I have iphone xr locked with icloud and i change just motherboard 128gb and is working very well but the problem is the face id is not working bcs i change logic board and i put a new one so it will work if i do the same process in the video to fix that Face ID Thank You
What was the original problem with the projector that was fixed by the tag-on flex cable? If the projector is damaged, how can that be fixed with the Tag-on Flex cable?
exactly that’s my question, what does a fused dot projector actually mean, there’s no work done to the dot projector for this repair so it means there’s nothing physically wrong with it? the tag on flex just somehow bypasses some check the phone does?
So when I’m trying to repair a Face ID. I follow these steps: 1) plug in flex, plug 108 into computer 2) hit test: everything says abnormal except NTC & I2C, they say normal 3) then I hit back up, that’s successful 4) plug a108 into power 5) then I hit activate, the process starts then I get a message that says: “Abnormal, please remove extension flex cable, or use chip to repair” How do I resolve this issue? Is there a support forum ?
Если я правильно понял ,то эти товарищи подают на проектор точек ток чтобы отгорело то что ушло в замыкание ,а потом через шлейф-обманку имитируют нужное сопротивление .
Нет, просто есть цепи с высоким напряжением, на программаторе нет стэп ап преобразователя. Либо память размещена в одном корпусе с микросхемой требующей 19-24 вольта, что применимо к подсветкам , коей и является дот проектор. Для чего нужен таг он ? Для того же, для чего и подобный шлейф при замене батареи- подменять данные на шине, что якобы фокус не имеет проблем.
what if i replace the whole set face id with new and i miss place the original parts of face id can we still fix it without the original which is broken and missing or misplace?😊
Ok, I just bought RP30 and there is no " High Voltage Power Cable". What voltage this should this be? Also "Snap the dot projector cable to the programmer" is missing, I have only a cable that needs resoldering. Please advice!
My iPhone 12 Pro Max has a face ID problem on the True Depth Camera section, and my portrait front photo can't be used, can I solve it this way or do I have to use a wire jumper on the Mosfet
The solution is available to most programmers now. In this video, we use the REFOX RP30. shop.rewa.tech/detail/refox-rp30-multifunctional-restore-programmer-for-iphone.html
Afaik it's a bypasser, the charge gets through and communicates with the PCB the health and cycles, preferably 100% and 0 respectively. It's a solution for refurbish shops.
@@rewatechnology2008 the link to the add on board doesn’t have the high voltage connector as shown in the video. I have refox programmer. I just need the add on card shown in the video . Please, send the link
@@krantikoganti Hi, the high voltage connector comes with the extension board. Since you have the REFOX programmer, all you need to purchase this time is the extension board and respective tag-on flex cables.
The solution is for fixing dot projector fusing problems. What you described is mostly the broken earpiece speaker flex during screen replacement. In this case, the only solution is to change the flood illuminator flex cable. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-bJCuMFeUiGU.html
Can someone explain the actual cause of the fused dot projector? how does this happen? does apple just randomly disables the dot projector? by looking at this repair it looks like the there’s nothing physically wrong with the dot projector and the tag on flex just bypasses the check apple uses to disable the dot protector?
Due to the high sensibility of the sensor and the all camera module in general, it can break very easily if the phone drop on salty water or from high heights
@@Saleh94S cause the data where stored into the cable, before this metod the only metod avaible was micro-soldering the old cable on the new face-id module, btw you can repair the face id only if the dot projector cable work
@@Saleh94S sure, open the camera and go to potrait mode on front camera, if the square become yellow, the dot projector work, or a second way is : go to front potrait mode and with a second phone open the camera and aim to the notch if you see a red light beside the front camera ( on the notch) the dot work, but just the cable without opening no im sorry
Sir, I have many problems with data connection on my phone, just restart the data, but when I turn off the data, the data does not turn on, but why phone model samsung s10 Greetings from Bangladesh
REFOX RP30 must work with the extension board and respective tag-on flex cables to fix the dot projector problems. For detailed info, please check the below link. shop.rewa.tech/detail/refox-rp30-multifunctional-restore-programmer-for-iphone.html