First Project BT30 ATC Spindle on my DIYCNC

Подписаться 773

Просмотров 17 тыс.

50% 1

DIY Aluminium CNC
HGR20 Rails with HGH20CA Z1 Blocks on all Axis
C5 SFU1605 with Dualnut on all Axis
4,5kw BT30 ATC Spindle with Fuling VFD
Nema 23 CL Stepper on all Axis
LinuxCNC Probe_basic with Mesa 7i76e Ethernet Card
Amazon Wishlist: www.amazon.de/...

Наука

Опубликовано:

21 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 29

@mystamo Год назад

Been following your videos. Anticipating my MR1 machine from Langmuir.. Getting excited.. Your machine is pretty stout. Love the new spindle.

@cnc_andi3294 Год назад

Thank you i´m working for much more Stability

@ewildgoose Год назад

Very nice design! (Out of interest, does it get red hot with a candle in it?!)

@cnc_andi3294 Год назад

No, works fine with a candle.

@AustinNicholson-jn9wu Год назад

Need to tram it or something.

@bonsaicnc 8 месяцев назад

sehr sehr nice! was waren das für schnittdaten beim planfräsen? thx

@cnc_andi3294 8 месяцев назад

müssten 10000rpm gewesen sein bei 1500mm/min.

@carlosmeale5746 Год назад

show de bola 👍

@bjornbambus8859 Год назад

Stell die Messer des Messerkopfs mal in einem leichten Winkel zur Werkstück Oberfläche, also nicht parallel. Dann sollte die Oberfläche etwas schöner werden.

@cnc_andi3294 Год назад

Falls es funktioniert. Werde es testen.

@bonsaicnc 8 месяцев назад

wie genau meinst du das? sry wenn es eine DAU Frage ist, bin aber Hobbyist

@bjornbambus8859 8 месяцев назад

@@bonsaicnc die Schneide nicht parallel zum Werkstück sondern mit einem Kleinen Winkel, ähnlich wie bei Fischschwans Fräsern, nur nicht so stark.

@egemens Год назад

what is your probe brand/model? I'm looking for one.

@cnc_andi3294 Год назад

DIG3DLPM

@dzot43 Год назад

can u link on AliExp or ebay the 1st face mill in video?

@cnc_andi3294 Год назад

Hello please see at my another videos (comments).

@besssam Год назад

Hi, I have a very similar setup, what was your feeds and speeds please for the fly cutter and 2flute?

@cnc_andi3294 Год назад

Hello, for the Facemill i´ve used 10000rpm, 2000mm/min and 1000mm/min for finish. for the 10mm 2 Flute Endmill i´ve used 16000rpm at 2700mm/min Feedrate for finish i´ve used 24000rpm at 1500mm/min.

@besssam Год назад

@@cnc_andi3294 Geez, are you running AC servo motors ?

@cnc_andi3294 Год назад

@@besssam now im using dc nema23 cl stepper motors

@besssam Год назад

@@cnc_andi3294 interesting, I use those also. I have been been ultra conservative fearing if the motors loose step. Perhaps I should dial up a little. right now the max feed is 1200mm/min

@cnc_andi3294 Год назад

@@besssam You have to try that, I don't know your machine. But normally there is more to it than that. I have 6000mm/min. in G0. Operate the motors with a 36V power supply. But it also depends on your machine