway, if you do this calibration, and the last profile you had on the screen has a non-linear throttle curve, then the throttle monitor at the end of this procedure will be off exactly like yours in the vid. Mine looked the same was as the vid- throttle showed identical position. I had default mcpx curve set. It still worked fine though, the throttle monitor is perfect in a different profile with linear curve.

Right.. so you had a linear throttle curve set when calibrating in this vid? Just wondering. Mine looked the same (off center high) with non-linear curve set, but perfect with linear curve. It did help my rudder center instability though, which is why I had to do it in the first place.

If your stick shows off center on the monitor when you have a linear throttle curve set, then your sticks need calibrating and you would need to follow the stick calibration procedure outlined in this video.

How can I set an accessory switch? when I sart the transmitter wizard, it does not recognize any of the accesory sticks, it does recognize the gear channel but I already use that for my attitude/rate mode. Could you tell me how to set/setup an assecory stick on my Dx6I?

would doing this cause issues with the programming of a cp heli?

Followed instructions to a "tee". Works fine except for the ELEV channel which stubbornly will not center even after repeated attempts. What am I doing wrong? Thanks.

Good video, but I think something is missing: this was not working for me until I went into sub-trim (in the Adjust List) and set everything to 0 before doing the calibration (also don't forget to set a linear throttle curve). If you don't the final calibration will be off.

When I perform this. My throttle elev and aileron all move together. Like their mixed. Of course I did not reset my models.

@Rich Huff My throttle ,ele and aux are fine rest is out even after following yours and another video . . .whats ch5 for ?

If your end points are NOT off wouldn't it be a sub trim, travel adj, throttle curve, or mix, ect. problem/issue that is making your center off? Or am I missing something here? I have had my END points off a little in the past which needed calibration, but if I ever had center off it was always something I did during setup. Not saying it isn't a problem that can be fixed by calibrating. However being in the hobby since I was 15 " now 29" I never had a problem like yours...? I hope it worked out for you! As I am sure you know recalibrating your sticks without having a new "reset" model can/will mess up any future programming on every model you program in said TX. After calibration I would recommend re-binding every model in the TX as any mixes/settings you have fine tuned on any model prior to calibrating could be off a little or ALOT causing problems. Happy Flying!!!

what if my low for rudder reads 000

Followed the vid to the letter and its worse,think I've got a issue with my tx