Тёмный

eSun eBOX Lite 3D printing filament dryer 

PS After Hours
Подписаться 4,5 тыс.
Просмотров 11 тыс.
50% 1

eSun eBox Lite bit.ly/2WbWtFR
Some filament types, like TPU or Nylon, absorb moisture. It's bad, because when the filament is heated up into the printer's nozzle, water evaporates, bubbles up, and negatively affects the final results. This is why some filament types have to be kept dry and dried from time to time. eSun eBox Lite acts as a filament box with an integrated drier.
www.esun3d.net...

Опубликовано:

 

16 сен 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 11   
@olafschermann1592
@olafschermann1592 Год назад
I use the heatbed covered by a cardboard box to dry filament occasionally. Small holes on the side/bottom and top center create some convection where the moisted warm air can escape and fresh cold air comes in and dries by heating. Heatbed is pretty good heat controlled and amazon brings me free cardboard anyway 😂
@religionisapoison2413
@religionisapoison2413 Год назад
Does the stuff kill you without ventilation
@olafschermann1592
@olafschermann1592 Год назад
@@religionisapoison2413 i don‘t know any filament for FDM printers that produce fumes. As you see some dry it in the oven. Resin printers have unhealthily fluids.
@religionisapoison2413
@religionisapoison2413 Год назад
@@olafschermann1592 ok cool, thank you 👍 good point
@Haych_Q
@Haych_Q Год назад
Just ordered one of these yesterday
@GreyDeathVaccine
@GreyDeathVaccine Год назад
I bought it a few days ago. Saturday off and I'm going to start testing. BTW. I guess by your accent you're Polish? I'm right? If so, pozdrawiam 🙂
@grzbiet
@grzbiet Год назад
slickdeals has deal on a two rolls filament dryer from "comgrow" today and that video was a sign that I need one - it is a jungle down here in florida, even in winter I have 70% humidity inside. in the summer it's 50-60% as we get giant dehumidifiers with every house and apartment. outside is hard to breathe for the newbies. and what's the humidity in northern home nowadays? my drybox with silica gel is 30%... btw Paweł, did you ever research the peltier cell filament dryers?
@nokomentsEVH
@nokomentsEVH 8 месяцев назад
Can you print directly from that dryer?
@PSAfterHours
@PSAfterHours 8 месяцев назад
yes, yes you can
@BBFPV
@BBFPV Год назад
Even pla breaks between roll and extruder with time. I put it in a big box with all the granulate i have.
@rjung_ch
@rjung_ch Год назад
👍
Далее
Are these Filament Dryers Worth It? Again.
24:23
Просмотров 27 тыс.
УГОСТИЛ БЕЛКУ МОРОЖЕНЫМ#cat #cats
00:14
Testing eSUN eBox filament dryer - unboxing and review
22:44
Lightweight 3D Printing - eSun ePLA-LW
7:41
Просмотров 1,9 тыс.
eSUN eBOX Lite 3D Filament Dryer Box
0:31
Просмотров 3,2 тыс.
DIY 3d printed electric motor
0:33
Просмотров 9 тыс.
What's the BEST open source license for your project?
8:43
Can you sell a GPLv3 software?
0:48
Просмотров 288
The Surprising Truth About US Measurement Units
0:43
Просмотров 2,5 тыс.