This timer is only suitable for light loads,if we are connecting to motor and some other windings,in a few days has to be damage automatically...am i correct?
Hi, It's works after cleaning inside. Actually when we apply Heavy load on it,the connector of the relay sparks while switching. so i removed this relay cap ,and clean those touching points and now its working fine
C2= 10uF 60V electrolytic cap, R2=471K metal oxide resistor, R4=150ohm +-1% May I ask why these specific components? I'm also looking at fixing a busted up timer- the video didn't work for me.
Same case with me also.Displsy is not woking even after putting a new battery.Time is working with a shift of 30 minutes.Not able adjust since diplay is not workig.Will be thankful sny guidance
Could you please share which of the two capacitors- there are two C1=0.47uf box type and C2=10uF electrolytic one. However on visual inspection, both hasn't busted or anything. To share the service life- the timer is less than one month in service with twice daily one/off for a min- could the capacitor have gone bad this fast? Tapping the relay didn't work for me either.
Sir, timer switch is working, but the light is not glowing, what is the reason, can it be rectified, if so kindly give me the contact details, so that i will send it thru courier, i will pay the repair cost.
Sir, the timer switch on and off is working, but light is not glowing, can it be rectified, if so pl give contact no. So that i can send it to you for repair, cost will be born by me
I have 3 pcs of frontier auto timer switch’s Wich is out of order Automatic is not working used only few days please anybody should give me the address and email for the frontier company my email tibasheer@gmail.com
What to do when this timer changes its time by its own...and sometimes when I set a clock...it resets that time again from 00:00:00 .. what could be the reason.. wiring is proper.. this occurs at 3-4days and I need to reset it
@@omarmuhammedsanju do one thing order new one and return the old one under the same order.this is only the way.. frontier never give the warrant.. lots of people facing same issue..
Please check incoming signal from driving transistor on PCB,which is goes to relay , if there is no sufficient voltage then its can't trigger the relay.If the the transistor is OK , then Clock chip may became faulty and fail to deliver signal to relay. Thanks for your comment. *Please press manual Relay active switch while checking relay input signal. कृपया पीसीबी पर ट्रांजिस्टर से आने वाले सिग्नल की जांच करें, जो रिले में जाता है, यदि पर्याप्त वोल्टेज नहीं है तो यह रिले को ट्रिगर नहीं कर सकता है। यदि ट्रांजिस्टर ठीक है, तो क्लॉक चिप problem हो सकती है और सिग्नल देने में विफल हो सकती है रिले. आपकी comment के लिए धन्यवाद। *रिले इनपुट सिग्नल की जाँच करते समय कृपया मैनुअल रिले सक्रिय स्विच दबाएँ।
Hi sir mujhe ek help kijia...na Mera timer nahi kam kar raha hai..qki mai phase and nutral galat connet kia tha..ek bar spark kia..fir ab chal nahi raa hai...so kaise banaye
bhai , ye 'Alam Ara' type silent movie bana ke khud hi dekh le, mere ko to kuch samajh nahi aya. Relay fault tha to what did u do......dekh ke khali phokat soldering hataya, fir dekha, fir resoldered....??
Due to higher power input, there was short circuit and burnt. Watch is working but timer is not working. Can you give your address so that I can send this unit for repair