Full Repair and Modification, Dunlop Germanium Fuzz Face! 

It’s cool that you can still buy those vintage style circuit boards.

I added a 9 volt adapter for my 1-Spot power supply years ago to my Fuzz Face and drilled hole in the exterior for the wire to pass through because that thing ATE batteries. That was about the extent of my pedal modding, but this was a lot of fun to watch! Great job!

I went with the full size red FuzzFace as well. Whenever it comes to classic legendary effects in the modern day, I never get the small pedalboard friendly versions. Having it look the same as the one that inspired you is part of the fun. I get stoked every time I look down and see them on the floor. The next pedal I'm going to buy is the Jimmy Page Tone Bender from British Pedal Co. And you bet your ass I'm getting the big OG one.

I work leather, I've been doing it for years- making sheaths, holsters, belt pouches, back packs, whatever ppl wanted- and repairing old saddles and tac. I took my fuzz face and removed the black rubber foot guard thingy- and replaced it with 10 ounce veg. tan. leather that I tooled a biohazard symbol into- it looks wicked. The nut now sits on top of the leather to so- much easier to work with.

That wiring is a work of art.

Thanks for the shout out! Awsome build!

Very cool. I enjoy all of your content, but especially builds/repairs. Recently I started throwing together kits with zero electronics knowledge and watching you work and explain everything is enlightening and inspiring. Thanks.

One of the things I enjoy is watching the different approaches to troubleshooting and design. It’s a great way to learn

Internally, that looks a lot like my Jim Dunlop JD-F2 Fuzz Face after I opened it up after it stopped working, well it didn't just stop working, first it started oscillating like crazy and then it stopped, turned-out the two NTE158 Germanium PNP Transistors were bad, so I ended-up replacing the original circuit board with one I bought online from Pigeon FX, and I elected to go with two BC108C NPN Silicon Transistors (the silver top hat types), that got it working again and it sounded really good and smooth for a Silicon Fuzz Face.

You've got my subscription my man. I do this kinda work every single day and live finding other capable like minds to learn from. Thank you!

Awesome video. Majestic sounds at the end! 🎩

Excellent channel chief! All the best from Canada 🇨🇦!

Very impressive work

23:17 thats such a smart way to adapt, very clean! Loved the video

I bought a new one of these red FF pedals and it was DOA. Problem turned out to be that one of the jacks was contacting the bottom plate, grounding the signal. Rotate the jack, easy fix.

So glad I found your channel, keep up the great work! Cheers

You need a set of rocket sockets, there made of hard plastic, they won't scratch the paint on the pedal. They work well for guitars as well.

Nice job man!

Such meticulous work. Good job !

Great vid! I used to be a tech for a notable pedal manufacturer, and just so you know, there are extended nut driver socket sets available that would allow you to take that footswitch off much easier. Just make sure the socket is hollow all the way through (some are not), and you’ll be able to fit it over the switch. Cheers!

I just subbed. You and Wampler are very informative and entertaining. Thank you for all you do. You and your channel are an amelioration to humanity. Cheers! 😸🤟😎

Some of these newer pcbs are so hard to desolder, because they got heat dissipation pads around the holes. There almost impossible to not burn a pad off. What I do is add solder to it and then use a solder sucker, to remove the solder.

Great job Joe!

Sounds fantastic. I want a fuzz face now lol!

killer! skills abound! thank you for this vid! learned alot!

Man can sokde, man can talk and man can play. That is a great content!

finally someone else that adds solder before desoldering

Your channel is fantastic! I build pedals too but am way behind youdlr knowledge level. But close enough to really value your expertise :) Thanks for your insight

Instead of rubber feet, I just cut some half inch squares of leather, and glued them on the bottom. Those stick on clear rubber raindrop ones from Home Depot that everyone uses suck. Only two-part epoxy keeps them on. Forget that. leather and super glue is all you need. You can get leather from the crafts store, or just cut a piece off an old belt. If you only have thin leather, stack the squares until they're as high as the center screw.

Awesome work...

Great job dude

great job ...

I hand built 2 fuzz faces 1 with BC108 silicon transistors sounds fine.

With germanium transistors, a bias trim pot is the best solution, since they are very sensitive to temperature

Very cool.

It easy to get stuff like that foot switch out by adding a low melt solder to the pins. That stuff will stay liquid easily and allow you to just pull it out after heating, using a small bit of hot air makes it child's play.

Maaaaaan. That sounds really good. I want you to know that im listening on a pair of AKGk240s too.

What amazes me is how simple and empty these things are... So that's how the Astronauts are jamming in space without a pedal board. Wouldn't want one of those getting wrapped around your neck and strangle holding you...

Losing PCB pads can be avoided by wicking or sucking solder completely out of the through holes rather than the melt & pull method that was employed to remove those transistors.

Hey I love your channel so you have a new sub here from Quebec ! I have a question , if you change all the resistors with carbon comps , will there be an audible difference for the better or you hear a difference only with higher voltage amps ?

Nice!

Haven't followed the industry super closely for a bit over a decade, but NTE was always the Dorman Auto parts of the semiconductor world. I'd be stunned if any manufacturer was using them for new designs. Only ever used them for substitutes if there was absolutely no other alternative. And don't even get me started on insulation displacement connectors...

Socket wrench to remove nut someone prolly told you that already great video!

Newmarket sold NKT275 as matched pairs. Dallas Arbiter bought them as pairs. Hfe range was 30 - 90 but rarely exceeded 70.

Exacto knife? trim around the nut. you can always add a small black washer.

If I were rebuilding a Fuzz Face, I'd drill another hole in the top and use a pot for the bias, like the Sun knob on the Analogman fuzz pedals. It would have to avoid hitting the circuit board, of course. But you get some ability to alter the tone with the bias knob, and you can adjust for ambient temperature.

7:16 maybe the germanium transistors were soldered by hand afterwards? They are quite sensitive to heat so they might not have been able to put them in the wave soldering machine

Good job, it's a cool work. Where can I see the wiring diagram for this work?

When I worked on mine, I pulled the rubber back and just reglued it when I was done, the glue stays very sticky , u may not even have to reglue.

Was the cause of the initial failure ever mentioned? Or too many possibilities to sort out and quicker/easier/more fun to rebuild?

I'm curious- you used sockets for the transistors, why not use a trim pot for the bias instead of a fixed resistor based on the reading of the pot? Won't that change a bit if you change transistors?

Bravoooo

Vintage pcb sounds funny to me.

Banzai Music in Germany sell fuzz face PCBs, and sell the rubber tread piece as well

When you are biasing for Q2 what tabs are you connecting to on the 25k pot?

It amazes me how such a big manufacturer as Dunlop can give as much as zero shits for repairability when it comes to the pcb mounting technique that was used in this pedal. I mean come on, why can't you just make the hole cutout at the rubber the same diameter as the freaking nut. I just spent two minutes in fast forward watching someone trying to unscrew a nut for God's sake! Enough of a rant. This was a great video once again! It's really nice watching you build things again. Just a word of caution though, having all these AC signal wires so close in parallel with each other especially in a high gain circuit like this is not the best idea. I know it look nice and I admit that I've done it myself too, but it isn't the best practice electrically speaking.

Connecting a shield at only one side depends, but in this case it's true. But that shield is pointless anyway, since it's in a shielded can anyway and it's powered by a battery.

You can peel the rubber footswitch pad from the top exposing the nut. Much easier

This is really awesome. The Mojo parts kit that you used, where can one find that?

Hey man whats up, im missing a 1k pot for the fuzz control and im almost finishing to build the FF, should i put a 1k resistor to ground instead? How would you do it?

hi Joe, what values would you change in the FF circuit to enhance the glassy effect of rolling back guitar volume?

Where do you get that type of resistors? I've been looking around but can't find them.

Is possible do a mod than emulates a used low voltage battery with a pot? Like a control of the % of energy thats In the circuit? Sorry my bad english

great job really and finally the sound is bad, a loss of signal. the pots of volume and fuzz at full is not the way to get versatile sound, but i think the mod is not that acurrate

use a box spanner on the f/sw nut, but just grind a taper , narrow it down to fit inside the rubber pad, 😇👍

Hey, I'm interested in having a Dunlop JDF2 Classic Fuzz Face Pedal modified. Do you do that?

I am on the side of: Screw that rubber pad. Im cuttin out a wider circle...

Cool sound tho!

checking the 9 volt first?

did you reverse the trannys from stock?

Why does the fuzz face circuit want Q2 to have an HFE at 100 or more? for what reasons

It would be fun to get a deactivated land mine and make it into a fuzz face pedal with the stomp switch being where the land mine firing mechanism goes lol

Trust me when I say that a desoldering gun is a real game-changer.

Hi Gray) cool channel u have. i m looking for a FUZZ for a blues . Could you gimme some advice.... thinking bout King Tone Vintage Fuzz.... or..... wht else can you reccomend to take a look....

I think I'll just peel that rubber off and contact it back on when I'm done.

Nice rebuild other than using old carbon composition resistors. That's just not worth it, even for a non-precision application. They drift and have awful tolerances... Metal film resistors should be the go-to always!

Bruh get you a solder pump iron, no messing with the wick braid.

Amplified Parts sell loads of phenolic FF clone boards. I have one sitting on my bench right now, all populated and waiting for a good deal on a round enclosure... BTW, it sounds like you live next to a dirt flattrack...or maybe it's just that speeding up the video makes cars sound like 2-stroke dirt bikes...

I didn't see a video on a mxr distortion + pedal on your channel, if you want to do one I have one that isn't working and I don't know why!

Man, where are you based? I live in a town called Gray, and it's got me wondering where that name comes from... If you were my neighbor and I didn't ever ask this question I couldn't forgive myself. Hahaha. Have you ever considered doing a series on test equipment? Different rigs, what they do, etc? I'm a low level builder but I really think the next step for me would be learning how to assemble a killer work station. If I could choose one person to clarify the muddy waters of equipment selection, it would def be you... Just a thought! Even if it were just a showcase of what you've got, or what a basic starter setup should have, it would be a great vid. Another side question: I have a bunch of Russian MP16B PNP's... I've breadboarded a bit with them, and like the idea of a Sziklai pair where the first half is a Si NPN, followed by the russian Ge PNP. It would be AWESOME if you did a vid, or vids, showing your biasing process for Darlington/Sziklai pairs. Sorry for the long winded comment! You seem like you might be the kind of guy that actually takes some of this into consideration though, so I thought I'd ask. Even if you don't do this stuff and just stick to teardowns, it's a great channel. Keep it up!

28:10 What's it all about? I need to know!!! Great vid

So you went from a new PCB (epoxy and tin plated traces) to a one sided pcb with non tin traces? Going backwards ehhh? Like vehicles going electric.

I’ve got all the bits and a completely bare fuzz face enclosure. I’m just struggling to figure out how to wire one up, it’s my first go at a pedal build and I can’t find a layout picture that I can follow, have you got any ideas?

Great stuff! Kind of a stretch to call it repair and mod, you pretty much just reused the case. The original circuit still exists and isn't repaired. But there's room for range of views on this.

At the price they sell those pedals, they should de built like that...

This is definitely sloppy seconds. I dooubt they'd come from the factory like that.

150 for a handful of components and an enclosure. Way too high. I can build my own for much less. Good rebuild, though. 👍

Stupidly designed pedal (being the massive circle). To improve it, Put it all inside a much smaller box

The nails....

You need to fix your title to full rebuild because you got as far as taking it out of the housing and decided to just use all new components, pcb, switch even looks like new pots never even stated the original problem. so thats not a full repair its a rebuild.

It is insanely annoying that your hands are flipping and flopping around in the picture at all times. Try to control your ADHD please.