F100 - Fuel Injection Conversion

Подписаться 21 тыс.

Просмотров 35 тыс.

50% 1

In this video I walk through the process and reasoning behind adding an in-tank fuel pump to my restomod F100 project. I installed an Aermotive Phantom Stealth 18688 fuel pump into the 1970 mustang tank, that is installed in the rear of my F100.
1969 F100
Links:
Aeromotive Phantom Stealth 18688 fuel pump hanger kit
amzn.to/34rMHjU
Ebay Walbro 450:
www.ebay.com/itm/GENUINE-WALB...
-6 AN Fuel line kit:
www.ebay.com/itm/Braided-3-8-...
-8 AN Fuel line Kit:
amzn.to/2WvF1sx
Holley fuel pressure regulator
amzn.to/2KbCzoJ
Fuel rails
www.ebay.com/itm/Z897-LS1-LS6...
Aeromotive 10 micron fuel filter
amzn.to/2WvUXuW
Aermotive fuel pressure gauge
www.jegs.com/i/Aeromotive/027...

Авто/Мото

Опубликовано:

18 дек 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 85

@nitcat1 3 года назад

Nice. Watching you do this reduces the intimidation factor a lot. Thanks.

@330_garage3 3 года назад

Glad it was helpful! - Makes the editing time and the video work worth it, when you guys let me know your car or truck is running again, because of my RU-vid posts!!

@stevemoody6928 3 года назад

I don't own an F100 or even have any plan to buy one, but I ended up watching a bunch of your videos. Very informative and I like how you talk through your troubleshooting and solutions

@duanebennett2961 3 года назад

Man that looks great!!! Can’t wait to hear it run!!

@330_garage3 3 года назад

You and me both!

@HattemMorse 3 года назад

Awesome man! Been looking forward to a new video!

@martinmayhem7122 3 года назад

Another great video Rob - I really enjoy how you describe everything and show us how you make these parts work properly in your design and application here. I think this setup is great, and I have been planning to use the Holley Sniper Returnless Retrofit Fuel Module and Sniper throttle body. Only because of the natural aspirated 428 CJ setup in my 67 F100. Your setup is going to work great with the LS, and setup properly for boost - when you need more fuel and pressure! I really like the Aeromotive setup with the foam installed in the tank. Merry Christmas man. Glad to see you're inspiring others. Keep up the great work! Enjoying your F100 build!

@330_garage3 3 года назад

Nice thanks for the great compliment! Glad you are enjoying it, and sounds like you have a pretty killer setup yourself with that 428CJ! Merry Christmas!

@julianrodriguez1768 3 года назад

Yes! Been waiting for a new vid! Welcome back 🙏

@330_garage3 3 года назад

More to come!

@davidrobinson5943 3 года назад

Great job installing that fuel system can't wait to hear that Ford come to life thanks for sharing your content

@slow5oh89 3 года назад

@@davidrobinson5943 Won’t be a ford coming to life 🤣

@davidrobinson5943 3 года назад

@@slow5oh89 yep your right 🤣

@Snakez011587 3 года назад

Getting closer and closer :) looking great so far. I'm letting this channel be my motivation for my truck, but hopefully I can stop myself after the 390.

@330_garage3 3 года назад

hahaha I really liked that 390, I would think with some good brakes and fresh suspension you would have a fun driver! Glad its motivating you guys!

@Snakez011587 3 года назад

@@330_garage3 it's going to be such a sick truck. Looking forward to the next video. Have a merry Christmas!

@rjw8840 3 года назад

Hope your all good ! Waiting in your next video 👍🏻

3 года назад

Nice fuel injection conversion on your F100.

@yarkie1 3 года назад

Can't wait to see this thing fire up!

@330_garage3 3 года назад

You and me both!... also makes me a little nervous haha

@yarkie1 3 года назад

@@330_garage3 you got this. Just by your videos, I can tell you're detail oriented. I'm sure it'll be fine.

@chalolmeza5615 3 года назад

Cant wait for another video

@frankm8533 3 года назад

Can't wait to hear this run

@330_garage3 3 года назад

haha you and me both! Hopefully that pieced together motor doesn't just blow up

@frankm8533 3 года назад

@@330_garage3 I have faith in ur work it will run excellent

@jimmypenrose4553 3 года назад

Great video

@330_garage3 3 года назад

Thanks!

@keithharden7844 3 года назад

I can't believe he's only got so few subscribers. He needs to grow.

@330_garage3 3 года назад

thanks!! I've only been at this for a year... and don't have ton of videos out yet... its growing! We're up 1300 subscribers this month!

@charlesgayhart6463 3 года назад

Lovin your channel... I’ve seen other videos saying that you should run your feed line straight to the rail and to your regulator after the rail.. I’m not sure if it matters but it might be worth looking in to...

@330_garage3 3 года назад

Thanks! Yeah I have seen guys set them up all different ways. If it becomes a problem, I don't think it will be hard to change. I spent a few hours reading arguments on the LS1Tech forum... and decided to set it up where the regulator feeds the rails.

@BrittneyShaver 2 года назад

Hey Rob, great series of videos. Your truck is probably completed by now and I’m sure you’re enjoying the heck out of it. I’m working on a ‘65 F100 and plan on using a lot your ideas on mine. So why did you choose not to use the Aeromatic fuel pump that came with the kit?

@11TreyHenry11 3 года назад

Great video! Happy to see I’ve done basically the same thing. Weird question on the mustang sending unit. Did you just extend the orange wire from the original tank to it and make your own ground? In cab sending unit had a ground but there’s no place on the mustang one for a ground wire? Haven’t tested to see if it works yet but would like to know before I go back on with the bed

@330_garage3 3 года назад

I ran a wire from the new mustang sending unit (same resistance 10 -80ohm as the original F100) to the cab and connected it to the orange wire that went to the original sending unit. The mustang tank seems to be well grounded to the frame, so no need to add that additional ground wire. I measured resistance from the new sending unit stud, to the frame, and saw 10 ohms with a full tank. Works well with the factory f100 gauge!

@Dieselfumes1982 3 года назад

Well shit I just subscribed you got me. I do have a 1970 short bed my 11 year old and I are ready for us to restore.

@germancorcesbohmer2307 Год назад

Hey Rob, how are you? wich gas tang form aeromotive do you mean? do you have the link? i want it for a coyote swap

@dreamingcode 3 года назад

How did you get the truck bed off? Did you do it by yourself?

@REVNUMANEWBERN 3 года назад

Look I have carbed 65 F100 with a 5.0 , currently I have a Holly HLY-12-810 thats just bolted to my frame close to the stock tank IN the cab, will this electric frame mounted pump I have now pull the fuel from a rear mounted tank like yours???

@330_garage3 3 года назад

Sure it will. You would just need to extend the pick up line (feed line) to the rear of the truck.. and a return line if you are running one. But it would work just fine

@justinsquires5998 2 года назад

Did you have any issues with the foam breaking down?

@justincarson5140 3 года назад

Where did the vent terminate? I have everything run like you but don’t have any ideas on the vent plumbing:)

@330_garage3 3 года назад

hahaha good question. I just ran it back under the hood for now.. I need to find a charcoal canister or something to vent it through. I'm afraid its going to smell like gas in the garage. And I'm not sure if technically (legally) its supposed to have a roll-over valve in the vent line?

@kenwilson2315 3 года назад

Nice job! Cannot wait your next one. Where 'ya been?

@330_garage3 3 года назад

great! Just taking me longer than expected to get these videos edited and put together...

@s3w349 2 года назад

I know the video was done awhile ago but I will ask anyway. The fittings look like they stick above the frame. Any problem with the bed fitting flat?

@330_garage3 2 года назад

I'm still here haha, The bed floor braces that sit on the truck frame, raise the bed floor off the frame an extra 1.5" and give you clearance

@s3w349 2 года назад

@@330_garage3 good to here. Makes sense. I have a lot to learn lol

@keithskustoms2311 3 года назад

LS? What happened to the 390?

@chuckalexander987 3 года назад

what was done with the vent hose? Does a valve of some sort go on the end? Mounted were? Thanks! And keep on the good work . Enjoying the project.

@330_garage3 3 года назад

I just ran the vent back to the engine bay, I need to figure that part out, maybe run it through a charcoal filter so it doesn't stink up the garage.... I think it may legally require a roll-over valve in it as well?

@ryano425 3 года назад

Any chance you live close to NC? Have an F100 that is in the middle of this all being done to it and the guy doing the work decided he is retiring from the restoration business. Would be awesome if you wanna take the rest on?

@330_garage3 3 года назад

No.. I'm actually in Texas. I just do this for fun on the side, I have a 9-5 job that gets in the way of my fun already.

@serrgmtz 3 года назад

Hey I'm doing an LT 5.3l 8l90e swap and on my f100 fuel system can be tricky with these new engines

@330_garage3 3 года назад

Agreed post some videos! I want to see this 5.3 swap!

@scootertipton8211 3 года назад

Hey man you still got the old dream beams from your old lowering kit before the crown vic swap??

@330_garage3 3 года назад

No, I never lowered the front. I only lowered the rear of the truck. I do still have that rear lowering kit, I put it back in the box when I did the 4 link.

@scootertipton8211 3 года назад

@@330_garage3 interested in. Getting rid of anything let me know

@leviecameron9422 3 года назад

Why didn’t you put the pump Assembly on the right side which is the low side of the road?

@330_garage3 3 года назад

I make too many fast right hand turns? I don't know haha

@edsyphan3425 3 года назад

Re: The bed mounting video. It's too late now,,,, but the spring hangers and 5th wheel mounts on big trucks use some sort of giant nut sert in the frame.

@harrygrimes8650 3 года назад

Hey did you already sell your 3 speed from the 360? If not I would be super interested in purchasing it from you!!

@330_garage3 3 года назад

I did. I sold the 390 to fund this next phase of the project. I sold the trans, and mounts with it. Sorry man

@harrygrimes8650 3 года назад

@@330_garage3 nah man don’t worry about it. Thank you so much for replying tho!!! I love your videos and I’m excited to watch your project!

@anthonymcclelland9315 3 года назад

Need more videos

@330_garage3 3 года назад

I'm working on them.. just takes me a while to get them all cut and edited.. glad you guys like them!

@Shadetree_Mechanic 2 года назад

Tanks Inc sells a 1969 Mustang Fuel injection Tank

@AldanAmerican 3 года назад

Hello! Would love to get in contact with you for a project, please let us know the best way to message you.

@dshipp8931 3 года назад

Where did you terminate the vent line?

@330_garage3 3 года назад

hahaha good question. I just ran it back under the hood for now.. I need to find a charcoal canister or something to vent it through. I'm afraid its going to smell like gas in the garage.

@dshipp8931 3 года назад

@@330_garage3 yeah I bought the hyperfuel in tank for a carburetor applicant. It almost looks like it vents itself. Not really sure can't find info on it.

@alecfarmer1413 3 года назад

I paln on doing cv swap 8.8 4link. Could you recommend a 110v mig, or do you think a 110v mig can do this kind of work?

@330_garage3 3 года назад

Yeah quite a few of the 110v machines will do 3/16" steel in a single pass. Plenty for doing a frame, etc. Check out the Lincoln Weld Pak 140 HD MIG Wire Feed. 140amps will weld a project like this just fine. The duty cycle gets pretty short when you run them at full power like that, so you have to weld a little, and let the machine cool. But it will do it.