Love your videos. Your skill and creativity are awesome. I can’t help but wonder though how incredible your projects would be if you spent more time and attention on them. Keep up the good work
Olhe a profissão de Jesus Eu admiro muito está profissão porque tem um mundo de possibilidade, este não tem só uma profissão,mas é um verdadeiro artista ,verdadeiro artesã. Parabéns , hoje eu me arrependo porque não negociei uma marcenaria com todos os maquinários , minha filha até me chamou atenção. Mas fiquei com medo de queeus d lhos não iriam querer trabalhar com isso ,se eu TIVECE certeza eu teria negociado pois era barato . Parabéns você é muito bom Noque faz e caprichoso Também se vê que faz com carinho mesmo e muita dedicação. Deus te abençoe sempre.
Maybe there were some parts missing from the video where you measured, or maybe you've built this particular item so many times that you know it by feel, but you made this look effortless.
As a person that has done woodworking I say that this piece is AWSOME. As a homemaker this piece is a nightmare to try to dust. My stick and ball furniture is a nightmare as well
Obvioiusly by a carpenter not a furniture makier. Yes interesting bent wood effects, but the wood is not fine furniture wood. The screws are just driven in all over the place, and let visible. Theres apparetntlly no care taken to see that the screws are hidden. And there are pins (nails) visible all over the place. Yes, nice bent wood effects, but the rest is pretty slapdash and finish is mediocre.
Yep, it’s only a matter of time before he loses a finger, and pushing on the wrong side of the cut, he’s going to get it in the head someday. I hope I’m wrong.
Где? Чем? Зазорами? Трещиной в основании? Кривым внешним кольцом и браком на первом кольце? А может нарушающей технологию фиксацией на саморезы и степлер?
@amazing A to z🤣 if you say so, I built furniture and cabinets for years. Why would you ever use a pen that leaves a permanent mark, especially on furniture that is probably going to be stained?
I use a pen. It has a finer and more consistent line than a pencil. I also use a marking knife. And I use a pencil for certain things like marking a surface before sanding.
Hi. What type of wood did you use for the bent lamination? What was their thickness and width? This might work out to solve a materials problem for a project for my son's girlfriend. Thanks
Hello there Bob, I don't know if you're in Britain or America, but that doesn't really matter, because the woods I'm going to recommend you as a cabinet maker can be found in bothe of these countries. First of all, there are two very important factors to take into account: Thickness of the strips (I live in France, so we work in metric measurements). The ideal thickness should not exceed 3mm (millimetres, about 1/8") Grain direction of the original plank. The grain should be as straight as possible. Avoid knots. The method used above has its weaknesses. Cutting thin strips between the blade and the guide tends to overheat the strips and therefore twist them. It's far better to cut the strips on the other side- you can clamp a short block to butt up to after every cut. By cutting the strip as an offset there is no heating. It's much better to plane the edge of the plank after every cut. so you're using two machines, but getting a much better result. DO NOT sand the strips like what's shown above; it rounds the edges and creates horrible glue joints. The two ideal woods are Beech and Ash. Other woods may work too (Maple/Sycomore, Birch, and some others). You have to do some trials. Also steaming is ideal, or at least wetting. Keep in the mould for as long as possible- preferably several days. Good luck. I hope this has been of some use to you? Greetings from France
Потому же, почему у него адские зазоры, трещина в первом кольце, дефект самого большого кольца, трещины в ножках, неправильное свинчивание и брак в нижней платформе. Ему просто пофиг. Ролик снял, скорость х2 забацал и в продакшен. 400к просмотров на пустом месте, а стол после съемки в утиль.
2 дня работы из которых 1,5 дня сохнет клей, реально браво, а ещё он забыл в видео упомянуть что древесину на круги распаривал, для человека который работал с деревом это очевидно ибо цвет сильно разница с изначальным, тут много нюансов, но в целом за ручной труд всегда надо благодарить, но за мастерство 3 с минусом, неточная подгонка деталей, зазоры в мизинец толщиной, засверливает неграмотно древесину, повезло что нигде не лопнуло либо на видео не попало, нижняя платформа с дефектом, как и ножки, потаи замазал просто коричневой шпатлёвкой, даже без попыток шлифануть. это не мастер, это уровень разнорабочего в столярной мастерской.
@@user-io6lh4vp8d сверху и правда бы круглую столешницу из стекла, вот тогда можно было хотя бы что то поставить, а так не понятно зачем это дырявое нужно!?
@@MidiMan0. вы не только видео до конца смотреть не можете, но и читать похоже не особо умеете, может хоть в цифры у вас получится 18:00 посмотрите внимательно, или стекло на столько чистое что на экране не отображается?
@@user-io6lh4vp8d а толку мне смотреть до конца? я и так вижу что это что то непонятное я даже смотреть его до конца не буду, но факт остается фактом, что туда нужно стекло, хлть квадратное хоть круглое, но желательно круглое конечно! потому что стол сам круглой формы, но если бы стол был бы квадрата то можно и квадратное стекло, но тут уж кому как!
