Тёмный
No video :(

Epic 6-Hour CNC Electronics Retrofit Crushed into 14 Mins: The Ultimate DIY Overhaul! 

BuildYourCNC
Подписаться 101 тыс.
Просмотров 2,6 тыс.
50% 1
ВидеоПоделитьсяСкачатьДобавить в

I show a typical CNC electronics retrofit.
Official Link:
buildyourcnc.com/
If you need help with your CNC electronics, get in touch with us at Buildyourcnc.com
Wire Stripper I mentioned in the Video (Hard to Find):
amzn.to/3OiAncF
Check out some other tools and equipment I recommend:
www.amazon.com...
I may receive a small commission from the Amazon links.

Опубликовано:

 

28 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 19   
@PatrickHoodDaniel
@PatrickHoodDaniel 7 месяцев назад
Thanks for watching. Let me know what you think.
@soniclab-cnc
@soniclab-cnc 7 месяцев назад
LOL. that giant linear power supply. Big ol toroidal transformer. There are two schools of thought on the linear vs switch mode power supplies... I won't start a spitting match over it. And yes I always use wire ferrules. You just have to take the time and make sure they are fastened down well. I have had issues with bare wire connections and very few when using wire ferrules. For low voltage stuff they are fine.
@PatrickHoodDaniel
@PatrickHoodDaniel 7 месяцев назад
God, the toroidal transformer is HEAVY!! I would use switch mode just for that. By the way, I don't mind the discussion on the supplies as it helps the algorithm. Thanks for the input on the ferrules. Let's keep that discussion going too. Haha.
@jonathanjoffe751
@jonathanjoffe751 7 месяцев назад
Oh ha this is mine. Got like 2/3 through the video before I realized.
@PatrickHoodDaniel
@PatrickHoodDaniel 7 месяцев назад
It's actually not. The components are very similar. You'll see that I say that the customer did not provide the motors, but you did.
@PatrickHoodDaniel
@PatrickHoodDaniel 7 месяцев назад
Your cabinet will be much nicer too because it will be brand new. The cabinet that I'm showing in the video is the customer's cabinet
@jonathanjoffe751
@jonathanjoffe751 7 месяцев назад
Oh derp also I didn’t send you an Ethernet smoovestepper. I’ll get you the machine dimensions this weekend.
@jonathanjoffe751
@jonathanjoffe751 7 месяцев назад
Oh derp also I didn’t send you an Ethernet smoovestepper. I’ll get you the machine dimensions this weekend.
@jonathanjoffe751
@jonathanjoffe751 7 месяцев назад
Oh derp also I didn’t send you an Ethernet smoovestepper. I’ll get you the machine dimensions this weekend.
@joecnc3341
@joecnc3341 7 месяцев назад
Tremendous cost and space reduction with modern components! Each one o those gecko drivers were $200-$250 "Back in the day"
@PatrickHoodDaniel
@PatrickHoodDaniel 6 месяцев назад
I know! They are great drivers.
@dineshm4582
@dineshm4582 7 месяцев назад
Where can I buy this
@PatrickHoodDaniel
@PatrickHoodDaniel 7 месяцев назад
Buildyourcnc.com
Далее
CNC Electronics for Customer Using an Avid CNC
33:00
CNC Electronics for Customer Using an Avid CNC
Просмотров 57 тыс.
Your CNC Electronics are NOT WORKING. How to diagnose!
20:33
Your CNC Electronics are NOT WORKING. How to diagnose!
Просмотров 8 тыс.
Купил? Страдай! - 2 года боли и украденный Утиль!
47:17
Купил? Страдай! - 2 года боли и украденный Утиль!
Просмотров 96 тыс.
МЕНЯ НАКАЗАЛИ ЗЛЫЕ РОДИТЕЛИ - SCHOOLBOY RUNAWAY В РЕАЛЬНОЙ ЖИЗНИ!
11:51
МЕНЯ НАКАЗАЛИ ЗЛЫЕ РОДИТЕЛИ - SCHOOLBOY RUNAWAY В РЕАЛЬНОЙ ЖИЗНИ!
Просмотров 510 тыс.
Губин вернулся? Творческий вечер певца
00:40
Губин вернулся? Творческий вечер певца
Просмотров 171 тыс.
ТЫ БЫ НИКОГДА ТАКОЕ НЕ ЗАГУГЛИЛ #18
32:38
ТЫ БЫ НИКОГДА ТАКОЕ НЕ ЗАГУГЛИЛ #18
Просмотров 1,8 млн
Watch Me Build Closed-Loop CNC Electronics in 25 Minutes
32:06
Watch Me Build Closed-Loop CNC Electronics in 25 Minutes
Просмотров 103 тыс.
CNC Router Controllers Built Incorrectly (Volume 11)
26:16
CNC Router Controllers Built Incorrectly (Volume 11)
Просмотров 1,4 тыс.
This Oscilloscope Is Garbage (Literally)
16:59
This Oscilloscope Is Garbage (Literally)
Просмотров 947
LinuxCNC EtherCAT for reals this time - New Control Cabinet and Leadshine Servos
24:09
LinuxCNC EtherCAT for reals this time - New Control Cabinet and Leadshine Servos
Просмотров 82 тыс.
How Giant Drill Bit Is Made? Mass Production Process Of PDC Drill Bit
26:19
How Giant Drill Bit Is Made? Mass Production Process Of PDC Drill Bit
Просмотров 10 тыс.
Centroid Acorn CNC Retrofit Complete
10:04
Centroid Acorn CNC Retrofit Complete
Просмотров 10 тыс.
Build Your Own CNC! (Part 1) - Hardware
27:47
Build Your Own CNC! (Part 1) - Hardware
Просмотров 1,3 млн
Let's Demystify the ATC Spindle! Part 1: Introduction
8:00
Let's Demystify the ATC Spindle! Part 1: Introduction
Просмотров 11 тыс.
DIY: Cyberdeck multi-function backup computer
29:31
DIY: Cyberdeck multi-function backup computer
Просмотров 3,8 млн
LARGE 3D PRINTED CNC FROM SCRATCH
17:25
LARGE 3D PRINTED CNC FROM SCRATCH
Просмотров 414 тыс.
Купил? Страдай! - 2 года боли и украденный Утиль!
47:17
Купил? Страдай! - 2 года боли и украденный Утиль!
Просмотров 96 тыс.